ramips: set the wifi mac address to the same as LAN on witi
[openwrt.git] / target / linux / lantiq /
2015-12-23 blogiclantiq: fix Image Builder
2015-12-23 blogiclantiq: fix PCI_DEVICE_ID_LANTIQ_PCIE
2015-12-23 blogiclantiq: TDW89x0 - increase spi frequency
2015-12-23 blogiclantiq: disable SW_PORTMAP usage in the ethernet driver
2015-12-23 blogiclantiq: Configure LED polarity for TDW8970 and TDW8980.
2015-12-17 blogiclantiq: fix ARV7519RW22 buttons
2015-12-17 blogiclantiq: add the TDW8980 5GHz led
2015-12-17 blogiclantiq: Fix LED handling.
2015-12-17 blogiclantiq: Configure LED polarity for TDW8970.
2015-12-17 blogiclantiq: Configure disabled WLAN bands for TDW89X0.
2015-12-17 blogiclantiq: Allow configuration of ath9k disabled bands...
2015-12-11 jowall: drop old uci-defaults.sh
2015-12-11 blogiclantiq: get rid of ltq-vdsl-fw
2015-12-11 blogiclantiq: fix led setup after switch to uci-defaults...
2015-12-06 jowlantiq: fix logic error in dsl board.d code
2015-12-05 nbdlantiq: add VDSL2 vectoring status information
2015-12-05 nbdlantiq: get rid of the dsl_fw mtd partition
2015-12-05 nbdlantiq: remove 3.18 support
2015-12-04 nbdlantiq: fix a race condition in the SPI driver leading...
2015-12-04 nbdlantiq: re-enable spi-xway for TD-W89X0 now that it...
2015-12-04 nbdlantiq: fix xway spi driver timeout issues
2015-12-04 nbdlantiq: clean up the xrx200 ethernet driver and fix...
2015-12-04 nbdlantiq: move esi calls to dsl_cpe_control scripts to...
2015-12-04 jowlantiq: switch from uci-defaults to board.d
2015-12-02 nbdlantiq: fix up m25p80 device ids (#20975)
2015-11-24 haukelantiq: fix compile error
2015-11-24 nbdkernel: update m25p80 in 4.1 to the latest version...
2015-11-21 blogiclantiq: add phy led config support over devicetree...
2015-11-21 blogiclantiq: tweak DWC2 default parameters
2015-10-25 haukelantiq: add clk_round_rate()
2015-10-25 haukekernel: update kernel 4.1 to version 4.1.11
2015-10-19 blogiclantiq: Synchronize access to the DSL command pipe
2015-10-19 blogiclantiq: Print the status register whenever an error...
2015-10-19 blogiclantiq: Fixed reading the number of RX FIFOs in the...
2015-10-19 blogicRevert "lantiq: activate spi-xway on TDW89X0"
2015-10-11 blogiclantiq: fix use of IRQF_DISABLED in lantiq kmods
2015-10-11 blogiclantiq: bugfix wrong non pre-emptive crc errors output
2015-10-07 blogiclantiq: activate spi-xway on TDW89X0
2015-10-07 blogiclantiq: spi driver fix
2015-10-07 blogiclantiq: bugfix luci lantiq_dsl status
2015-10-05 blogiclantiq: several ARV7519RW22 fixes
2015-10-05 blogiclantiq: make v4.1 the default kernel
2015-10-05 blogiclantiq: Add target TP-Link TD-W8980
2015-10-05 blogiclantiq: fix ath_pci_fixup hang on bridged devices
2015-10-05 blogiclantiq: Change the data-type of mac address in ETOP...
2015-10-05 blogiclantiq: bugfix uninitialized variables
2015-10-04 matteolantiq: fix binutils 2.15.1 build
2015-10-04 haukekernel: update 4.1 to 4.1.10
2015-09-15 rmileckilantiq: update list on NAND devices in platform_pre_upgrade
2015-09-15 blogiclantiq: add platform_pre_upgrade for sysupgrade
2015-09-14 blogiclantiq: get more status information from xDSL
2015-09-14 blogiclantiq: Add AR9 compatibility bits to DWC2 driver
2015-09-14 blogiclantiq: Introduce DWC2 compatible DTS definitions for...
2015-09-14 blogiclantiq: Initialize USB on AR9 platform
2015-09-11 haukekernel: add CONFIG_MIPS_CDMM config option
2015-09-11 nbdlantiq: Use the BAR0 base address in the ath PCI fixup...
2015-09-02 jogokernel: update 3.18 to 3.18.21
2015-08-30 jogolantiq: remove dead EASY33016 image recipe
2015-08-23 jogokernel: update 4.1 to 4.1.6
2015-08-17 blogiclantiq: Support newer versions of the PEF7071 ethernet...
2015-08-14 jogoimage.mk: move KDIR_TMP definition to a central location
2015-08-05 jogoimage: fix jffs2(_nand) image generation
2015-08-05 jogokernel: update 4.1 to 4.1.4
2015-07-24 blogiclantiq: Silence the PCIe error interrupt printk also...
2015-07-22 jogokernel: refresh patches for 4.1
2015-07-12 haukekernel: refresh patches on linux 3.18
2015-07-07 blogiclantiq: Add support for Arcadyan ARV8539PW22 (Speedport...
2015-07-07 blogiclantiq: Add support for the BT Home Hub 5A
2015-07-07 blogiclantiq: Silence the printk when a PCIe error interrupt...
2015-07-07 blogiclantiq: Make the MEI address available for kernel drivers
2015-07-07 blogiclantiq: Change the data-type of mac address in ETOP...
2015-07-07 blogiclantiq: Add support for linux 4.1
2015-06-30 jogokernel: update 3.18 to 3.18.17
2015-06-17 jogokernel: update 3.18 to 3.18.16
2015-06-05 blogiclantiq: Backport gpio-stp-xway to fix the highest bits...
2015-06-05 blogiclantiq: Add support for Arcadyan VGV7510KW22 (known...
2015-06-03 blogiclantiq: Make the CRC32 poly value configurable per...
2015-06-01 jogolantiq: fix VG3503J rootfs offset
2015-05-30 blogiclantiq: fix imagebuilder
2015-05-23 blogiclantiq: Fix initialization of the PCI IRQs when PCIe...
2015-05-23 blogiclantiq: Fix PCIe bus when PCI is also enabled.
2015-05-21 jogokernel: update 3.18 to 3.18.14
2015-05-03 kalozThe ability to read MAC addresses from MTD is useful...
2015-03-27 blogiclantiq: remove arphaned folder
2015-03-17 blogiclantiq/xrx200: cleanup default packages
2015-03-17 blogiclantiq: make xrx200 targets use the upstream dwc2 driver
2015-03-16 blogiclantiq: drop 3.14 support
2015-03-15 nbdlantiq: add a better fix to strip FCS from ethernet...
2015-03-15 nbdlantiq: enable atm-esi by default for xrx200
2015-03-11 blogickenrel: refresh patches
2015-03-11 blogiclantiq: make the new dwc2 support only work for vr9
2015-03-11 blogiclantiq: Convert Zyxel P-2812HNU-FX and TP-Link TD-W8970...
2015-03-11 blogiclantiq: Use platform endianness when accessing dwc2...
2015-03-11 blogiclantiq: Add sensible hw-defaults for dwc2
2015-03-11 blogiclantiq: Configure gpio power output pin when initializi...
2015-03-11 blogiclantiq: Add usb initialization bits from ltq-hcd to...
2015-03-06 blogickernel: move KERNFS to generic config
2015-03-06 blogickernel: disable ARCH_NEEDS_CPU_IDLE_COUPLED
2015-03-06 blogickernel: move MTD_SPLIT_SUPPORT to generic config
2015-03-06 blogickernel: remove GENERIC_NET_UTILS from platform configs
next