target/linux/lantiq/dts/ARV7519PW.dts

   1 /dts-v1/;
   2
   3 /include/ "danube.dtsi"
   4
   5 / {
   6         model = "ARV7519PW - Astoria Networks";
   7
   8         chosen {
   9                 bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
  10         };
  11
  12         memory@0 {
  13                 reg = <0x0 0x4000000>;
  14         };
  15
  16         sram@1F000000 {
  17                 vmmc@107000 {
  18                         status = "okay";
  19                 };
  20         };
  21
  22         fpi@10000000 {
  23                 localbus@0 {
  24                         nor-boot@0 {
  25                                 compatible = "lantiq,nor";
  26                                 bank-width = <2>;
  27                                 reg = <0 0x0 0x2000000>;
  28                                 #address-cells = <1>;
  29                                 #size-cells = <1>;
  30
  31                                 partition@0 {
  32                                         label = "uboot";
  33                                         reg = <0x00000 0x40000>;
  34                                         read-only;
  35                                 };
  36
  37                                 partition@40000 {
  38                                         label = "uboot_env";
  39                                         reg = <0x40000 0x20000>;
  40                                 };
  41
  42                                 partition@60000 {
  43                                         label = "firmware";
  44                                         reg = <0x60000 0xf80000>;
  45                                 };
  46
  47                                 partition@fe0000 {
  48                                         label = "board_config";
  49                                         reg = <0xfe0000 0x20000>;
  50                                         read-only;
  51                                 };
  52                         };
  53
  54                         mac_addr {
  55                                 compatible = "lantiq,eth-mac";
  56                                 reg = <0 0xfe0016 0x6>;
  57                                 mac-increment = <2>;
  58                         };
  59                 };
  60
  61                 gpio: pinmux@E100B10 {
  62                         pinctrl-names = "default";
  63                         pinctrl-0 = <&state_default>;
  64
  65                         state_default: pinmux {
  66                                 ebu {
  67                                         lantiq,groups = "ebu cs1";
  68                                         lantiq,function = "ebu";
  69                                 };
  70                                 pci_in {
  71                                         lantiq,groups = "req1";
  72                                         lantiq,function = "pci";
  73                                         lantiq,open-drain = <1>;
  74                                         lantiq,pull = <2>;
  75                                         lantiq,output = <0>;
  76                                 };
  77                                 pci_out {
  78                                         lantiq,groups = "gnt1";
  79                                         lantiq,function = "pci";
  80                                         lantiq,pull = <0>;
  81                                         lantiq,output = <1>;
  82                                 };
  83                                 pci_rst {
  84                                         lantiq,pins = "io21";
  85                                         lantiq,pull = <2>;
  86                                         lantiq,output = <1>;
  87                                 };
  88                                 switch_rst {
  89                                         lantiq,pins = "io19";
  90                                         lantiq,pull = <2>;
  91                                         lantiq,output = <1>;
  92                                 };
  93                         };
  94                 };
  95
  96                 etop@E180000 {
  97                         phy-mode = "mii";
  98                 };
  99
 100                 /* warning: passive port
 101                 only works with active devices */
 102                 ifxhcd@E101000 {
 103                         status = "okay";
 104                 };
 105
 106                 pci@E105400 {
 107                         status = "okay";
 108                         lantiq,external-clock;
 109                         gpio-reset = <&gpio 21 0>;
 110                         req-mask = <0xf>;
 111                 };
 112         };
 113
 114         ralink_eep {
 115                 compatible = "ralink,eeprom";
 116                 ralink,eeprom = "RT2860.eeprom";
 117         };
 118
 119         gpio-keys-polled {
 120                 compatible = "gpio-keys-polled";
 121                 #address-cells = <1>;
 122                 #size-cells = <0>;
 123                 poll-interval = <100>;
 124
 125                 rfkill {
 126                         label = "rfkill";
 127                         gpios = <&gpio 11 1>;
 128                         linux,code = <0xf7>;
 129                 };
 130                 reset {
 131                         label = "reset";
 132                         gpios = <&gpio 28 1>;
 133                         linux,code = <0x198>;
 134                 };
 135         };
 136
 137         gpio-leds {
 138                 compatible = "gpio-leds";
 139                 power {
 140                         label = "power";
 141                         gpios = <&gpio 2 1>;
 142                         default-state = "off";
 143                 };
 144                 power2 {
 145                         label = "power2";
 146                         gpios = <&gpio 14 1>;
 147                 };
 148                 online {
 149                         label = "online";
 150                         gpios = <&gpio 3 1>;
 151                 };
 152                 online2 {
 153                         label = "online2";
 154                         gpios = <&gpio 30 1>;
 155                 };
 156                 wifi {
 157                         label = "wifi";
 158                         gpios = <&gpio 12 1>;
 159                 };
 160                 wifi2 {
 161                         label = "wifi2";
 162                         gpios = <&gpio 10 1>;
 163                 };
 164                 wifi3 {
 165                         label = "wifi3";
 166                         gpios = <&gpio 6 1>;
 167                 };
 168                 voice {
 169                         label = "voice";
 170                         gpios = <&gpio 31 1>;
 171                 };
 172                 wps {
 173                         label = "wps";
 174                         gpios = <&gpio 15 1>;
 175                 };
 176                 wps2 {
 177                         label = "wps2";
 178                         gpios = <&gpio 7 1>;
 179                 };
 180                 wps3 {
 181                         label = "wps3";
 182                         gpios = <&gpio 23 1>;
 183                 };
 184                 dsl {
 185                         label = "dsl";
 186                         gpios = <&gpio 4 1>;
 187                 };
 188                 lan {
 189                         label = "lan";
 190                         gpios = <&gpio 1 1>;
 191                 };
 192                 tv {
 193                         label = "tv";
 194                         gpios = <&gpio 20 1>;
 195                 };
 196                 upgrade {
 197                         label = "upgrade";
 198                         gpios = <&gpio 29 1>;
 199                 };
 200         };
 201
 202         /* is there another way to "reserve" the GPIO? */
 203         gpio_export {
 204                 compatible = "gpio-export";
 205                 #size-cells = <0>;
 206
 207                 switch {
 208                         gpio-export,name = "switch";
 209                         gpio-export,output = <1>;
 210                         gpios = <&gpio 19 0>;
 211                 };
 212         };
 213 };