2 * Copyright 2013 Gateworks Corporation
4 * The code contained herein is licensed under the GNU General Public
5 * License. You may obtain a copy of the GNU General Public License
6 * Version 2 or later at the following locations:
8 * http://www.opensource.org/licenses/gpl-license.html
9 * http://www.gnu.org/copyleft/gpl.html
16 model = "Gateworks Ventana GW54XX";
17 compatible = "gw,imx6q-gw54xx", "gw,ventana", "fsl,imx6q";
19 /* these are used by bootloader for disabling nodes */
54 reg = <0x10000000 0x40000000>;
58 compatible = "gpio-leds";
62 gpios = <&gpio4 6 0>; /* 102 -> MX6_PANLEDG */
64 linux,default-trigger = "heartbeat";
69 gpios = <&gpio4 7 0>; /* 103 -> MX6_PANLEDR */
70 default-state = "off";
75 gpios = <&gpio4 15 1>; /* 111 -> MX6_LOCLED# */
76 default-state = "off";
81 compatible = "simple-bus";
84 compatible = "regulator-fixed";
85 regulator-name = "2P5V";
86 regulator-min-microvolt = <2500000>;
87 regulator-max-microvolt = <2500000>;
92 compatible = "regulator-fixed";
93 regulator-name = "3P3V";
94 regulator-min-microvolt = <3300000>;
95 regulator-max-microvolt = <3300000>;
99 reg_usb_otg_vbus: usb_otg_vbus {
100 compatible = "regulator-fixed";
101 regulator-name = "usb_otg_vbus";
102 regulator-min-microvolt = <5000000>;
103 regulator-max-microvolt = <5000000>;
104 gpio = <&gpio3 22 0>;
110 compatible = "fsl,imx6q-sabrelite-sgtl5000",
111 "fsl,imx-audio-sgtl5000";
112 model = "imx6q-sabrelite-sgtl5000";
113 ssi-controller = <&ssi1>;
114 audio-codec = <&codec>;
116 "MIC_IN", "Mic Jack",
117 "Mic Jack", "Mic Bias",
118 "Headphone Jack", "HP_OUT";
125 pinctrl-names = "default";
126 pinctrl-0 = <&pinctrl_audmux_3>;
135 pinctrl-names = "default";
136 pinctrl-0 = <&pinctrl_enet_1>;
138 phy-reset-gpios = <&gpio1 30 0>;
143 pinctrl-names = "default";
144 pinctrl-0 = <&pinctrl_gpmi_nand_2>;
150 clock-frequency = <100000>;
151 pinctrl-names = "default";
152 pinctrl-0 = <&pinctrl_i2c1_1>;
155 compatible = "atmel,24c02";
161 compatible = "atmel,24c02";
167 compatible = "atmel,24c02";
173 compatible = "atmel,24c02";
179 compatible = "atmel,24c02";
185 compatible = "dallas,ds1672";
190 compatible = "nxp,pca9555";
197 compatible = "gw,gsp";
204 clock-frequency = <100000>;
205 pinctrl-names = "default";
206 pinctrl-0 = <&pinctrl_i2c2_2>;
209 compatible = "fsl,pfuze100";
213 pciswitch: pex8609@3f {
214 compatible = "plx,pex8609";
218 pciclkgen: si52147@6b {
219 compatible = "sil,si52147";
226 clock-frequency = <100000>;
227 pinctrl-names = "default";
228 pinctrl-0 = <&pinctrl_i2c3_2>;
231 compatible = "fsl,sgtl5000";
233 clocks = <&clks 169>;
234 VDDA-supply = <®_2p5v>;
235 VDDIO-supply = <®_3p3v>;
238 accelerometer: mma8450@1c {
239 compatible = "fsl,mma8450";
243 videoout: adv7393@2a {
244 compatible = "adi,adv7393";
248 videoin: adv7180@20 {
249 compatible = "adi,adv7180";
254 compatible = "adi,adv7611";
258 touchscreen: egalax_ts@04 {
259 compatible = "eeti,egalax_ts";
261 wakeup-gpios = <&gpio1 12 0>;
266 pinctrl-names = "default";
267 pinctrl-0 = <&pinctrl_hog>;
270 pinctrl_hog: hoggrp {
272 MX6Q_PAD_EIM_D22__GPIO3_IO22 0x80000000 /* OTG_PWR_EN */
273 MX6Q_PAD_EIM_D19__GPIO3_IO19 0x80000000 /* SPINOR_CS0# */
274 MX6Q_PAD_KEY_COL0__GPIO4_IO06 0x80000000 /* user1 led */
275 MX6Q_PAD_KEY_ROW0__GPIO4_IO07 0x80000000 /* user2 led */
276 MX6Q_PAD_KEY_ROW4__GPIO4_IO15 0x80000000 /* user3 led */
277 MX6Q_PAD_SD1_DAT0__GPIO1_IO16 0x80000000 /* USBHUB_RST# */
278 MX6Q_PAD_ENET_TX_EN__GPIO1_IO28 0x80000000 /* PCIE IRQ */
279 MX6Q_PAD_ENET_TXD1__GPIO1_IO29 0x80000000 /* PCIE RST */
280 MX6Q_PAD_SD1_DAT3__GPIO1_IO21 0x80000000 /* MIPI_DIO */
281 MX6Q_PAD_GPIO_0__CCM_CLKO1 0x000130b0 /* AUD4_MCK */
282 MX6Q_PAD_GPIO_2__GPIO1_IO02 0x80000000 /* CAN_STBY */
289 reset-gpio = <&gpio1 29 0>;
292 eth1: sky2@8 { /* MAC/PHY on bus 8 */
293 compatible = "marvell,sky2";
294 /* Filled in by U-Boot */
295 mac-address = [ 00 00 00 00 00 00 ];
304 fsl,mode = "i2s-slave";
309 pinctrl-names = "default";
310 pinctrl-0 = <&pinctrl_uart1_2>;
315 pinctrl-names = "default";
316 pinctrl-0 = <&pinctrl_uart2_2>;
321 pinctrl-names = "default";
322 pinctrl-0 = <&pinctrl_uart3_1>;
328 pinctrl-names = "default";
329 pinctrl-0 = <&pinctrl_uart5_1>;
333 vbus-supply = <®_usb_otg_vbus>;
334 pinctrl-names = "default";
335 pinctrl-0 = <&pinctrl_usbotg_1>;
336 disable-over-current;
345 pinctrl-names = "default";
346 pinctrl-0 = <&pinctrl_usdhc3_2>;
347 cd-gpios = <&gpio7 0 0>;
348 vmmc-supply = <®_3p3v>;