luka [Tue, 10 May 2016 22:37:14 +0000 (22:37 +0000)]
ramips: introduce serial0 aliases
This patch introduces serial0 aliases in the ramips DTS files, which can
then be used to denote the active console instead of relying on bootargs.
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49355
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:37:12 +0000 (22:37 +0000)]
ubox: make logging code honour the hostname properly
Signed-off-by: John Crispin <john@phrozen.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49354
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:37:10 +0000 (22:37 +0000)]
brcm47xx: fix wgt634u port assignment, broken since openwrt r47866
Signed-off-by: Russell Senior <russell@personaltelco.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49353
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:37:09 +0000 (22:37 +0000)]
ramips: mt7620: [UPSTREAM] fix USB frequency scaling
The logic for the SoC check got inverted. We need to check if it's
not a MT76x8.
Signed-off-by: D. Andrei Măceș <dmaces@nd.edu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49352
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:37:07 +0000 (22:37 +0000)]
ramips: Fix alphabetical sorting for 02_network
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49351
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:37:03 +0000 (22:37 +0000)]
ramips: Don't use a VLAN for the single ethernet port of the A5-V11.
This router only has one ethernet port, so a VLAN is useless here, now that the rt3050 TCP bug that happened without VLANs has been fixed for a very long time.
Add this router to the VLAN-less config that is used by other single-port routers.
Also fix MAC address detection code since this router has no WAN port.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49350
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:37:02 +0000 (22:37 +0000)]
ramips: Fix network for routers without VLANs on eth0.
Some routers only have one port, so eth0 is used without VLANs for them.
Revision r47720 introduced some changes, but wrongly confused "enable" with "reset".
VLANs need to be disabled for those routers, and the switch may be reset.
Fix this, by explicitly disabling VLANs instead of resetting the switch for these routers.
Also merge duplicate configuration for the "m2m".
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49349
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:37:00 +0000 (22:37 +0000)]
ncurses: install pkg-config files to fix util-linux build breakage
Signed-off-by: Felix Fietkau <nbd@nbd.name>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49348
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:59 +0000 (22:36 +0000)]
ncurses: remove libncurses, provide it via libncursesw
Signed-off-by: Felix Fietkau <nbd@nbd.name>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49347
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:57 +0000 (22:36 +0000)]
metadata.pl: add support for selecting packages available only via PROVIDES
Signed-off-by: Felix Fietkau <nbd@nbd.name>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49346
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:56 +0000 (22:36 +0000)]
kernel: add workaround to rebuild vdso-o32.so.dbg
Building for octeon fails with
'arch/mips/vdso/vdso-o32.so.dbg' already contains a '.MIPS.abiflags'
section
if the file already exists from a prior build.
Use the same workaround as the one for vdso.so.dbg committed in
9eb155353a5f5137ec85a5b5b0287af63c544710.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49345
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:55 +0000 (22:36 +0000)]
toolchain: gcc: fix build with GCC 6
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49344
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:53 +0000 (22:36 +0000)]
tools: mkimage: sync include/linux/compiler*.h with u-boot master
Fixes build with GCC 6.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49343
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:51 +0000 (22:36 +0000)]
tools: pkg-config: fix build with GCC 6
Fixes the following error:
gdate.c: In function ‘g_date_strftime’:
gdate.c:2497:7: error: format not a string literal, format string not checked [-Werror=format-nonliteral]
tmplen = strftime (tmpbuf, tmpbufsize, locale_format, &tm);
^~~~~~
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49342
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:50 +0000 (22:36 +0000)]
tools: make-ext4fs: fix build regression on mac os x
Including sys/sysmacros.h is not portable
Signed-off-by: Felix Fietkau <nbd@nbd.name>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49341
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:49 +0000 (22:36 +0000)]
base-files: evaluate uci-defaults on run-time installations
Packages may install scripts into /etc/uci-defaults to be executed once
after installation, usually at the first boot of the target. This works
fine if the package was installed to the rootfs during build or using
the ImageBuilder.
If the package is installed using opkg during run-time uci-defaults
were applied only after a reboot of the device. Avoid the need to
reboot by evaluting the package's uci-defaults in default-postinst.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49340
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:47 +0000 (22:36 +0000)]
libiconv: add all ASCII aliases
This patch adds missing ASCII aliases to the libiconv stub in order to avoid conversion errors like https://github.com/openwrt/packages/issues/2373
Signed-off-by: Gergely Kiss <mail.gery@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49339
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:45 +0000 (22:36 +0000)]
xtables-addons: Avoid redefinition of SHRT_MAX in lua packet script
Patch Lua packet script defines SHRT_MAX which is already defined in <linux/kernel.h> and
is included indirectly by lauxlib.h. Fix the redefintion as it leads to compile failure
on systems which treat macro redefinition as an error
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49338
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:44 +0000 (22:36 +0000)]
fstools: fix snapshot support
Signed-off-by: John Crispin <john@phrozen.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49337
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:43 +0000 (22:36 +0000)]
fstools: update to latest git HEAD
fixes snapshot support
Signed-off-by: John Crispin <john@phrozen.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49336
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:41 +0000 (22:36 +0000)]
fstools: update to latest git HEAD
this adds the remount command to the block tool
Signed-off-by: John Crispin <john@phrozen.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49335
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:39 +0000 (22:36 +0000)]
kernel: add a workaround to rebuild vdso.so.dbg after genvdso
Currently the build fails with
'arch/mips/vdso/vdso.so.dbg' already contains a '.MIPS.abiflags' section
if the file already exists from a prior build.
Add a makefile rule to force the rebuild of vdso.so.dbg if genvdso has
has been changed to workaround the failure.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49334
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:38 +0000 (22:36 +0000)]
dropbear: Make utmp and putuline support configurable via seperate config options
Utmp support tracks who is currenlty logged in by logging info to the file /var/run/utmp (supported by busybox)
Putuline support will use the utmp structure to write to the utmp file
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49333
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:36 +0000 (22:36 +0000)]
netifd: Add configurable DHCP release behavior
Make sending a DHCP release configurable when the client exits allowing to clean up
IP/mac state info in intermediate devices.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49332
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:35 +0000 (22:36 +0000)]
xtables-addons: Fix Lua packet script implementation
lua_packet_segment parameter start has type char pointer; in function lua_tg
it's assigned an uint16 value generating compiler warnings obviously indicating
posssible seg fault problems. Fix the issue by using the correct skb functions
so the parameter points to the position inside the sk_buff
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Stijn Cleynhens <stijn.cleynhens@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49331
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:33 +0000 (22:36 +0000)]
lantiq: fix xway image building
Commit
8c130dd (lantiq: use new image build process for some images) broke
image generation for the xway target since the generated macros reference not
existing WBMRA.dts and WBMRB.dts files leading to the following build error:
mips-openwrt-linux-musl-cpp: error: ../dts/WBMRA.dts: No such file or directory
mips-openwrt-linux-musl-cpp: warning: '-x assembler-with-cpp' after last input file has no effect
mips-openwrt-linux-musl-cpp: fatal error: no input files
Previously both the WBMRA and WBMRB profiles shared a common WBMR DT since
the only difference is the embedded firmware kmod package.
Extend the lantiqImage macro to optionally support specifying a different
DTS file and use this facility to let the both WBMR profiles reference the
correct device tree file.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49330
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:32 +0000 (22:36 +0000)]
x86: remove old references to kmod-acpi-button
The kmod-acpi-button functionality is included in the kernel where needed
and the corresponding kmod package has been deleted long ago, therfor drop
the remaining references now.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49329
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:30 +0000 (22:36 +0000)]
kernel: fix ip6_tunnel compilation
Replace undefined iph for ip_hdr(skb)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49328
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:28 +0000 (22:36 +0000)]
base-files: remove ununsed login.sh
Signed-off-by: John Crispin <john@phrozen.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49327
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:27 +0000 (22:36 +0000)]
base-files: Allow to disable failsafe mode
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49326
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:25 +0000 (22:36 +0000)]
image / basefiles: make console password configurable
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
Signed-off-by: John Crispin <john@phrozen.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49325
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:15 +0000 (22:36 +0000)]
base-files: fix error message during boot
preinit spews out this message
"cat: can't open '/proc/device-tree/model': No such file or directory"
Signed-off-by: John Crispin <john@phrozen.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49324
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:13 +0000 (22:36 +0000)]
scripts: metadata: add CONFIG_TARGET_SUBTARGET symbol
Add a new string symbol "CONFIG_TARGET_SUBTARGET" which contains the name of
the chosen subtarget or "generic" if there are no subtargets available.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49323
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:12 +0000 (22:36 +0000)]
busybox: fix setting the kernel timezone
The settimeofday() syscall wrapper provided by musl filters out the timezone
argument, breaking the ability to set the kernel timezone through the function.
Adjust busybox patch to issue the syscall directly in order to circumvent the
problem.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49322
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:10 +0000 (22:36 +0000)]
netifd: Send DHCP release when client exits
Let DHCP client send a release when it exists so the DHCP server is
informed the IP address is released and allowing to clean up IP/mac
state info in intermediate devices.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49321
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:08 +0000 (22:36 +0000)]
netifd: fix default ip rules
Update to latest HEAD in order to remove the faulty "prelocal" ip rule leading
to unexpected policy rule precedence.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49320
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:06 +0000 (22:36 +0000)]
x86: search PARTUUID in any block device
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49319
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 10 May 2016 22:36:04 +0000 (22:36 +0000)]
x86: make sysupgrade work without partx
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49318
3c298f89-4303-0410-b956-
a3cf2f4a3e73
rmilecki [Mon, 9 May 2016 18:10:35 +0000 (18:10 +0000)]
mtd: add -c option for specifying amount of data to be used for checksum
So far fixtrx was calculating checksum over amount of data matching
partition erase size. It was mostly a workaround of checksum problem
after changing anything in initial TRX content (e.g. formatting JFFS2).
Its main purpose was to make bootloader accept modified TRX. This didn't
provide much protection of flash data against corruption.
This new option lets caller request calculating checksum over a bigger
amount of data. It may be used e.g. to include whole kernel data for
checksum and hopefully make bootloader go info failsafe mode if
something goes wrong.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49317
3c298f89-4303-0410-b956-
a3cf2f4a3e73
rmilecki [Mon, 9 May 2016 18:10:30 +0000 (18:10 +0000)]
mtd: trx: use separated buffer for TRX header
We plan to adjust usage of the main buffer to allow reading custom
amount of data for CRC32. This means we need another buffer that will be
always block aligned.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49316
3c298f89-4303-0410-b956-
a3cf2f4a3e73
rmilecki [Mon, 9 May 2016 15:33:42 +0000 (15:33 +0000)]
mtd: seama: exit with error if Seama header wasn't found
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49314
3c298f89-4303-0410-b956-
a3cf2f4a3e73
rmilecki [Mon, 9 May 2016 12:53:39 +0000 (12:53 +0000)]
mtd: seama: fix image data handling
1) Put sanity checks in one place
2) Respect provided offset
3) Read only as much data as needed for MD5 calculation
Thanks to the last change this is a great speedup and memory saver. On
devices with NAND flash we were allocating & reading about 128 MiB while
something about 8 MiB is enough.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49309
3c298f89-4303-0410-b956-
a3cf2f4a3e73
rmilecki [Mon, 9 May 2016 12:53:36 +0000 (12:53 +0000)]
mtd: seama: move buf allocation to the MD5 function
This buf is only used in this function now, so lets move it there.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49308
3c298f89-4303-0410-b956-
a3cf2f4a3e73
rmilecki [Mon, 9 May 2016 12:53:33 +0000 (12:53 +0000)]
mtd: seama: update MD5 using header in the first block buffer
This will allow separating first block buffer from a buffer used for MD5
calculation.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49307
3c298f89-4303-0410-b956-
a3cf2f4a3e73
rmilecki [Mon, 9 May 2016 12:53:29 +0000 (12:53 +0000)]
mtd: seama: add md5 to header struct
This allows us to drop some extra offset calculations and simplifies
code a bit.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49306
3c298f89-4303-0410-b956-
a3cf2f4a3e73
rmilecki [Mon, 9 May 2016 09:54:48 +0000 (09:54 +0000)]
mtd: check for Seama magic early when fixing MD5
This avoid long (and unneeded) process of reading all data in case of
running on MTD not containig Seama entity.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49304
3c298f89-4303-0410-b956-
a3cf2f4a3e73
rmilecki [Mon, 9 May 2016 07:51:50 +0000 (07:51 +0000)]
mtd: add missing breaks in a switch
On platforms supporting both: TRX and Seama calling "fixtrx" was
resulting in trying to fix Seama as well.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49301
3c298f89-4303-0410-b956-
a3cf2f4a3e73
rmilecki [Mon, 9 May 2016 07:51:45 +0000 (07:51 +0000)]
mtd: use tabs for indents
This makes code style consistent across the whole file.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49300
3c298f89-4303-0410-b956-
a3cf2f4a3e73
rmilecki [Thu, 5 May 2016 14:56:57 +0000 (14:56 +0000)]
kernel: update kernel 4.1 to version 4.1.23
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49296
3c298f89-4303-0410-b956-
a3cf2f4a3e73
jow [Wed, 4 May 2016 12:04:58 +0000 (12:04 +0000)]
openssl: Update to version 1.0.2h
Bump to the latest version, fixes several security issues:
* CVE-2016-2107, CVE-2016-2105, CVE-2016-2106, CVE-2016-2109, CVE-2016-2176
More details at https://www.openssl.org/news/openssl-1.0.2-notes.html
Signed-off-by: Michal Hrusecky <Michal.Hrusecky@nic.cz>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49295
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 2 May 2016 18:51:20 +0000 (18:51 +0000)]
ramips: Drop hacky switch workaround for failsafe on rt3x5x and rt5350.
The new rt3050 switch driver doesn't have problems with TCP when not
using VLANs.
This piece of code also broke failsafe for all routers where the LAN
port is not wired to port 0 of the internal switch.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49293
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 2 May 2016 18:51:13 +0000 (18:51 +0000)]
ramips: Disable all ethernet ports except port 0 on A5-V11.
Port 0 is the only ethernet port on this router, so disable all other PHYs
in order to save power.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49292
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 2 May 2016 18:51:09 +0000 (18:51 +0000)]
ramips: Disable all ethernet ports except port 4 on HT-TM02.
Port 4 is the only ethernet port on this router, so disable all other PHYs
in order to save power.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49291
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 2 May 2016 18:51:05 +0000 (18:51 +0000)]
ramips: Get rt3050 ethernet ports to be disabled from the device tree.
This patch allows configuring ports to be disabled in the device tree; this
saves power, since disabling ports here actually disables power to ethernet
PHYs.
Line 444 enables all ethernet ports, so line 487 is getting zero ports to be
disabled, except for port 5 in SoCs where this is not implemented as it will
be sticky disabled in register POC0. Because of this, the code will still read
the switch configuration and OR it to the device tree setting.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49290
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 2 May 2016 18:51:01 +0000 (18:51 +0000)]
ramips: Fix comment in rt3050 ethernet switch driver.
Line 444 is actually enabling all switch ports by setting the disable bits
to 0. This needs to be done because the bootloader sets all ports to disabled
by default (which is the case for at least one router based on RT5350).
So, this patch fixes the comment in line 443.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49289
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 2 May 2016 18:50:56 +0000 (18:50 +0000)]
ramips: Fix documentation for the rt3050 switch driver.
The prefix used in the driver is now "mediatek" instead of "ralink".
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49288
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 2 May 2016 18:50:52 +0000 (18:50 +0000)]
ramips: Fix multicast ICMPv6 for the rt3050 ethernet switch.
The FCT2 esw register should be set to 0x2500C to have "unknown IPv6
multicast" packets broadcasted to every port, instead of dropped.
The previous value only let those packets go through ports 1 and 3.
"Unknown IPv6 multicast" packets include packets needed by ICMPv6 echo
requests addressed to well-known addresses, such as ff02::1 (MAC address
is 33:33:00:00:00:01 in this case).
Please note that by default ICMPv6 echo requests to ff02::1 are not replied
to by the router because of ip6tables considering those packets to be invalid.
But this is another bug/patch. ;)
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49287
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 2 May 2016 18:50:48 +0000 (18:50 +0000)]
ar71xx: add TP-Link TL-WR810N support
This patch adds support for the TP-Link TL-WR810N.
https://wiki.openwrt.org/toh/tp-link/tl-wr810n
Signed-off-by: Jens Steinhauser <jens.steinhauser@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49286
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 2 May 2016 18:50:40 +0000 (18:50 +0000)]
ubox: turn logd into a separate package
Currently system log is always included as a part of ubox.
Add logd as a seperate package and add it to default packages list.
Signed-off-by: Andrej Vlasic <andrej.vlasic@sartura.hr>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49285
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 2 May 2016 18:50:35 +0000 (18:50 +0000)]
lantiq: VGV7510KW22BRN - set the phy clock source
VGV7510KW2 with VRX288 v1.2 has brnboot 1.8 installed. Starting with
this brnboot version, the "GPHY Clock Source" isn't set anymore by
brnboot, with the result that xrx200-net fails to probe/initialize the
phys.
Use the phy clock source device tree binding to specify the clock source.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49284
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 2 May 2016 18:50:31 +0000 (18:50 +0000)]
lantiq: add device tree binding for the phy clock source
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49283
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 2 May 2016 18:50:27 +0000 (18:50 +0000)]
lantiq: VGV7510KW22BRN - support dual-image
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49282
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 2 May 2016 18:50:23 +0000 (18:50 +0000)]
lantiq: handle the dual-firmware layout of brnboot
brnboot based devices can have two Image partitions. When flashing
images via the brnboot recovery web interface, the Image partitions are
written alternating.
The current active Image partition is stored in the first byte of the
Primary_Setting partition by using 0x00 for Code_Image_0 and 0x01 for
Code_Image_1.
By using the information about the active "Code Image", it is possible
to ensure that the rootfs belongs to the current booted Image/Kernel.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49281
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 2 May 2016 18:50:18 +0000 (18:50 +0000)]
lantiq: move partitions into partion table node
Starting with kernel 4.4, the use of partitions as direct subnodes of the
mtd device is discouraged and only supported for backward compatiblity
reasons.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49280
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 2 May 2016 18:50:10 +0000 (18:50 +0000)]
lantiq: use sysupgrade.bin postfix for tplink images
Use the same name for TP-Link images as it was with the old image build
code.
Move the BOARD_ID export to the TP-Link image build recipe, to indicate
that the variable is only related in this context.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49279
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 2 May 2016 18:50:06 +0000 (18:50 +0000)]
lantiq: VG3503J - use the same PHY led functionality as the OEM firmware
Based on the vg3503j_gphy_led.sh script published in the VG3503J wiki
article, the OEM Firmware uses the following PHY led functionality:
gphy led 0: LINK/ACTIVITY
gphy led 1: LINK
gphy led 2: ACTIVITY
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49278
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 2 May 2016 18:50:00 +0000 (18:50 +0000)]
ar71xx: Fix eth0 support for Ubiquiti UniFi AP AC
Fix eth0 support for the Ubiquiti UniFi AP AC
Signed-off-by: Paul Wassi <p.wassi at gmx.at>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49277
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Sat, 30 Apr 2016 16:53:27 +0000 (16:53 +0000)]
base-files: fix group/user settings after sysupgrade
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49276
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Sat, 30 Apr 2016 16:53:21 +0000 (16:53 +0000)]
base-files: split user/group addition code into a function
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49275
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Fri, 29 Apr 2016 11:35:26 +0000 (11:35 +0000)]
ppp: Add ppp-mod-passwordfd subpackage to ppp
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49274
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Fri, 29 Apr 2016 11:35:20 +0000 (11:35 +0000)]
dnsmasq: Add conntrack support in the full variant
Conntrack support reads the connection track mark associated with
incoming DNS queries and sets the same mark value on the upstream
forwarded DNS query. This can be usefull to track traffic generated
by dnsmasq to associate it with the clients who generate the queries,
usefull for bandwidth accouting and firewall.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49273
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Fri, 29 Apr 2016 11:35:15 +0000 (11:35 +0000)]
dropbear: Add procd interface triggers when interface config is specified
A dropbear instance having an interface config won't start if the interface is down as no
IP address is available.
Adding interface triggers for each configured interface executing the dropbear reload script
will start the dropbear instance when the interface is up.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49272
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Fri, 29 Apr 2016 11:35:10 +0000 (11:35 +0000)]
iproute2: Add package for nstat utility
Add support for the command line utility nstat displaying network statistics
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49271
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Fri, 29 Apr 2016 11:35:05 +0000 (11:35 +0000)]
lantiq: use the same functionality for all ethernet phys led
The VGV7510KW22 has the leds for LAN1-3 connected to pin1 of the phys
and the led for LAN4 connect to pin0 of the phy. This results with the
current configuration in a fast flashing LAN4 led as soon as a network
cable is connected. Something similar was reported on the forum[1] for
the VGV7519 as well.
Since it isn't predicable to which pin a (single) phy led is connected,
use the (default) pin1 functionality
Constant On: 10/100/1000MBit
Blink Fast: None
Blink Slow: None
Pulse: TX/RX
for all ethernet phy leds.
After checking pictures of all vr9 boards, it looks like only the VG3503J
has more than one led connected per phy. Using the phy led device tree
bindings to assign the functionality to the "additional" leds, the
VG3503J phy leds should behave as before.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
[1] https://forum.openwrt.org/viewtopic.php?pid=321523
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49270
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Fri, 29 Apr 2016 11:35:01 +0000 (11:35 +0000)]
lantiq: fix minor typos in 11G/22F phy driver
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49269
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Fri, 29 Apr 2016 11:34:56 +0000 (11:34 +0000)]
ramips: add support for Planex MZK-EX750NP.
add support for Planex MZK-EX750NP.
MZK-EX750NP is MT7620A and MT7610E based 11ac wifi repeater.
Built-in power supply.
64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49268
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Fri, 29 Apr 2016 11:34:48 +0000 (11:34 +0000)]
scripts: avoid hard-coded paths in scripts
Signed-off-by: Iblis Lin <e196819@hotmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49267
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Fri, 29 Apr 2016 11:34:44 +0000 (11:34 +0000)]
base-files: evaluate uci-defaults on run-time installations
Packages may install scripts into /etc/uci-defaults to be executed once
after installation, usually at the first boot of the target. This works
fine if the package was installed to the rootfs during build or using
the ImageBuilder.
If the package is installed using opkg during run-time uci-defaults
were applied only after a reboot of the device. Avoid the need to
reboot by evaluting the package's uci-defaults in default-postinst.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49266
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Fri, 29 Apr 2016 11:34:31 +0000 (11:34 +0000)]
mediatek: sync patches and add more ethernet stability fixes
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49265
3c298f89-4303-0410-b956-
a3cf2f4a3e73
rmilecki [Wed, 27 Apr 2016 21:20:45 +0000 (21:20 +0000)]
bcm53xx: add m25p80 workaround for SPI flash writing problems
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49264
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Wed, 27 Apr 2016 08:58:15 +0000 (08:58 +0000)]
mediatek: sync and patches add support for several boards
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49263
3c298f89-4303-0410-b956-
a3cf2f4a3e73
rmilecki [Wed, 27 Apr 2016 08:04:30 +0000 (08:04 +0000)]
bcm53xx: support SPI-NOR on dual flash devices
We need it to access NVRAM.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49262
3c298f89-4303-0410-b956-
a3cf2f4a3e73
rmilecki [Tue, 26 Apr 2016 17:08:53 +0000 (17:08 +0000)]
bcm53xx: switch to m25p80 and drop bcm53xxspiflash
For some time now m25p80 supports 32 MiB flashes and we just needed to
patch spi-nor to support JEDEC incompatible w25q128. Also by switching
to m25p80 we gain accelerated SPI flash reads.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49260
3c298f89-4303-0410-b956-
a3cf2f4a3e73
rmilecki [Tue, 26 Apr 2016 12:36:34 +0000 (12:36 +0000)]
bcm53xx: support JEDEC incompatible w25q128 in spi-nor
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49259
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Tue, 26 Apr 2016 11:44:36 +0000 (11:44 +0000)]
ar71xx: Add support for the OMYlink OMY-G1
https://wiki.openwrt.org/toh/omylink/omy-g1
http://www.omylink.com/
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49258
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Tue, 26 Apr 2016 11:44:29 +0000 (11:44 +0000)]
zynq: Add Zybo device support
Signed-off-by: Jason Wu <jason.wu.misc@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49257
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Tue, 26 Apr 2016 11:44:26 +0000 (11:44 +0000)]
Zynq: Add Zedboard device support
Tested-by: Joe Zhang <jz21082@gmail.com>
Signed-off-by: Jason Wu <jason.wu.misc@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49256
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Tue, 26 Apr 2016 11:44:22 +0000 (11:44 +0000)]
zynq: Remove rdinit patch
This is not required as long as CONFIG_TARGET_INIT_CMD is correctly
configured.
Signed-off-by: Jason Wu <jason.wu.misc@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49255
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Tue, 26 Apr 2016 11:44:17 +0000 (11:44 +0000)]
lantiq: use dwc2 by default on all ar9 boards
The dwc2 USB driver now works on Lantiq ar9, but the
default is still ltq-hcd-ar9. This patch switches to
dwc2 by default.
v2: all ar9 boards (v1 was just for BTHOMEHUBV3A and WBMR)
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49254
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Tue, 26 Apr 2016 11:44:13 +0000 (11:44 +0000)]
lantiq: install uboot-envtools by default on BTHOMEHUBV3A
The only way to access the u-boot console on the BTHOMEHUBV3A
is by soldering a serial console onto some really tiny pads.
To enable installation without soldering it would be helpful
to be able to modify the uboot environment from within
the ramdisk image used as part of the installation process.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49253
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Tue, 26 Apr 2016 11:44:10 +0000 (11:44 +0000)]
dnsmasq: run as dedicated UID/GID
Running dnsmasq in a dedicated user/group allows matching its outgoing
traffic more easily using iptables' owner match.
Add UID/GID to the package metadata and append the user/group
parameters to the init script.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49252
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Tue, 26 Apr 2016 11:44:07 +0000 (11:44 +0000)]
mac80211: ath9k: add GPIO support for AR9280 chip
Enable access to GPIO on Atheros wireless chip AR9280.
Support for 9280 is added to existing 9285/9287 subsystem
because these 3 chips differ only in number of GPIO pins.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49251
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Tue, 26 Apr 2016 11:44:03 +0000 (11:44 +0000)]
lantiq: remove read-only flag on two partitions on BTHOMEHUBV3A
Remove read-only flag on two partitions on BTHOMEHUBV3A:
uboot-config - otherwise fw_setenv command cannot be used.
ath9k-cal - so that ath9k calibration data can be copied
to the partition on a newly installed board.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49250
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Tue, 26 Apr 2016 11:44:00 +0000 (11:44 +0000)]
cns3xxx: set both MPS 'and' MRSS to 128
Fixes some DMA issues with this platform. Because this isn't currently accepted,
and can potentially disrupt other platforms (as read in commit log), I will
leave this cns3xxx specific.
Original Patch: https://patchwork.ozlabs.org/patch/600024/
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49249
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Tue, 26 Apr 2016 11:43:57 +0000 (11:43 +0000)]
cns3xxx: backport pci fix for cns3xxx_write_config
Fix is required to properly set pci config bits.
Original Patch: https://patchwork.ozlabs.org/patch/596170/
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49248
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Tue, 26 Apr 2016 11:43:53 +0000 (11:43 +0000)]
ramips: Add support for the Netgear WNDR3700v5
https://wiki.openwrt.org/toh/netgear/wndr3700
wndr3700v5 uses the single-core dual thread MediaTek MT7621S SoC.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49247
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Tue, 26 Apr 2016 11:43:49 +0000 (11:43 +0000)]
usbutils: Update USB IDs list and drop gzip compression
Change mirror to Github (Gentoo repo) and drop the gzip compression.
Worst case there's about 4kbyte increase in size but most images ends up
beign somewhere between 4-100kbyte smaller due to the lzma compression.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49246
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Tue, 26 Apr 2016 11:43:45 +0000 (11:43 +0000)]
ar71xx: Add TP-Link TL-WR740N v6 support to trunk
This patch adds support for the TP-Link TL-WR740N v6 into OpenWrt trunk. Hardware wise, it's very similar to the TL-WR841N v10. See the forum thread [1]. Credit goes to the user 'traveler' who did the legwork and tested builds.
Also thanks to Matthias Schiffer for clarifying the DEVICE_PROFILE settings.
Signed-off by: Stijn Segers <francesco.borromini@inventati.org>
[1]: https://forum.openwrt.org/viewtopic.php?pid=318704
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49245
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Tue, 26 Apr 2016 11:43:42 +0000 (11:43 +0000)]
ar71xx: simplify patch 613 and add missing error handling
Dynamic allocation of label can be simplified.
Also add error handling to deal with failed memory allocation.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49244
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Tue, 26 Apr 2016 11:43:38 +0000 (11:43 +0000)]
mediatek: update patches
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49243
3c298f89-4303-0410-b956-
a3cf2f4a3e73