ramips: add support for Planex MZK-EX300NP

MZK-EX300NP is MT7620A based wifi repeater.
Built-in power supply.
64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49235 3c298f89-4303-0410-b956-a3cf2f4a3e73

diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index 367801d..a263b52 100755 (executable)
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -119,7 +119,8 @@ dir-615-h1)
        ucidef_set_led_default "status" "Status LED (amber)" "$board:amber:status" "0"
        set_wifi_led "rt2800pci-phy0::radio"
        ;;
-dir-620-d1)
+dir-620-d1|\
+mzk-ex300np)
        set_wifi_led "$board:green:wifi"
        ;;
 dir-810l|\

diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index dc3d1bc..28fcc61 100755 (executable)
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -163,6 +163,7 @@ ramips_setup_interfaces()
        cs-qr10|\
        d105|\
        hpm|\
+       mzk-ex300np|\
        na930|\
        wli-tx4-ag300n|\
        wrh-300cr)

diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index 2d43f54..352357c 100644 (file)
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -155,6 +155,7 @@ get_status_led() {
        whr-600d)
                status_led="$board:orange:wifi"
                ;;
+       mzk-ex300np|\
        rt-n10-plus|\
        tew-691gr|\
        tew-692gr|\

diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index 73dd599..13d325d 100755 (executable)
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -295,6 +295,9 @@ ramips_board_detect() {
        *"MZK-DP150N")
                name="mzk-dp150n"
                ;;
+       *"MZK-EX300NP")
+               name="mzk-ex300np"
+               ;;
        *"MZK-W300NH2"*)
                name="mzk-w300nh2"
                ;;

diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index f153b02..522e78a 100755 (executable)
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -89,6 +89,7 @@ platform_check_image() {
        mt7628|\
        mzk-750dhp|\
        mzk-dp150n|\
+       mzk-ex300np|\
        mzk-w300nh2|\
        mzk-wdpr|\
        nbg-419n|\

diff --git a/target/linux/ramips/dts/MZK-EX300NP.dts b/target/linux/ramips/dts/MZK-EX300NP.dts
new file mode 100644 (file)
index 0000000..fd5c5cd
--- /dev/null
+++ b/target/linux/ramips/dts/MZK-EX300NP.dts
@@ -0,0 +1,132 @@
+/dts-v1/;
+
+/include/ "mt7620a.dtsi"
+
+/ {
+       compatible = "ralink,mt7620a-soc";
+       model = "Planex MZK-EX300NP";
+
+       palmbus@10000000 {
+               gpio1: gpio@638 {
+                       status = "okay";
+               };
+
+               gpio3: gpio@688 {
+                       status = "okay";
+               };
+
+               spi@b00 {
+                       status = "okay";
+
+                       m25p80@0 {
+                               #address-cells = <1>;
+                               #size-cells = <1>;
+                               compatible = "jedec,spi-nor";
+                               reg = <0 0>;
+                               linux,modalias = "m25p80", "w25q64";
+                               spi-max-frequency = <10000000>;
+
+                               partition@0 {
+                                       label = "u-boot";
+                                       reg = <0x0 0x30000>;
+                                       read-only;
+                               };
+
+                               partition@30000 {
+                                       label = "u-boot-env";
+                                       reg = <0x30000 0x10000>;
+                                       read-only;
+                               };
+
+                               factory: partition@40000 {
+                                       label = "factory";
+                                       reg = <0x40000 0x10000>;
+                                       read-only;
+                               };
+
+                               partition@50000 {
+                                       label = "firmware";
+                                       reg = <0x50000 0x730000>;
+                               };
+
+                               partition@780000 {
+                                       label = "Udata";
+                                       reg = <0x780000 0x80000>;
+                               };
+                       };
+               };
+       };
+
+       pinctrl {
+               state_default: pinctrl0 {
+                       gpio {
+                               ralink,group = "i2c", "spi refclk", "rgmii1", "wled";
+                               ralink,function = "gpio";
+                       };
+               };
+       };
+
+       ethernet@10100000 {
+               pinctrl-names = "default";
+               pinctrl-0 = <&ephy_pins>;
+               mtd-mac-address = <&factory 0x4>;
+               mediatek,portmap = "llllw";
+       };
+
+       wmac@10180000 {
+               ralink,mtd-eeprom = <&factory 0>;
+       };
+
+       gpio-leds {
+               compatible = "gpio-leds";
+
+               wifi {
+                       label = "mzk-ex300np:green:wifi";
+                       gpios = <&gpio3 0 1>;
+               };
+
+               wps {
+                       label = "mzk-ex300np:green:wps";
+                       gpios = <&gpio1 5 1>;
+               };
+
+               rep {
+                       label = "mzk-ex300np:blue:rep";
+                       gpios = <&gpio1 4 1>;
+               };
+
+               wifi1 {
+                       label = "mzk-ex300np:blue:wifi1";
+                       gpios = <&gpio1 1 1>;
+               };
+
+               wifi2 {
+                       label = "mzk-ex300np:blue:wifi2";
+                       gpios = <&gpio1 2 1>;
+               };
+
+               wifi3 {
+                       label = "mzk-ex300np:blue:wifi3";
+                       gpios = <&gpio1 0 1>;
+               };
+       };
+
+       gpio-keys-polled {
+               compatible = "gpio-keys-polled";
+               #address-cells = <1>;
+               #size-cells = <0>;
+               poll-interval = <20>;
+
+               reset {
+                       label = "reset";
+                       gpios = <&gpio0 1 1>;
+                       linux,code = <0x198>;
+               };
+
+               wps {
+                       label = "wps";
+                       gpios = <&gpio1 3 0>;
+                       linux,code = <0x211>;
+               };
+       };
+};

diff --git a/target/linux/ramips/image/mt7620.mk b/target/linux/ramips/image/mt7620.mk
index d742151..35cb46a 100644 (file)
--- a/target/linux/ramips/image/mt7620.mk
+++ b/target/linux/ramips/image/mt7620.mk
@@ -101,6 +101,7 @@ na930_mtd_size=20971520
 Image/Build/Profile/NA930=$(call BuildFirmware/CustomFlash/$(1),$(1),na930,NA930,$(na930_mtd_size))
 Image/Build/Profile/DB-WRT01=$(call BuildFirmware/Default8M/$(1),$(1),db-wrt01,DB-WRT01)
 Image/Build/Profile/MZK-750DHP=$(call BuildFirmware/Default8M/$(1),$(1),mzk-750dhp,MZK-750DHP)
+Image/Build/Profile/MZK-EX300NP=$(call BuildFirmware/Default8M/$(1),$(1),mzk-ex300np,MZK-EX300NP)
 Image/Build/Profile/HC5661=$(call BuildFirmware/Default16M/$(1),$(1),hc5661,HC5661)
 Image/Build/Profile/HC5761=$(call BuildFirmware/Default16M/$(1),$(1),hc5761,HC5761)
 Image/Build/Profile/HC5861=$(call BuildFirmware/Default16M/$(1),$(1),hc5861,HC5861)
@@ -147,6 +148,7 @@ define Image/Build/Profile/Default
        $(call Image/Build/Profile/WHR1166D,$(1))
        $(call Image/Build/Profile/DB-WRT01,$(1))
        $(call Image/Build/Profile/MZK-750DHP,$(1))
+       $(call Image/Build/Profile/MZK-EX300NP,$(1))
        $(call Image/Build/Profile/NA930,$(1))
        $(call Image/Build/Profile/HC5661,$(1))
        $(call Image/Build/Profile/HC5761,$(1))

diff --git a/target/linux/ramips/mt7620/profiles/planex.mk b/target/linux/ramips/mt7620/profiles/planex.mk
index 15560ab..157cf8d 100644 (file)
--- a/target/linux/ramips/mt7620/profiles/planex.mk
+++ b/target/linux/ramips/mt7620/profiles/planex.mk
@@ -28,3 +28,14 @@ define Profile/MZK-750DHP/Description
        Package set optimized for the Planex MZK-750DHP.
 endef
 $(eval $(call Profile,MZK-750DHP))
+
+
+define Profile/MZK-EX300NP
+       NAME:=Planex MZK-EX300NP
+       PACKAGES:=
+endef
+
+define Profile/MZK-EX300NP/Description
+       Package set optimized for the Planex MZK-EX300NP.
+endef
+$(eval $(call Profile,MZK-EX300NP))