{
.desc = "sw4",
.type = EV_KEY,
- .code = BTN_0,
+ .code = KEY_RESTART,
.threshold = 3,
.gpio = UBNT_RS_GPIO_SW4,
.active_low = 1,
{
.desc = "reset",
.type = EV_KEY,
- .code = BTN_0,
+ .code = KEY_RESTART,
.threshold = 3,
.gpio = UBNT_M_GPIO_BTN_RESET,
.active_low = 1,
pb42_pci_init();
}
+/*
+ * There is Secondary MAC address duplicate problem with some UBNT HW batches.
+ * Do not increase Secondary MAC address by 1 but do workaround
+ * with 'Locally Administrated' bit.
+ */
+static void __init ubnt_init_secondary_mac(unsigned char *mac_base)
+{
+ ar71xx_init_mac(ar71xx_eth1_data.mac_addr, mac_base, 0);
+ ar71xx_eth1_data.mac_addr[0] |= 0x02;
+}
+
#define UBNT_RS_WAN_PHYMASK (1 << 20)
#define UBNT_RS_LAN_PHYMASK ((1 << 16) | (1 << 17) | (1 << 18) | (1 << 19))
-#define UBNT_RSPRO_WAN_PHYMASK (1 << 4)
-#define UBNT_RSPRO_LAN_PHYMASK ((1 << 0) | (1 << 1) | (1 << 2) | (1 << 3))
-
static void __init ubnt_rs_setup(void)
{
ubnt_generic_setup();
ar71xx_add_device_mdio(~(UBNT_RS_WAN_PHYMASK | UBNT_RS_LAN_PHYMASK));
+ ar71xx_init_mac(ar71xx_eth0_data.mac_addr, ar71xx_mac_base, 0);
ar71xx_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
ar71xx_eth0_data.phy_mask = UBNT_RS_WAN_PHYMASK;
+ ubnt_init_secondary_mac(ar71xx_mac_base);
ar71xx_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_RMII;
- ar71xx_eth1_data.phy_mask = UBNT_RS_LAN_PHYMASK;
-
ar71xx_eth1_data.speed = SPEED_100;
ar71xx_eth1_data.duplex = DUPLEX_FULL;
MIPS_MACHINE(AR71XX_MACH_UBNT_RS, "UBNT-RS", "Ubiquiti RouterStation",
ubnt_rs_setup);
-MIPS_MACHINE(AR71XX_MACH_UBNT_AR71XX, "Ubiquiti AR71xx-based board",
- "Ubiquiti RouterStation", ubnt_rs_setup);
+#define UBNT_RSPRO_WAN_PHYMASK (1 << 4)
+#define UBNT_RSPRO_LAN_PHYMASK ((1 << 0) | (1 << 1) | (1 << 2) | (1 << 3))
static void __init ubnt_rspro_setup(void)
{
ubnt_generic_setup();
- ar71xx_add_device_mdio(~(UBNT_RSPRO_WAN_PHYMASK | UBNT_RSPRO_LAN_PHYMASK));
+ ar71xx_add_device_mdio(~(UBNT_RSPRO_WAN_PHYMASK |
+ UBNT_RSPRO_LAN_PHYMASK));
+ ar71xx_init_mac(ar71xx_eth0_data.mac_addr, ar71xx_mac_base, 0);
ar71xx_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
ar71xx_eth0_data.phy_mask = UBNT_RSPRO_WAN_PHYMASK;
+ ubnt_init_secondary_mac(ar71xx_mac_base);
ar71xx_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
ar71xx_eth1_data.phy_mask = UBNT_RSPRO_LAN_PHYMASK;
-
ar71xx_eth1_data.speed = SPEED_1000;
ar71xx_eth1_data.duplex = DUPLEX_FULL;
ar71xx_add_device_mdio(~UBNT_LSSR71_PHY_MASK);
+ ar71xx_init_mac(ar71xx_eth0_data.mac_addr, ar71xx_mac_base, 0);
ar71xx_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
ar71xx_eth0_data.phy_mask = UBNT_LSSR71_PHY_MASK;
static void __init ubnt_m_setup(void)
{
- u8 *mac = (u8 *) KSEG1ADDR(0x1fff0000);
+ u8 *mac1 = (u8 *) KSEG1ADDR(0x1fff0000);
+ u8 *mac2 = (u8 *) KSEG1ADDR(0x1fff0000 + ETH_ALEN);
u8 *ee = (u8 *) KSEG1ADDR(0x1fff1000);
- ar71xx_set_mac_base(mac);
-
ar71xx_add_device_m25p80(NULL);
ar71xx_add_device_mdio(~0);
+ ar71xx_init_mac(ar71xx_eth0_data.mac_addr, mac1, 0);
+ ar71xx_init_mac(ar71xx_eth1_data.mac_addr, mac2, 0);
ar71xx_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
- ar71xx_eth0_data.phy_mask = 0;
ar71xx_eth0_data.speed = SPEED_100;
ar71xx_eth0_data.duplex = DUPLEX_FULL;
ar71xx_eth0_data.fifo_cfg1 = 0x0010ffff;
{
ubnt_m_setup();
+ ar71xx_eth1_data.has_ar7240_switch = 1;
ar71xx_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_RMII;
- ar71xx_eth1_data.phy_mask = 0;
ar71xx_eth1_data.speed = SPEED_1000;
ar71xx_eth1_data.duplex = DUPLEX_FULL;
ar71xx_eth1_data.fifo_cfg1 = 0x0010ffff;
MIPS_MACHINE(AR71XX_MACH_UBNT_NANO_M, "UBNT-NM", "Ubiquiti Nanostation M",
ubnt_nano_m_setup);
+
+static struct gpio_led ubnt_unifi_leds_gpio[] __initdata = {
+ {
+ .name = "ubnt:orange:dome",
+ .gpio = 1,
+ .active_low = 0,
+ }, {
+ .name = "ubnt:green:dome",
+ .gpio = 0,
+ .active_low = 0,
+ }
+};
+
+static void __init ubnt_unifi_setup(void)
+{
+ u8 *mac = (u8 *) KSEG1ADDR(0x1fff0000);
+ u8 *ee = (u8 *) KSEG1ADDR(0x1fff1000);
+
+ ar71xx_add_device_m25p80(NULL);
+
+ ar71xx_add_device_mdio(~0);
+
+ ar71xx_init_mac(ar71xx_eth0_data.mac_addr, mac, 0);
+ ar71xx_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
+ ar71xx_eth0_data.speed = SPEED_100;
+ ar71xx_eth0_data.duplex = DUPLEX_FULL;
+
+ ar71xx_add_device_eth(0);
+
+ ap91_pci_init(ee, NULL);
+
+ ar71xx_add_device_leds_gpio(-1, ARRAY_SIZE(ubnt_unifi_leds_gpio),
+ ubnt_unifi_leds_gpio);
+}
+
+MIPS_MACHINE(AR71XX_MACH_UBNT_UNIFI, "UBNT-XM", "Ubiquiti UniFi",
+ ubnt_unifi_setup);