msgid "Advanced Settings"
msgstr ""
+msgid "Allow gateways with NAT"
+msgstr ""
+
+msgid "Allow the selection of an outgoing ipv4 gateway with NAT"
+msgstr ""
+
+msgid "Announce uplink"
+msgstr ""
+
msgid "Announced network"
msgstr "Announced network"
+msgid "Both values must use the dotted decimal notation."
+msgstr ""
+
msgid "Broadcast address"
msgstr ""
msgid "Device"
msgstr ""
+msgid "Display"
+msgstr ""
+
msgid "Downlink"
msgstr ""
msgid "Enable"
msgstr ""
+msgid ""
+"Enable SmartGateway. If it is disabled, then all other SmartGateway "
+"parameters are ignored. Default is \"no\"."
+msgstr ""
+
msgid "Enable this interface."
msgstr ""
msgid "HNA"
msgstr ""
+msgid "HNA Announcements"
+msgstr ""
+
msgid "HNA interval"
msgstr "HNA interval"
msgid "Hello validity time"
msgstr "Hello validity time"
+msgid "Hna4"
+msgstr ""
+
+msgid "Hna6"
+msgstr ""
+
msgid "Hops"
msgstr ""
"multicast."
msgstr ""
+msgid ""
+"IPv6 network must be given in full notation, prefix must be in CIDR notation."
+msgstr ""
+
msgid "IPv6 source"
msgstr ""
"of a not-linklocal interface IP."
msgstr ""
+msgid "IPv6-Prefix of the uplink"
+msgstr ""
+
msgid ""
"If the route to the current gateway is to be changed, the ETX value of this "
"gateway is multiplied with this value before it is compared to the new one. "
"with the etx_ffeth metric!<br />Defaults to \"1.0\"."
msgstr ""
+msgid ""
+"If this Node uses NAT for connections to the internet. Default is \"yes\"."
+msgstr ""
+
msgid "Interface"
msgstr ""
msgid "Neighbour IP"
msgstr "Neighbour IP"
+msgid "Neighbours"
+msgstr ""
+
msgid "Netmask"
msgstr "Netmask"
msgid "Nodes"
msgstr ""
+msgid "OLSR"
+msgstr ""
+
+msgid "OLSR - Display Options"
+msgstr ""
+
msgid "OLSR - HNA-Announcements"
msgstr "OLSR - HNA-Announcements"
msgid "Prefix"
msgstr "Prefix"
-msgid "Routen"
+msgid "Resolve"
+msgstr ""
+
+msgid ""
+"Resolve hostnames on status pages. It is generally safe to allow this, but "
+"if you use public IPs and have unstable DNS-Setup then those pages will load "
+"really slow. In this case disable it here."
+msgstr ""
+
+msgid "Routes"
msgstr ""
msgid "Secondary OLSR interfaces"
"IP of the first interface."
msgstr ""
+msgid "SmartGW"
+msgstr ""
+
msgid "SmartGW announcements"
msgstr ""
+msgid "SmartGateway is not configured on this system."
+msgstr ""
+
msgid "Source address"
msgstr ""
+msgid ""
+"Specifies the speed of the uplink in kilobits/s. First parameter is "
+"upstream, second parameter is downstream. Default is \"128 1024\"."
+msgstr ""
+
+msgid "Speed of the uplink"
+msgstr ""
+
msgid "State"
msgstr ""
"It can have a value between 1 and 65535."
msgstr ""
+msgid ""
+"This can be used to signal the external IPv6 prefix of the uplink to the "
+"clients. This might allow a client to change it's local IPv6 address to use "
+"the IPv6 gateway without any kind of address translation. The maximum prefix "
+"length is 64 bits. Default is \"::/0\" (no prefix)."
+msgstr ""
+
msgid "Timing and Validity"
msgstr ""
-msgid "Topologie"
+msgid "Topology"
msgstr ""
msgid ""
msgid "Uplink"
msgstr ""
+msgid "Uplink uses NAT"
+msgstr ""
+
msgid "Use hysteresis"
msgstr "Use hysteresis"
msgid "WLAN"
msgstr ""
+msgid ""
+"Warning: kmod-ipip is not installed. Without kmod-ipip SmartGateway will not "
+"work, please install it."
+msgstr ""
+
msgid "Weight"
msgstr ""
"instead."
msgstr ""
+msgid ""
+"Which kind of uplink is exported to the other mesh nodes. An uplink is "
+"detected by looking for a local HNA of 0.0.0.0/0, ::ffff:0:0/96 or 2000::/3. "
+"Default setting is \"both\"."
+msgstr ""
+
msgid "Willingness"
msgstr "Willingness"