/*
* Ubiquiti RouterStation support
*
- * Copyright (C) 2008 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2008-2009 Gabor Juhos <juhosg@openwrt.org>
* Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
* Copyright (C) 2008 Ubiquiti <support@ubnt.com>
*
* by the Free Software Foundation.
*/
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/flash.h>
-#include <linux/input.h>
-
-#include <asm/mips_machine.h>
#include <asm/mach-ar71xx/ar71xx.h>
-#include <asm/mach-ar71xx/pci.h>
-#include <asm/mach-ar71xx/platform.h>
+
+#include "machtype.h"
+#include "devices.h"
+#include "dev-m25p80.h"
+#include "dev-ap91-pci.h"
+#include "dev-gpio-buttons.h"
+#include "dev-pb42-pci.h"
+#include "dev-leds-gpio.h"
+#include "dev-usb.h"
#define UBNT_RS_GPIO_LED_RF 2
#define UBNT_RS_GPIO_SW4 8
-#define UBNT_BUTTONS_POLL_INTERVAL 20
+#define UBNT_LS_SR71_GPIO_LED_D25 0
+#define UBNT_LS_SR71_GPIO_LED_D26 1
+#define UBNT_LS_SR71_GPIO_LED_D24 2
+#define UBNT_LS_SR71_GPIO_LED_D23 4
+#define UBNT_LS_SR71_GPIO_LED_D22 5
+#define UBNT_LS_SR71_GPIO_LED_D27 6
+#define UBNT_LS_SR71_GPIO_LED_D28 7
+
+#define UBNT_M_GPIO_LED_L1 0
+#define UBNT_M_GPIO_LED_L2 1
+#define UBNT_M_GPIO_LED_L3 11
+#define UBNT_M_GPIO_LED_L4 7
+#define UBNT_M_GPIO_BTN_RESET 12
-static struct spi_board_info ubnt_rs_spi_info[] = {
+#define UBNT_KEYS_POLL_INTERVAL 20 /* msecs */
+#define UBNT_KEYS_DEBOUNCE_INTERVAL (3 * UBNT_KEYS_POLL_INTERVAL)
+
+static struct gpio_led ubnt_rs_leds_gpio[] __initdata = {
{
- .bus_num = 0,
- .chip_select = 0,
- .max_speed_hz = 25000000,
- .modalias = "m25p80",
+ .name = "ubnt:green:rf",
+ .gpio = UBNT_RS_GPIO_LED_RF,
+ .active_low = 0,
}
};
-static struct ar71xx_pci_irq ubnt_rs_pci_irqs[] __initdata = {
+static struct gpio_led ubnt_ls_sr71_leds_gpio[] __initdata = {
{
- .slot = 0,
- .pin = 1,
- .irq = AR71XX_PCI_IRQ_DEV0,
+ .name = "ubnt:green:d22",
+ .gpio = UBNT_LS_SR71_GPIO_LED_D22,
+ .active_low = 0,
+ }, {
+ .name = "ubnt:green:d23",
+ .gpio = UBNT_LS_SR71_GPIO_LED_D23,
+ .active_low = 0,
+ }, {
+ .name = "ubnt:green:d24",
+ .gpio = UBNT_LS_SR71_GPIO_LED_D24,
+ .active_low = 0,
+ }, {
+ .name = "ubnt:red:d25",
+ .gpio = UBNT_LS_SR71_GPIO_LED_D25,
+ .active_low = 0,
+ }, {
+ .name = "ubnt:red:d26",
+ .gpio = UBNT_LS_SR71_GPIO_LED_D26,
+ .active_low = 0,
}, {
- .slot = 1,
- .pin = 1,
- .irq = AR71XX_PCI_IRQ_DEV1,
+ .name = "ubnt:green:d27",
+ .gpio = UBNT_LS_SR71_GPIO_LED_D27,
+ .active_low = 0,
}, {
- .slot = 2,
- .pin = 1,
- .irq = AR71XX_PCI_IRQ_DEV2,
+ .name = "ubnt:green:d28",
+ .gpio = UBNT_LS_SR71_GPIO_LED_D28,
+ .active_low = 0,
}
};
-static struct gpio_led ubnt_rs_leds_gpio[] __initdata = {
+static struct gpio_led ubnt_m_leds_gpio[] __initdata = {
{
- .name = "ubnt:green:rf",
- .gpio = UBNT_RS_GPIO_LED_RF,
+ .name = "ubnt:red:link1",
+ .gpio = UBNT_M_GPIO_LED_L1,
+ .active_low = 0,
+ }, {
+ .name = "ubnt:orange:link2",
+ .gpio = UBNT_M_GPIO_LED_L2,
+ .active_low = 0,
+ }, {
+ .name = "ubnt:green:link3",
+ .gpio = UBNT_M_GPIO_LED_L3,
+ .active_low = 0,
+ }, {
+ .name = "ubnt:green:link4",
+ .gpio = UBNT_M_GPIO_LED_L4,
.active_low = 0,
}
};
-static struct gpio_button ubnt_rs_gpio_buttons[] __initdata = {
+static struct gpio_keys_button ubnt_gpio_keys[] __initdata = {
{
.desc = "sw4",
.type = EV_KEY,
- .code = BTN_0,
- .threshold = 5,
+ .code = KEY_RESTART,
+ .debounce_interval = UBNT_KEYS_DEBOUNCE_INTERVAL,
.gpio = UBNT_RS_GPIO_SW4,
.active_low = 1,
}
};
-#define UBNT_RS_WAN_PHYMASK (1 << 20)
-#define UBNT_RS_LAN_PHYMASK ((1 << 16) | (1 << 17) | (1 << 18) | (1 << 19))
+static struct gpio_keys_button ubnt_m_gpio_keys[] __initdata = {
+ {
+ .desc = "reset",
+ .type = EV_KEY,
+ .code = KEY_RESTART,
+ .debounce_interval = UBNT_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = UBNT_M_GPIO_BTN_RESET,
+ .active_low = 1,
+ }
+};
+
+static const char *ubnt_part_probes[] = {
+ "RedBoot",
+ NULL,
+};
+
+static struct flash_platform_data ubnt_flash_data = {
+ .part_probes = ubnt_part_probes,
+};
+
+static void __init ubnt_generic_setup(void)
+{
+ ar71xx_add_device_m25p80(&ubnt_flash_data);
+
+ ar71xx_register_gpio_keys_polled(-1, UBNT_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(ubnt_gpio_keys),
+ ubnt_gpio_keys);
+
+ pb42_pci_init();
+}
+
+/*
+ * There is Secondary MAC address duplicate problem with some UBNT HW batches.
+ * Do not increase Secondary MAC address by 1 but do workaround
+ * with 'Locally Administrated' bit.
+ */
+static void __init ubnt_init_secondary_mac(unsigned char *mac_base)
+{
+ ar71xx_init_mac(ar71xx_eth1_data.mac_addr, mac_base, 0);
+ ar71xx_eth1_data.mac_addr[0] |= 0x02;
+}
+
+#define UBNT_RS_WAN_PHYMASK BIT(20)
+#define UBNT_RS_LAN_PHYMASK (BIT(16) | BIT(17) | BIT(18) | BIT(19))
static void __init ubnt_rs_setup(void)
{
- ar71xx_add_device_spi(NULL, ubnt_rs_spi_info,
- ARRAY_SIZE(ubnt_rs_spi_info));
+ ubnt_generic_setup();
- ar71xx_add_device_mdio(~(UBNT_RS_WAN_PHYMASK | UBNT_RS_LAN_PHYMASK));
+ ar71xx_add_device_mdio(0, ~(UBNT_RS_WAN_PHYMASK | UBNT_RS_LAN_PHYMASK));
+ ar71xx_init_mac(ar71xx_eth0_data.mac_addr, ar71xx_mac_base, 0);
ar71xx_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
ar71xx_eth0_data.phy_mask = UBNT_RS_WAN_PHYMASK;
+ ubnt_init_secondary_mac(ar71xx_mac_base);
ar71xx_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_RMII;
- ar71xx_eth1_data.phy_mask = UBNT_RS_LAN_PHYMASK;
-
ar71xx_eth1_data.speed = SPEED_100;
ar71xx_eth1_data.duplex = DUPLEX_FULL;
ar71xx_add_device_usb();
- ar71xx_pci_init(ARRAY_SIZE(ubnt_rs_pci_irqs), ubnt_rs_pci_irqs);
+ ar71xx_add_device_leds_gpio(-1, ARRAY_SIZE(ubnt_rs_leds_gpio),
+ ubnt_rs_leds_gpio);
+}
+
+MIPS_MACHINE(AR71XX_MACH_UBNT_RS, "UBNT-RS", "Ubiquiti RouterStation",
+ ubnt_rs_setup);
+
+#define UBNT_RSPRO_WAN_PHYMASK BIT(4)
+#define UBNT_RSPRO_LAN_PHYMASK (BIT(0) | BIT(1) | BIT(2) | BIT(3))
+
+static void __init ubnt_rspro_setup(void)
+{
+ ubnt_generic_setup();
+
+ ar71xx_add_device_mdio(0, ~(UBNT_RSPRO_WAN_PHYMASK |
+ UBNT_RSPRO_LAN_PHYMASK));
+
+ ar71xx_init_mac(ar71xx_eth0_data.mac_addr, ar71xx_mac_base, 0);
+ ar71xx_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
+ ar71xx_eth0_data.phy_mask = UBNT_RSPRO_WAN_PHYMASK;
+
+ ubnt_init_secondary_mac(ar71xx_mac_base);
+ ar71xx_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
+ ar71xx_eth1_data.phy_mask = UBNT_RSPRO_LAN_PHYMASK;
+ ar71xx_eth1_data.speed = SPEED_1000;
+ ar71xx_eth1_data.duplex = DUPLEX_FULL;
+
+ ar71xx_add_device_eth(0);
+ ar71xx_add_device_eth(1);
+
+ ar71xx_add_device_usb();
ar71xx_add_device_leds_gpio(-1, ARRAY_SIZE(ubnt_rs_leds_gpio),
ubnt_rs_leds_gpio);
+}
+
+MIPS_MACHINE(AR71XX_MACH_UBNT_RSPRO, "UBNT-RSPRO", "Ubiquiti RouterStation Pro",
+ ubnt_rspro_setup);
+
+static void __init ubnt_lsx_setup(void)
+{
+ ubnt_generic_setup();
+}
+
+MIPS_MACHINE(AR71XX_MACH_UBNT_LSX, "UBNT-LSX", "Ubiquiti LSX", ubnt_lsx_setup);
+
+#define UBNT_LSSR71_PHY_MASK BIT(1)
+
+static void __init ubnt_lssr71_setup(void)
+{
+ ubnt_generic_setup();
+
+ ar71xx_add_device_mdio(0, ~UBNT_LSSR71_PHY_MASK);
+
+ ar71xx_init_mac(ar71xx_eth0_data.mac_addr, ar71xx_mac_base, 0);
+ ar71xx_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
+ ar71xx_eth0_data.phy_mask = UBNT_LSSR71_PHY_MASK;
+
+ ar71xx_add_device_eth(0);
+
+ ar71xx_add_device_leds_gpio(-1, ARRAY_SIZE(ubnt_ls_sr71_leds_gpio),
+ ubnt_ls_sr71_leds_gpio);
+}
+
+MIPS_MACHINE(AR71XX_MACH_UBNT_LSSR71, "UBNT-LS-SR71", "Ubiquiti LS-SR71",
+ ubnt_lssr71_setup);
+
+#define UBNT_M_WAN_PHYMASK BIT(4)
+
+static void __init ubnt_m_setup(void)
+{
+ u8 *mac1 = (u8 *) KSEG1ADDR(0x1fff0000);
+ u8 *mac2 = (u8 *) KSEG1ADDR(0x1fff0000 + ETH_ALEN);
+ u8 *ee = (u8 *) KSEG1ADDR(0x1fff1000);
+
+ ar71xx_add_device_m25p80(NULL);
+
+ ar71xx_add_device_mdio(0, ~UBNT_M_WAN_PHYMASK);
+
+ ar71xx_init_mac(ar71xx_eth0_data.mac_addr, mac1, 0);
+ ar71xx_init_mac(ar71xx_eth1_data.mac_addr, mac2, 0);
+ ar71xx_add_device_eth(0);
+
+ ap91_pci_init(ee, NULL);
+
+ ar71xx_add_device_leds_gpio(-1, ARRAY_SIZE(ubnt_m_leds_gpio),
+ ubnt_m_leds_gpio);
+
+ ar71xx_register_gpio_keys_polled(-1, UBNT_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(ubnt_m_gpio_keys),
+ ubnt_m_gpio_keys);
+}
+
+static void __init ubnt_rocket_m_setup(void)
+{
+ ubnt_m_setup();
+ ar71xx_add_device_usb();
+}
+
+MIPS_MACHINE(AR71XX_MACH_UBNT_BULLET_M, "UBNT-BM", "Ubiquiti Bullet M",
+ ubnt_m_setup);
+MIPS_MACHINE(AR71XX_MACH_UBNT_ROCKET_M, "UBNT-RM", "Ubiquiti Rocket M",
+ ubnt_rocket_m_setup);
+
+/* TODO detect the second ethernet port and use one
+ init function for all Ubiquiti MIMO series products */
+static void __init ubnt_nano_m_setup(void)
+{
+ ubnt_m_setup();
+ ar71xx_add_device_eth(1);
+}
+
+MIPS_MACHINE(AR71XX_MACH_UBNT_NANO_M, "UBNT-NM", "Ubiquiti Nanostation M",
+ ubnt_nano_m_setup);
+
+static struct gpio_led ubnt_airrouter_leds_gpio[] __initdata = {
+ {
+ .name = "ubnt:green:globe",
+ .gpio = 0,
+ .active_low = 1,
+ }
+};
+
+static void __init ubnt_airrouter_setup(void)
+{
+ u8 *mac1 = (u8 *) KSEG1ADDR(0x1fff0000);
+ u8 *ee = (u8 *) KSEG1ADDR(0x1fff1000);
+
+ ar71xx_add_device_m25p80(NULL);
+ ar71xx_add_device_mdio(0, ~UBNT_M_WAN_PHYMASK);
+
+ ar71xx_init_mac(ar71xx_eth0_data.mac_addr, mac1, 0);
+ ubnt_init_secondary_mac(mac1);
+
+ ar71xx_add_device_eth(1);
+ ar71xx_add_device_eth(0);
+ ar71xx_add_device_usb();
+
+ ap91_pci_init(ee, NULL);
+ ar71xx_add_device_leds_gpio(-1, ARRAY_SIZE(ubnt_airrouter_leds_gpio),
+ ubnt_airrouter_leds_gpio);
+}
+
+MIPS_MACHINE(AR71XX_MACH_UBNT_AIRROUTER, "UBNT-AR", "Ubiquiti AirRouter",
+ ubnt_airrouter_setup);
+
+static struct gpio_led ubnt_unifi_leds_gpio[] __initdata = {
+ {
+ .name = "ubnt:orange:dome",
+ .gpio = 1,
+ .active_low = 0,
+ }, {
+ .name = "ubnt:green:dome",
+ .gpio = 0,
+ .active_low = 0,
+ }
+};
+
+static void __init ubnt_unifi_setup(void)
+{
+ u8 *mac = (u8 *) KSEG1ADDR(0x1fff0000);
+ u8 *ee = (u8 *) KSEG1ADDR(0x1fff1000);
+
+ ar71xx_add_device_m25p80(NULL);
+
+ ar71xx_add_device_mdio(0, ~UBNT_M_WAN_PHYMASK);
+
+ ar71xx_init_mac(ar71xx_eth0_data.mac_addr, mac, 0);
+ ar71xx_add_device_eth(0);
+
+ ap91_pci_init(ee, NULL);
- ar71xx_add_device_gpio_buttons(-1, UBNT_BUTTONS_POLL_INTERVAL,
- ARRAY_SIZE(ubnt_rs_gpio_buttons),
- ubnt_rs_gpio_buttons);
+ ar71xx_add_device_leds_gpio(-1, ARRAY_SIZE(ubnt_unifi_leds_gpio),
+ ubnt_unifi_leds_gpio);
}
-MIPS_MACHINE(AR71XX_MACH_UBNT_RS, "Ubiquiti RouterStation", ubnt_rs_setup);
+MIPS_MACHINE(AR71XX_MACH_UBNT_UNIFI, "UBNT-XM", "Ubiquiti UniFi",
+ ubnt_unifi_setup);