2 * Copyright (C) 2009, Lars-Peter Clausen <lars@metafoo.de>
3 * N526 eBook reader support
5 * This program is free software; you can redistribute it and/or modify it
6 * under the terms of the GNU General Public License as published by the
7 * Free Software Foundation; either version 2 of the License, or (at your
8 * option) any later version.
10 * You should have received a copy of the GNU General Public License along
11 * with this program; if not, write to the Free Software Foundation, Inc.,
12 * 675 Mass Ave, Cambridge, MA 02139, USA.
16 #include <linux/kernel.h>
17 #include <linux/init.h>
18 #include <linux/gpio.h>
20 #include <asm/mach-jz4740/platform.h>
22 #include <linux/mtd/jz4740_nand.h>
23 #include <linux/jz4740_fb.h>
24 #include <linux/power_supply.h>
25 #include <linux/mmc/jz4740_mmc.h>
27 #include <video/broadsheetfb.h>
28 #include <linux/delay.h>
29 #include <linux/interrupt.h>
31 #include <linux/input.h>
32 #include <linux/gpio_keys.h>
34 #include <linux/i2c.h>
35 #include <linux/i2c-gpio.h>
40 static struct nand_ecclayout n526_ecclayout = {
43 6, 7, 8, 9, 10, 11, 12, 13,
44 14, 15, 16, 17, 18, 19, 20, 21,
45 22, 23, 24, 25, 26, 27, 28, 29,
46 30, 31, 32, 33, 34, 35, 36, 37,
55 static struct mtd_partition n526_partitions[] = {
56 { .name = "NAND BOOT partition",
57 .offset = 0 * 0x100000,
60 { .name = "NAND KERNEL partition",
61 .offset = 4 * 0x100000,
64 { .name = "NAND ROOTFS partition",
65 .offset = 16 * 0x100000,
66 .size = 498 * 0x100000,
70 static struct jz_nand_platform_data n526_nand_pdata = {
71 .ecc_layout = &n526_ecclayout,
72 .partitions = n526_partitions,
73 .num_partitions = ARRAY_SIZE(n526_partitions),
77 static struct jz4740_mmc_platform_data n526_mmc_pdata = {
78 .gpio_card_detect = JZ_GPIO_PORTD(7),
79 .card_detect_active_low = 1,
81 .gpio_power = JZ_GPIO_PORTD(17),
82 .power_active_low = 1,
85 static struct gpio_led n526_leds[] = {
87 .name = "n526:blue:power",
88 .gpio = JZ_GPIO_PORTD(28),
89 .default_state = LEDS_GPIO_DEFSTATE_ON,
93 static struct gpio_led_platform_data n526_leds_pdata = {
95 .num_leds = ARRAY_SIZE(n526_leds),
98 static struct platform_device n526_leds_device = {
102 .platform_data = &n526_leds_pdata,
106 static void __init board_gpio_setup(void)
108 /* We only need to enable/disable pullup here for pins used in generic
109 * drivers. Everything else is done by the drivers themselfs. */
110 jz_gpio_disable_pullup(JZ_GPIO_PORTD(17));
111 jz_gpio_enable_pullup(JZ_GPIO_PORTD(7));
112 jz_gpio_disable_pullup(JZ_GPIO_PORTC(19));
113 jz_gpio_disable_pullup(JZ_GPIO_PORTC(20));
114 jz_gpio_disable_pullup(JZ_GPIO_PORTC(21));
115 jz_gpio_disable_pullup(JZ_GPIO_PORTC(23));
119 static const int n526_eink_ctrl_gpios[] = {
126 static void n526_eink_set_ctl(struct broadsheetfb_par * par, unsigned char ctrl, u8
129 gpio_set_value(n526_eink_ctrl_gpios[ctrl], value);
133 static int n526_eink_wait(struct broadsheetfb_par *par)
135 wait_event(par->waitq, gpio_get_value(JZ_GPIO_PORTB(17)));
140 static u16 n526_eink_get_hdb(struct broadsheetfb_par *par)
143 jz_gpio_port_direction_input(JZ_GPIO_PORTC(0), 0xffff);
144 gpio_set_value(JZ_GPIO_PORTC(21), 0);
147 value = jz_gpio_port_get_value(JZ_GPIO_PORTC(0), 0xffff);
149 gpio_set_value(JZ_GPIO_PORTC(21), 1);
150 jz_gpio_port_direction_output(JZ_GPIO_PORTC(0), 0xffff);
154 static void n526_eink_set_hdb(struct broadsheetfb_par *par, u16 value)
156 jz_gpio_port_set_value(JZ_GPIO_PORTC(0), value, 0xffff);
159 static int n526_eink_init(struct broadsheetfb_par *par)
163 gpio_request(JZ_GPIO_PORTD(1), "display reset");
164 gpio_direction_output(JZ_GPIO_PORTD(1), 1);
166 gpio_set_value(JZ_GPIO_PORTD(1), 0);
168 gpio_request(JZ_GPIO_PORTB(18), "eink enable");
169 gpio_direction_output(JZ_GPIO_PORTB(18), 0);
171 gpio_request(JZ_GPIO_PORTB(29), "foobar");
172 gpio_direction_output(JZ_GPIO_PORTB(29), 1);
174 for(i = 1; i < ARRAY_SIZE(n526_eink_ctrl_gpios); ++i) {
175 gpio_request(n526_eink_ctrl_gpios[i], "eink display ctrl");
176 gpio_direction_output(n526_eink_ctrl_gpios[i], 0);
179 gpio_request(JZ_GPIO_PORTC(22), "foobar");
180 gpio_direction_input(JZ_GPIO_PORTC(22));
181 gpio_request(JZ_GPIO_PORTC(21), "eink nRD");
182 gpio_direction_output(JZ_GPIO_PORTC(21), 1);
184 for(i = 0; i < 16; ++i) {
185 gpio_request(JZ_GPIO_PORTC(i), "eink display data");
187 jz_gpio_port_direction_output(JZ_GPIO_PORTC(0), 0xffff);
189 gpio_set_value(JZ_GPIO_PORTB(18), 1);
194 static irqreturn_t n526_eink_busy_irq(int irq, void *devid)
196 struct broadsheetfb_par *par = devid;
197 wake_up(&par->waitq);
202 static int n526_eink_setup_irq(struct fb_info *info)
205 struct broadsheetfb_par *par = info->par;
207 gpio_request(JZ_GPIO_PORTB(17), "eink busy");
208 gpio_direction_input(JZ_GPIO_PORTB(17));
210 ret = request_irq(gpio_to_irq(JZ_GPIO_PORTB(17)), n526_eink_busy_irq,
211 IRQF_DISABLED | IRQF_TRIGGER_RISING,
212 "eink busyline", par);
214 printk("n526 display: Failed to request busyline irq: %d\n", ret);
218 static void n526_eink_cleanup(struct broadsheetfb_par *par)
222 static struct broadsheet_board broadsheet_pdata = {
223 .owner = THIS_MODULE,
224 .init = n526_eink_init,
225 .wait_for_rdy = n526_eink_wait,
226 .set_ctl = n526_eink_set_ctl,
227 .set_hdb = n526_eink_set_hdb,
228 .get_hdb = n526_eink_get_hdb,
229 .cleanup = n526_eink_cleanup,
230 .setup_irq = n526_eink_setup_irq,
233 static struct platform_device n526_broadsheet_device = {
234 .name = "broadsheetfb",
237 .platform_data = &broadsheet_pdata,
241 static struct gpio_keys_button qi_lb60_gpio_keys_buttons[] = {
250 static struct gpio_keys_platform_data qi_lb60_gpio_keys_data = {
251 .nbuttons = ARRAY_SIZE(qi_lb60_gpio_keys_buttons),
252 .buttons = qi_lb60_gpio_keys_buttons,
255 static struct platform_device qi_lb60_gpio_keys = {
259 .platform_data = &qi_lb60_gpio_keys_data,
263 static struct i2c_gpio_platform_data n526_i2c_pdata = {
264 .sda_pin = JZ_GPIO_PORTD(23),
265 .scl_pin = JZ_GPIO_PORTD(24),
270 static struct platform_device n526_i2c_device = {
274 .platform_data = &n526_i2c_pdata,
278 static struct i2c_board_info n526_i2c_board_info = {
283 static struct platform_device *jz_platform_devices[] __initdata = {
284 &jz4740_usb_ohci_device,
285 &jz4740_usb_gdt_device,
289 &jz4740_codec_device,
292 &n526_broadsheet_device,
298 static int __init n526_init_platform_devices(void)
301 jz4740_nand_device.dev.platform_data = &n526_nand_pdata;
302 jz4740_mmc_device.dev.platform_data = &n526_mmc_pdata;
304 n526_i2c_board_info.irq = gpio_to_irq(JZ_GPIO_PORTD(14)),
305 i2c_register_board_info(0, &n526_i2c_board_info, 1);
307 return platform_add_devices(jz_platform_devices,
308 ARRAY_SIZE(jz_platform_devices));
312 struct jz4740_clock_board_data jz4740_clock_bdata = {
313 .ext_rate = 12000000,
317 extern int jz_gpiolib_init(void);
319 static int __init n526_board_setup(void)
321 if (jz_gpiolib_init())
322 panic("Failed to initalize jz gpio\n");
324 jz4740_init_clocks();
327 if (n526_init_platform_devices())
328 panic("Failed to initalize platform devices\n");
333 arch_initcall(n526_board_setup);