juhosg [Tue, 17 Dec 2013 15:12:52 +0000 (15:12 +0000)]
ar71xx: ag71xx: use mdio bus name in ar7240_probe messages
The ar7240_probe function uses the network device name
in the kernel log messages, however the name is not yet
initialized when the ar7240_probe function is called.
Use the mdio bus name in the messages to avoid ugly
log lines like the following one:
eth%d: Found an AR7240/AR9330 built-in switch
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39116
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Tue, 17 Dec 2013 15:12:50 +0000 (15:12 +0000)]
ag71xx: ag71xx: use device name for debugfs entry
The ag71xx debugfs code uses the network device name
for the device specific debugfs directory. Since r38689
'ar71xx: ag71xx: fix a race involving netdev registration'
the debugfs initialization happens before the ethernet
device gets registered and the network device name contains
'eth%d' at this point. If the board setup code registers
multiple ag71xx devices, the debugfs code tries to create
the device specific dir with the same name which causes
an error like this:
eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=
004dd041, driver=Generic PHY]
ag71xx: probe of ag71xx.0 failed with error -12
Use the device name for the debugfs directory to avoid the
collisions. Also add an error message and change the return
code if the debugfs_create_dir call fails.
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39115
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Tue, 17 Dec 2013 07:17:00 +0000 (07:17 +0000)]
busybox: fix typo in Config.in (#14628)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39114
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 17 Dec 2013 02:47:20 +0000 (02:47 +0000)]
imx6: ventana: add canbus utils
Some of the Gateworks Ventana boards have CAN bus support, therefore
we will install the userspace utils.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39113
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 17 Dec 2013 02:47:18 +0000 (02:47 +0000)]
imx6: ventana: add default kernel modules for GSC
All Gateworks Ventana boards have a Gateworks System Controller
which emulates the following:
- ds1672 RTC
- pca953x GPIO expander
- hardware monitor
- at24 eeprom
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39112
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 17 Dec 2013 02:47:17 +0000 (02:47 +0000)]
imx6: add rtc feature support
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39111
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 17 Dec 2013 02:47:16 +0000 (02:47 +0000)]
kernel: add rtc-ds1672 module support
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39110
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 17 Dec 2013 02:47:15 +0000 (02:47 +0000)]
imx6: drop upstreamed patch
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39109
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Tue, 17 Dec 2013 02:47:13 +0000 (02:47 +0000)]
[tools] automake: update to 1.11.6
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39108
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Mon, 16 Dec 2013 19:27:35 +0000 (19:27 +0000)]
busybox: add support for config overrides via env/busybox-config
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39107
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Mon, 16 Dec 2013 19:09:57 +0000 (19:09 +0000)]
busybox: remove busybox menuconfig from top level menuconfig
This will help with avoiding bogus bug reports caused by stale configs
and bad cases of user tinkering :)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39106
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Mon, 16 Dec 2013 18:49:10 +0000 (18:49 +0000)]
uClibc: disable sha256 and sha512 for libcrypt - saves about 13k uncompressed in libcrypt
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39105
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Mon, 16 Dec 2013 18:42:43 +0000 (18:42 +0000)]
hostapd: move old wifi setup scripts to hostapd-common-old
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39103
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Mon, 16 Dec 2013 18:08:51 +0000 (18:08 +0000)]
ar71xx: add initial support for the Mikrotik RB911G/RB912UAG boards
It is only on RB911G-5HPnD and RB912UAG-5HPnD boards.
The LEDs and the USB port is not working yet.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39102
3c298f89-4303-0410-b956-
a3cf2f4a3e73
jow [Mon, 16 Dec 2013 16:47:41 +0000 (16:47 +0000)]
dnsmasq: switch to /lib/functions/network.sh
This commit changes the dnsmasq init script to use the interface
status exposed by netifd. The old references to scan_interfaces()
and (indirect) accesses to uci state variables are removed and
replaced with corresponding network_*() calls.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39101
3c298f89-4303-0410-b956-
a3cf2f4a3e73
jow [Mon, 16 Dec 2013 16:29:23 +0000 (16:29 +0000)]
base-files: ipcalc.sh: support bit length as netmask parameter
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39100
3c298f89-4303-0410-b956-
a3cf2f4a3e73
jow [Mon, 16 Dec 2013 16:28:45 +0000 (16:28 +0000)]
base-files: add network_get_protocol() to /lib/functions/network.sh
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39099
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Mon, 16 Dec 2013 15:45:57 +0000 (15:45 +0000)]
mac80211: fix AP mode scanning issues
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39098
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Mon, 16 Dec 2013 12:57:24 +0000 (12:57 +0000)]
ar71xx: add NAND driver for the Mikrotik RB91x boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39097
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Mon, 16 Dec 2013 12:41:48 +0000 (12:41 +0000)]
ar71xx: rb2011: use board name from the hardware config
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39096
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Mon, 16 Dec 2013 10:28:42 +0000 (10:28 +0000)]
ar71xx: rb2011: simplify setup code
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39095
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Mon, 16 Dec 2013 10:28:41 +0000 (10:28 +0000)]
ar71xx: rb2011: use the new RouterBOOT helpers
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39094
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 16 Dec 2013 10:16:33 +0000 (10:16 +0000)]
ralink: fix dir810 networking
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39093
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Mon, 16 Dec 2013 10:11:02 +0000 (10:11 +0000)]
ar71xx: rb95x: use the rb_get_wlan_data helper
Also remove unused RB_* defines.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39092
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Mon, 16 Dec 2013 10:11:01 +0000 (10:11 +0000)]
ar71xx: add some RouterBOOT specific helper functions
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39091
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Mon, 16 Dec 2013 10:11:00 +0000 (10:11 +0000)]
kernel: define RB_ID_HW_OPTIONS in include/linux/routerboot.h
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39090
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Mon, 16 Dec 2013 10:10:58 +0000 (10:10 +0000)]
ar71xx: refresh m25p80 patches
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39089
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Mon, 16 Dec 2013 10:08:13 +0000 (10:08 +0000)]
netifd: update to latest version, fixes a null pointer crash
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39088
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Mon, 16 Dec 2013 08:17:40 +0000 (08:17 +0000)]
ar71xx: rb95x: nuke rb95x_gpio_init
Set up the chipselect GPIO directly in rb95x_nand_init
instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39087
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Mon, 16 Dec 2013 08:16:09 +0000 (08:16 +0000)]
kernel/3.1[02]: add Winbond W25X05 SPI flash support
It is used on newer RouterBOARDs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39086
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Mon, 16 Dec 2013 07:51:21 +0000 (07:51 +0000)]
kernel: remove obsolete yaffs options from target configs
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39085
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Mon, 16 Dec 2013 07:51:19 +0000 (07:51 +0000)]
kernel: update yaffs code
Use the latest version of the yaffs code. Fetched from the
yaffs2 git tree and it is based on the following commit:
commit
bc76682d93955cfb33051beb503ad9f8a5450578
Merge:
3a8580e ffa781d
Author: Charles Manning <cdhmanning@gmail.com>
Date: Thu Jul 11 17:46:25 2013 +1200
Merge branch 'master' of ssh://www.aleph1.co.uk/home/aleph1/git/yaffs2
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39084
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Mon, 16 Dec 2013 07:42:43 +0000 (07:42 +0000)]
kernel/3.9: remove yaffs patches
It is not used by any platform.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39083
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Mon, 16 Dec 2013 07:42:42 +0000 (07:42 +0000)]
kernel/3.6: remove yaffs support
It is not used by any platform.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39082
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Mon, 16 Dec 2013 07:42:41 +0000 (07:42 +0000)]
kernel/3.3: remove yaffs support
It is not used by any platform.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39081
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Mon, 16 Dec 2013 07:39:22 +0000 (07:39 +0000)]
ar71xx/mikrotik: disable unused MTD options
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39080
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Mon, 16 Dec 2013 07:37:31 +0000 (07:37 +0000)]
ar71xx: add dummy rle_decode function if CONFIG_RLE_DECOMPRESS is not set
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39079
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Mon, 16 Dec 2013 07:16:43 +0000 (07:16 +0000)]
ar71xx: add userspace support for WD My Net N750
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
[juhosg: remove the image generation part until the ethernet
switch issue is resolved]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39078
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Mon, 16 Dec 2013 07:16:42 +0000 (07:16 +0000)]
ar71xx: add kernel support for WD My Net N750
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
[juhosg: use a separate patch for kernel changes]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39077
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Sun, 15 Dec 2013 22:18:04 +0000 (22:18 +0000)]
generic: ar8216: Enable jumbo frames on AR8327 by default
This patch enables jumbo frames on AR8327 switch by default.
I have tested it on TP-Link TL-WDR3600.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39076
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Sun, 15 Dec 2013 21:34:20 +0000 (21:34 +0000)]
ar71xx: build image for the TP-Link TL-WA901ND v3 board
Based-on: http://patchwork.openwrt.org/patch/4507/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39075
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Sun, 15 Dec 2013 21:34:19 +0000 (21:34 +0000)]
ar71xx: add user-space support for the TP-Link TL-WA901ND v3 board
Based-on: http://patchwork.openwrt.org/patch/4508/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39074
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Sun, 15 Dec 2013 21:34:18 +0000 (21:34 +0000)]
ar71xx: add kernel support for the TL-WA901ND v3 board
Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39073
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Sun, 15 Dec 2013 21:34:17 +0000 (21:34 +0000)]
ar71xx: move TL-WA801ND v2 setup code
The TL-WA801ND v2 board has only one LAN port which makes
it more similar to the TL-WR[78]50RE devices. Move the
board setup code into the mach-tl-wax50re.c file.
Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39072
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Sun, 15 Dec 2013 21:34:15 +0000 (21:34 +0000)]
ar71xx: refactor TL-WAx50RE setup code
This way it is a bit easier to add other TP-LINK devices based on the
Atheros AP123 reference board with one LAN port.
Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39071
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Sun, 15 Dec 2013 21:07:34 +0000 (21:07 +0000)]
[tools] ppl: update to 1.1
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39068
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Sun, 15 Dec 2013 21:07:32 +0000 (21:07 +0000)]
[tools] cloog: update to 0.18.1
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39067
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Sun, 15 Dec 2013 20:39:13 +0000 (20:39 +0000)]
firmware-utils/mkplinkfw: add TL-WA801ND v2 support
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4503/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39066
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Sun, 15 Dec 2013 20:39:12 +0000 (20:39 +0000)]
ar71xx: build firmware image for the TL-WA801ND v2
Patch to add the profile for the TP-LINK WA801ND v2
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4502/
[juhosg: change subject]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39065
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Sun, 15 Dec 2013 20:39:11 +0000 (20:39 +0000)]
ar71xx: add user space support for the TL-WA801ND v2
Patch to add the user space support for the TL-WA801ND v2
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4501/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39064
3c298f89-4303-0410-b956-
a3cf2f4a3e73
juhosg [Sun, 15 Dec 2013 20:39:10 +0000 (20:39 +0000)]
ar71xx: add kernel support for the TL-WA801ND v2 board
Patch to add kernel support for the TP-LINK WA801ND v2
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4500/
[juhosg:
- the TL-WA801ND v2 does not have a sliding switch, it uses a push button
for WPS instead. Use the tl_mr3420v2_gpio_keys array to reflect that,
- rename kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39063
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Sun, 15 Dec 2013 20:23:00 +0000 (20:23 +0000)]
ath9k: fix interrupt storms on AR913x
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39062
3c298f89-4303-0410-b956-
a3cf2f4a3e73
cyrus [Sun, 15 Dec 2013 19:38:53 +0000 (19:38 +0000)]
Convert DHCP->6rd and DHCPv6->DS-Lite autoconfig to dynamic interface
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39061
3c298f89-4303-0410-b956-
a3cf2f4a3e73
hauke [Sun, 15 Dec 2013 19:19:16 +0000 (19:19 +0000)]
brcm47xx: deactivate early printk support
This breaks some devices where the serial console is not at port 0 but
somewhere else.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39060
3c298f89-4303-0410-b956-
a3cf2f4a3e73
hauke [Sun, 15 Dec 2013 19:16:30 +0000 (19:16 +0000)]
kernel: update kernel 3.10 to 3.10.24
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39059
3c298f89-4303-0410-b956-
a3cf2f4a3e73
cyrus [Sun, 15 Dec 2013 19:10:20 +0000 (19:10 +0000)]
odhcp6c: add source routing support
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39058
3c298f89-4303-0410-b956-
a3cf2f4a3e73
jow [Sun, 15 Dec 2013 15:32:37 +0000 (15:32 +0000)]
uhttpd: don't process ubus_* and lua_* options if corresponding plugin is not installed (#14618)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39057
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Sun, 15 Dec 2013 03:59:49 +0000 (03:59 +0000)]
[tools] bison: update to 3.0.2
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39056
3c298f89-4303-0410-b956-
a3cf2f4a3e73
kaloz [Sat, 14 Dec 2013 17:37:14 +0000 (17:37 +0000)]
upgrade 3.12 targets to 3.12.5
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39055
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Sat, 14 Dec 2013 17:07:08 +0000 (17:07 +0000)]
ath9k: merge another round of cleanups and fixes submitted to linux-wireless
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39054
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Sat, 14 Dec 2013 16:40:27 +0000 (16:40 +0000)]
ath9k: merge an interrupt processing fix for AR5008-AR9002
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39053
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Sat, 14 Dec 2013 16:40:24 +0000 (16:40 +0000)]
kernel: move BLKCIPHER into crypto-core to avoid pulling in crypto-manager for arc4 (used by mac80211)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39052
3c298f89-4303-0410-b956-
a3cf2f4a3e73
kaloz [Sat, 14 Dec 2013 16:29:35 +0000 (16:29 +0000)]
[omap]: drop the bootscript, new u-boots won't need it
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39051
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Sat, 14 Dec 2013 14:59:05 +0000 (14:59 +0000)]
netifd: update to the latest version, adds a revert of the link state handling patches which caused regressions in combination with wifi devices
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39050
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Sat, 14 Dec 2013 13:14:44 +0000 (13:14 +0000)]
build: speed up kernel symbol export stripping
GNU grep has a high per-expression setup overhead when compiling regular
expressions. Use -F to force it to interpret the input as fixed strings,
which is much faster (fraction of a second instead of multiple minutes).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39049
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Sat, 14 Dec 2013 10:19:48 +0000 (10:19 +0000)]
openssl: Support multi-threaded applications
Allow multi-threaded applications to work properly by
removing the "no-threads" flag that is enabled by default.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39048
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Fri, 13 Dec 2013 16:43:15 +0000 (16:43 +0000)]
usbmode: add an init script to switch devices that show up too early for the hotplug script
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39047
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Fri, 13 Dec 2013 16:43:11 +0000 (16:43 +0000)]
netifd: prevent an unnecessary restart of netifd-managed wifi interfaces at boot time
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39046
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Fri, 13 Dec 2013 16:43:07 +0000 (16:43 +0000)]
scripts/download.pl: prefer the GNU mirror redirect over the primary site (#14603)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39045
3c298f89-4303-0410-b956-
a3cf2f4a3e73
kaloz [Fri, 13 Dec 2013 16:38:43 +0000 (16:38 +0000)]
[uboot-omap]: fix jffs2 with internal libgcc and switch omap4 to ext4
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39044
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Fri, 13 Dec 2013 11:02:05 +0000 (11:02 +0000)]
iw: reduce size and make the phy dump output more readable
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39041
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Fri, 13 Dec 2013 10:53:34 +0000 (10:53 +0000)]
ralink: add mt7621 support
there are still various missing pieces for full support.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39040
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Fri, 13 Dec 2013 10:40:26 +0000 (10:40 +0000)]
opkg: do not add blank "Provides:" fields to package metadata
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39039
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Fri, 13 Dec 2013 10:40:19 +0000 (10:40 +0000)]
build: remove SourceFile and SourceURL from opkg metadata - they are useless without the corresponding openwrt package directory
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39038
3c298f89-4303-0410-b956-
a3cf2f4a3e73
kaloz [Thu, 12 Dec 2013 10:08:15 +0000 (10:08 +0000)]
[omap]: add a default profile file
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39037
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Wed, 11 Dec 2013 19:48:19 +0000 (19:48 +0000)]
/sbin/wifi: reload network/wireless on wifi restart
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39036
3c298f89-4303-0410-b956-
a3cf2f4a3e73
nbd [Wed, 11 Dec 2013 18:23:52 +0000 (18:23 +0000)]
netifd: fix crashes triggered by adding/removing wireless devices on reload
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39035
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Wed, 11 Dec 2013 10:56:11 +0000 (10:56 +0000)]
imx6: add canbus support for Ventana boards
GW5400, GW5300, and GW5200 have CAN bus option.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39034
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Wed, 11 Dec 2013 10:56:09 +0000 (10:56 +0000)]
imx6: add flexcan support
backport upstream changes to 3.10:
- 0060-flexcan.patch:
- add flexcan pinctrl and devicetree config
- 0061-can-flexcan-use-correct-clock-as-base-for-bit-rate-c.patch
- fix a clock issue
- 0062-ARM-i.MX6q-fix-the-wrong-parent-of-can_root-clock.patch
- fix a clock issue
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39033
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Wed, 11 Dec 2013 10:56:08 +0000 (10:56 +0000)]
kernel: add CAN modules
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39032
3c298f89-4303-0410-b956-
a3cf2f4a3e73
jow [Tue, 10 Dec 2013 16:24:52 +0000 (16:24 +0000)]
mac80211: add missing set_default to fix stray "radio0: sh: bad number" messages
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39028
3c298f89-4303-0410-b956-
a3cf2f4a3e73
jow [Tue, 10 Dec 2013 16:24:48 +0000 (16:24 +0000)]
hostapd: fix short_preamble option
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39027
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 9 Dec 2013 18:26:58 +0000 (18:26 +0000)]
libevent2: Configure with --disable-debug-mode
Saves around 10K.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39025
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 9 Dec 2013 18:24:30 +0000 (18:24 +0000)]
ubox: fix logging support. the initial connect failed
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39024
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 9 Dec 2013 17:38:19 +0000 (17:38 +0000)]
procd: update procd, add ulimit support
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39023
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 9 Dec 2013 17:29:44 +0000 (17:29 +0000)]
ubox: fix up pidcount handling inside log.init
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39022
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 9 Dec 2013 17:29:39 +0000 (17:29 +0000)]
gpio-button-hotplug: add irq mode to driver
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39021
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 9 Dec 2013 17:29:34 +0000 (17:29 +0000)]
netifd: enable coredumps again
got broken due procd startup. Requires procd resource limit patch.
Signed-off-by: Ulrich Weber <uw@xyne.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39020
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 9 Dec 2013 17:29:29 +0000 (17:29 +0000)]
ralink: add TSO
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39019
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 9 Dec 2013 17:29:24 +0000 (17:29 +0000)]
ralink: fix typo in gpio irq handling
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39018
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 9 Dec 2013 17:29:19 +0000 (17:29 +0000)]
ralink: add mt7620a gdma info to dtsi
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39017
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 9 Dec 2013 17:29:14 +0000 (17:29 +0000)]
ralink: add asoc modules
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39016
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 9 Dec 2013 17:29:08 +0000 (17:29 +0000)]
ralink: add partially working asoc driver. codec is not fully functional yet
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39015
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 9 Dec 2013 17:29:03 +0000 (17:29 +0000)]
ralink: add helper that identifies the mt7620 ECO
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39014
3c298f89-4303-0410-b956-
a3cf2f4a3e73
blogic [Mon, 9 Dec 2013 17:28:43 +0000 (17:28 +0000)]
ralink: add dma engine support
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39013
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Mon, 9 Dec 2013 11:30:23 +0000 (11:30 +0000)]
imx6: add support for GW53xx
The Gateworks GW53xx family of products is based on the Freescale
i.MX6DL SoC and offers a small form-factor with peripherals such as:
* i.MX6DL
* NAND FLASH
* 4x PCIe
* 4x USB EHCI (1x front-panel; 3x PCIe sockets)
* 1x USB OTG
* 1x uSD
* LVDS connector (VLDS for display, PWM/GPIO for backlight, i2c for touch)
* HDMI Audio/Video out
* Analog Video in
* Digital IO
* Gateworks System Controller
* Accelerometer
* Canbus
* Optional GPS
* Industrial temp (-40C to +85C)
* DC input voltage 8 to 42V (Passive PoE and 802.3af)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39012
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Mon, 9 Dec 2013 11:30:22 +0000 (11:30 +0000)]
imx6: add DMA/SDMA support for 3.12
DMA and SDMA support are needed for ssi based audio. Note that the sdma
firmware is no longer required for ssi audio.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39011
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Mon, 9 Dec 2013 11:30:20 +0000 (11:30 +0000)]
imx6: drop upstreamed patch
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39010
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Mon, 9 Dec 2013 11:30:19 +0000 (11:30 +0000)]
kernel: added defines for 3.12
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39009
3c298f89-4303-0410-b956-
a3cf2f4a3e73
luka [Mon, 9 Dec 2013 11:30:18 +0000 (11:30 +0000)]
kernel: module updates for 3.12
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39008
3c298f89-4303-0410-b956-
a3cf2f4a3e73
projects / openwrt.git / log