--- a/nl80211.h
+++ b/nl80211.h
-@@ -118,8 +118,9 @@
- * to get a list of all present wiphys.
- * @NL80211_CMD_SET_WIPHY: set wiphy parameters, needs %NL80211_ATTR_WIPHY or
- * %NL80211_ATTR_IFINDEX; can be used to set %NL80211_ATTR_WIPHY_NAME,
-- * %NL80211_ATTR_WIPHY_TXQ_PARAMS, %NL80211_ATTR_WIPHY_FREQ,
-- * %NL80211_ATTR_WIPHY_CHANNEL_TYPE, %NL80211_ATTR_WIPHY_RETRY_SHORT,
-+ * %NL80211_ATTR_WIPHY_TXQ_PARAMS, %NL80211_ATTR_WIPHY_FREQ (and the
-+ * attributes determining the channel width; this is used for setting
-+ * monitor mode channel), %NL80211_ATTR_WIPHY_RETRY_SHORT,
- * %NL80211_ATTR_WIPHY_RETRY_LONG, %NL80211_ATTR_WIPHY_FRAG_THRESHOLD,
- * and/or %NL80211_ATTR_WIPHY_RTS_THRESHOLD.
- * However, for setting the channel, see %NL80211_CMD_SET_CHANNEL
-@@ -171,7 +172,7 @@
- * %NL80211_ATTR_AKM_SUITES, %NL80211_ATTR_PRIVACY,
- * %NL80211_ATTR_AUTH_TYPE and %NL80211_ATTR_INACTIVITY_TIMEOUT.
- * The channel to use can be set on the interface or be given using the
-- * %NL80211_ATTR_WIPHY_FREQ and %NL80211_ATTR_WIPHY_CHANNEL_TYPE attrs.
-+ * %NL80211_ATTR_WIPHY_FREQ and the attributes determining channel width.
- * @NL80211_CMD_NEW_BEACON: old alias for %NL80211_CMD_START_AP
- * @NL80211_CMD_STOP_AP: Stop AP operation on the given interface
- * @NL80211_CMD_DEL_BEACON: old alias for %NL80211_CMD_STOP_AP
-@@ -401,8 +402,7 @@
- * a response while being associated to an AP on another channel.
- * %NL80211_ATTR_IFINDEX is used to specify which interface (and thus
- * radio) is used. %NL80211_ATTR_WIPHY_FREQ is used to specify the
-- * frequency for the operation and %NL80211_ATTR_WIPHY_CHANNEL_TYPE may be
-- * optionally used to specify additional channel parameters.
-+ * frequency for the operation.
- * %NL80211_ATTR_DURATION is used to specify the duration in milliseconds
- * to remain on the channel. This command is also used as an event to
- * notify when the requested duration starts (it may take a while for the
-@@ -440,12 +440,11 @@
- * as an event indicating reception of a frame that was not processed in
- * kernel code, but is for us (i.e., which may need to be processed in a
- * user space application). %NL80211_ATTR_FRAME is used to specify the
-- * frame contents (including header). %NL80211_ATTR_WIPHY_FREQ (and
-- * optionally %NL80211_ATTR_WIPHY_CHANNEL_TYPE) is used to indicate on
-- * which channel the frame is to be transmitted or was received. If this
-- * channel is not the current channel (remain-on-channel or the
-- * operational channel) the device will switch to the given channel and
-- * transmit the frame, optionally waiting for a response for the time
-+ * frame contents (including header). %NL80211_ATTR_WIPHY_FREQ is used
-+ * to indicate on which channel the frame is to be transmitted or was
-+ * received. If this channel is not the current channel (remain-on-channel
-+ * or the operational channel) the device will switch to the given channel
-+ * and transmit the frame, optionally waiting for a response for the time
- * specified using %NL80211_ATTR_DURATION. When called, this operation
- * returns a cookie (%NL80211_ATTR_COOKIE) that will be included with the
- * TX status event pertaining to the TX request.
-@@ -473,8 +472,8 @@
- * command is used as an event to indicate the that a trigger level was
- * reached.
- * @NL80211_CMD_SET_CHANNEL: Set the channel (using %NL80211_ATTR_WIPHY_FREQ
-- * and %NL80211_ATTR_WIPHY_CHANNEL_TYPE) the given interface (identifed
-- * by %NL80211_ATTR_IFINDEX) shall operate on.
-+ * and the attributes determining channel width) the given interface
-+ * (identifed by %NL80211_ATTR_IFINDEX) shall operate on.
- * In case multiple channels are supported by the device, the mechanism
- * with which it switches channels is implementation-defined.
- * When a monitor interface is given, it can only switch channel while
-@@ -526,6 +525,12 @@
- * of PMKSA caching dandidates.
+@@ -1761,6 +1761,9 @@ enum nl80211_commands {
+ * @NL80211_ATTR_REG_INDOOR: flag attribute, if set indicates that the device
+ * is operating in an indoor environment.
*
- * @NL80211_CMD_TDLS_OPER: Perform a high-level TDLS command (e.g. link setup).
-+ * In addition, this can be used as an event to request userspace to take
-+ * actions on TDLS links (set up a new link or tear down an existing one).
-+ * In such events, %NL80211_ATTR_TDLS_OPERATION indicates the requested
-+ * operation, %NL80211_ATTR_MAC contains the peer MAC address, and
-+ * %NL80211_ATTR_REASON_CODE the reason code to be used (only with
-+ * %NL80211_TDLS_TEARDOWN).
- * @NL80211_CMD_TDLS_MGMT: Send a TDLS management frame.
- *
- * @NL80211_CMD_UNEXPECTED_FRAME: Used by an application controlling an AP
-@@ -562,8 +567,24 @@
- *
- * @NL80211_CMD_CH_SWITCH_NOTIFY: An AP or GO may decide to switch channels
- * independently of the userspace SME, send this event indicating
-- * %NL80211_ATTR_IFINDEX is now on %NL80211_ATTR_WIPHY_FREQ with
-- * %NL80211_ATTR_WIPHY_CHANNEL_TYPE.
-+ * %NL80211_ATTR_IFINDEX is now on %NL80211_ATTR_WIPHY_FREQ and the
-+ * attributes determining channel width.
-+ *
-+ * @NL80211_CMD_START_P2P_DEVICE: Start the given P2P Device, identified by
-+ * its %NL80211_ATTR_WDEV identifier. It must have been created with
-+ * %NL80211_CMD_NEW_INTERFACE previously. After it has been started, the
-+ * P2P Device can be used for P2P operations, e.g. remain-on-channel and
-+ * public action frame TX.
-+ * @NL80211_CMD_STOP_P2P_DEVICE: Stop the given P2P Device, identified by
-+ * its %NL80211_ATTR_WDEV identifier.
-+ *
-+ * @NL80211_CMD_CONN_FAILED: connection request to an AP failed; used to
-+ * notify userspace that AP has rejected the connection request from a
-+ * station, due to particular reason. %NL80211_ATTR_CONN_FAILED_REASON
-+ * is used for this.
-+ *
-+ * @NL80211_CMD_SET_MCAST_RATE: Change the rate used to send multicast frames
-+ * for IBSS or MESH vif.
- *
- * @NL80211_CMD_MAX: highest used command number
- * @__NL80211_CMD_AFTER_LAST: internal use
-@@ -708,6 +729,13 @@ enum nl80211_commands {
-
- NL80211_CMD_CH_SWITCH_NOTIFY,
-
-+ NL80211_CMD_START_P2P_DEVICE,
-+ NL80211_CMD_STOP_P2P_DEVICE,
-+
-+ NL80211_CMD_CONN_FAILED,
-+
-+ NL80211_CMD_SET_MCAST_RATE,
-+
- /* add new commands above here */
-
- /* used to define NL80211_CMD_MAX below */
-@@ -744,14 +772,26 @@ enum nl80211_commands {
- * /sys/class/ieee80211/<phyname>/index
- * @NL80211_ATTR_WIPHY_NAME: wiphy name (used for renaming)
- * @NL80211_ATTR_WIPHY_TXQ_PARAMS: a nested array of TX queue parameters
-- * @NL80211_ATTR_WIPHY_FREQ: frequency of the selected channel in MHz
-+ * @NL80211_ATTR_WIPHY_FREQ: frequency of the selected channel in MHz,
-+ * defines the channel together with the (deprecated)
-+ * %NL80211_ATTR_WIPHY_CHANNEL_TYPE attribute or the attributes
-+ * %NL80211_ATTR_CHANNEL_WIDTH and if needed %NL80211_ATTR_CENTER_FREQ1
-+ * and %NL80211_ATTR_CENTER_FREQ2
-+ * @NL80211_ATTR_CHANNEL_WIDTH: u32 attribute containing one of the values
-+ * of &enum nl80211_chan_width, describing the channel width. See the
-+ * documentation of the enum for more information.
-+ * @NL80211_ATTR_CENTER_FREQ1: Center frequency of the first part of the
-+ * channel, used for anything but 20 MHz bandwidth
-+ * @NL80211_ATTR_CENTER_FREQ2: Center frequency of the second part of the
-+ * channel, used only for 80+80 MHz bandwidth
- * @NL80211_ATTR_WIPHY_CHANNEL_TYPE: included with NL80211_ATTR_WIPHY_FREQ
-- * if HT20 or HT40 are allowed (i.e., 802.11n disabled if not included):
-+ * if HT20 or HT40 are to be used (i.e., HT disabled if not included):
- * NL80211_CHAN_NO_HT = HT not allowed (i.e., same as not including
- * this attribute)
- * NL80211_CHAN_HT20 = HT20 only
- * NL80211_CHAN_HT40MINUS = secondary channel is below the primary channel
- * NL80211_CHAN_HT40PLUS = secondary channel is above the primary channel
-+ * This attribute is now deprecated.
- * @NL80211_ATTR_WIPHY_RETRY_SHORT: TX retry limit for frames whose length is
- * less than or equal to the RTS threshold; allowed range: 1..255;
- * dot11ShortRetryLimit; u8
-@@ -1251,6 +1291,25 @@ enum nl80211_commands {
- * was used to provide the hint. For the different types of
- * allowed user regulatory hints see nl80211_user_reg_hint_type.
- *
-+ * @NL80211_ATTR_CONN_FAILED_REASON: The reason for which AP has rejected
-+ * the connection request from a station. nl80211_connect_failed_reason
-+ * enum has different reasons of connection failure.
-+ *
-+ * @NL80211_ATTR_SAE_DATA: SAE elements in Authentication frames. This starts
-+ * with the Authentication transaction sequence number field.
-+ *
-+ * @NL80211_ATTR_VHT_CAPABILITY: VHT Capability information element (from
-+ * association request when used with NL80211_CMD_NEW_STATION)
-+ *
-+ * @NL80211_ATTR_SCAN_FLAGS: scan request control flags (u32)
-+ *
-+ * @NL80211_ATTR_P2P_CTWINDOW: P2P GO Client Traffic Window (u8), used with
-+ * the START_AP and SET_BSS commands
-+ * @NL80211_ATTR_P2P_OPPPS: P2P GO opportunistic PS (u8), used with the
-+ * START_AP and SET_BSS commands. This can have the values 0 or 1;
-+ * if not given in START_AP 0 is assumed, if not given in SET_BSS
-+ * no change is made.
++ * @NL80211_ATTR_WIPHY_ANTENNA_GAIN: Configured antenna gain. Used to reduce
++ * transmit power to stay within regulatory limits. u32, dBi.
+ *
+ * @NUM_NL80211_ATTR: total number of nl80211_attrs available
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
- */
-@@ -1506,6 +1565,23 @@ enum nl80211_attrs {
+@@ -2130,6 +2133,8 @@ enum nl80211_attrs {
- NL80211_ATTR_USER_REG_HINT_TYPE,
+ NL80211_ATTR_REG_INDOOR,
-+ NL80211_ATTR_CONN_FAILED_REASON,
-+
-+ NL80211_ATTR_SAE_DATA,
-+
-+ NL80211_ATTR_VHT_CAPABILITY,
-+
-+ NL80211_ATTR_SCAN_FLAGS,
-+
-+ NL80211_ATTR_CHANNEL_WIDTH,
-+ NL80211_ATTR_CENTER_FREQ1,
-+ NL80211_ATTR_CENTER_FREQ2,
-+
-+ NL80211_ATTR_P2P_CTWINDOW,
-+ NL80211_ATTR_P2P_OPPPS,
-+
+ NL80211_ATTR_WIPHY_ANTENNA_GAIN,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
-@@ -1549,6 +1625,7 @@ enum nl80211_attrs {
- #define NL80211_TKIP_DATA_OFFSET_TX_MIC_KEY 16
- #define NL80211_TKIP_DATA_OFFSET_RX_MIC_KEY 24
- #define NL80211_HT_CAPABILITY_LEN 26
-+#define NL80211_VHT_CAPABILITY_LEN 12
-
- #define NL80211_MAX_NR_CIPHER_SUITES 5
- #define NL80211_MAX_NR_AKM_SUITES 2
-@@ -1575,6 +1652,10 @@ enum nl80211_attrs {
- * @NL80211_IFTYPE_MESH_POINT: mesh point
- * @NL80211_IFTYPE_P2P_CLIENT: P2P client
- * @NL80211_IFTYPE_P2P_GO: P2P group owner
-+ * @NL80211_IFTYPE_P2P_DEVICE: P2P device interface type, this is not a netdev
-+ * and therefore can't be created in the normal ways, use the
-+ * %NL80211_CMD_START_P2P_DEVICE and %NL80211_CMD_STOP_P2P_DEVICE
-+ * commands to create and destroy one
- * @NL80211_IFTYPE_MAX: highest interface type number currently defined
- * @NUM_NL80211_IFTYPES: number of defined interface types
- *
-@@ -1593,6 +1674,7 @@ enum nl80211_iftype {
- NL80211_IFTYPE_MESH_POINT,
- NL80211_IFTYPE_P2P_CLIENT,
- NL80211_IFTYPE_P2P_GO,
-+ NL80211_IFTYPE_P2P_DEVICE,
-
- /* keep last */
- NUM_NL80211_IFTYPES,
-@@ -1664,10 +1746,15 @@ struct nl80211_sta_flag_update {
- * @__NL80211_RATE_INFO_INVALID: attribute number 0 is reserved
- * @NL80211_RATE_INFO_BITRATE: total bitrate (u16, 100kbit/s)
- * @NL80211_RATE_INFO_MCS: mcs index for 802.11n (u8)
-- * @NL80211_RATE_INFO_40_MHZ_WIDTH: 40 Mhz dualchannel bitrate
-+ * @NL80211_RATE_INFO_40_MHZ_WIDTH: 40 MHz dualchannel bitrate
- * @NL80211_RATE_INFO_SHORT_GI: 400ns guard interval
- * @NL80211_RATE_INFO_BITRATE32: total bitrate (u32, 100kbit/s)
- * @NL80211_RATE_INFO_MAX: highest rate_info number currently defined
-+ * @NL80211_RATE_INFO_VHT_MCS: MCS index for VHT (u8)
-+ * @NL80211_RATE_INFO_VHT_NSS: number of streams in VHT (u8)
-+ * @NL80211_RATE_INFO_80_MHZ_WIDTH: 80 MHz VHT rate
-+ * @NL80211_RATE_INFO_80P80_MHZ_WIDTH: 80+80 MHz VHT rate
-+ * @NL80211_RATE_INFO_160_MHZ_WIDTH: 160 MHz VHT rate
- * @__NL80211_RATE_INFO_AFTER_LAST: internal use
+@@ -2620,16 +2625,17 @@ enum nl80211_band_attr {
+ * an indoor surroundings, i.e., it is connected to AC power (and not
+ * through portable DC inverters) or is under the control of a master
+ * that is acting as an AP and is connected to AC power.
+- * @NL80211_FREQUENCY_ATTR_GO_CONCURRENT: GO operation is allowed on this
++ * @NL80211_FREQUENCY_ATTR_IR_CONCURRENT: IR operation is allowed on this
+ * channel if it's connected concurrently to a BSS on the same channel on
+ * the 2 GHz band or to a channel in the same UNII band (on the 5 GHz
+- * band), and IEEE80211_CHAN_RADAR is not set. Instantiating a GO on a
+- * channel that has the GO_CONCURRENT attribute set can be done when there
+- * is a clear assessment that the device is operating under the guidance of
+- * an authorized master, i.e., setting up a GO while the device is also
+- * connected to an AP with DFS and radar detection on the UNII band (it is
+- * up to user-space, i.e., wpa_supplicant to perform the required
+- * verifications)
++ * band), and IEEE80211_CHAN_RADAR is not set. Instantiating a GO or TDLS
++ * off-channel on a channel that has the IR_CONCURRENT attribute set can be
++ * done when there is a clear assessment that the device is operating under
++ * the guidance of an authorized master, i.e., setting up a GO or TDLS
++ * off-channel while the device is also connected to an AP with DFS and
++ * radar detection on the UNII band (it is up to user-space, i.e.,
++ * wpa_supplicant to perform the required verifications). Using this
++ * attribute for IR is disallowed for master interfaces (IBSS, AP).
+ * @NL80211_FREQUENCY_ATTR_NO_20MHZ: 20 MHz operation is not allowed
+ * on this channel in current regulatory domain.
+ * @NL80211_FREQUENCY_ATTR_NO_10MHZ: 10 MHz operation is not allowed
+@@ -2641,7 +2647,7 @@ enum nl80211_band_attr {
+ * See https://apps.fcc.gov/eas/comments/GetPublishedDocument.html?id=327&tn=528122
+ * for more information on the FCC description of the relaxations allowed
+ * by NL80211_FREQUENCY_ATTR_INDOOR_ONLY and
+- * NL80211_FREQUENCY_ATTR_GO_CONCURRENT.
++ * NL80211_FREQUENCY_ATTR_IR_CONCURRENT.
*/
- enum nl80211_rate_info {
-@@ -1677,6 +1764,11 @@ enum nl80211_rate_info {
- NL80211_RATE_INFO_40_MHZ_WIDTH,
- NL80211_RATE_INFO_SHORT_GI,
- NL80211_RATE_INFO_BITRATE32,
-+ NL80211_RATE_INFO_VHT_MCS,
-+ NL80211_RATE_INFO_VHT_NSS,
-+ NL80211_RATE_INFO_80_MHZ_WIDTH,
-+ NL80211_RATE_INFO_80P80_MHZ_WIDTH,
-+ NL80211_RATE_INFO_160_MHZ_WIDTH,
+ enum nl80211_frequency_attr {
+ __NL80211_FREQUENCY_ATTR_INVALID,
+@@ -2659,7 +2665,7 @@ enum nl80211_frequency_attr {
+ NL80211_FREQUENCY_ATTR_NO_160MHZ,
+ NL80211_FREQUENCY_ATTR_DFS_CAC_TIME,
+ NL80211_FREQUENCY_ATTR_INDOOR_ONLY,
+- NL80211_FREQUENCY_ATTR_GO_CONCURRENT,
++ NL80211_FREQUENCY_ATTR_IR_CONCURRENT,
+ NL80211_FREQUENCY_ATTR_NO_20MHZ,
+ NL80211_FREQUENCY_ATTR_NO_10MHZ,
- /* keep last */
- __NL80211_RATE_INFO_AFTER_LAST,
-@@ -1744,6 +1836,8 @@ enum nl80211_sta_bss_param {
- * @NL80211_STA_INFO_STA_FLAGS: Contains a struct nl80211_sta_flag_update.
- * @NL80211_STA_INFO_BEACON_LOSS: count of times beacon loss was detected (u32)
- * @NL80211_STA_INFO_T_OFFSET: timing offset with respect to this STA (s64)
-+ * @NL80211_STA_INFO_CHAIN_SIGNAL: per-chain signal strength of last PPDU
-+ * @NL80211_STA_INFO_CHAIN_SIGNAL_AVG: per-chain signal strength average
- * @__NL80211_STA_INFO_AFTER_LAST: internal
- * @NL80211_STA_INFO_MAX: highest possible station info attribute
- */
-@@ -1768,6 +1862,8 @@ enum nl80211_sta_info {
- NL80211_STA_INFO_STA_FLAGS,
- NL80211_STA_INFO_BEACON_LOSS,
- NL80211_STA_INFO_T_OFFSET,
-+ NL80211_STA_INFO_CHAIN_SIGNAL,
-+ NL80211_STA_INFO_CHAIN_SIGNAL_AVG,
-
- /* keep last */
- __NL80211_STA_INFO_AFTER_LAST,
-@@ -2385,6 +2481,15 @@ enum nl80211_ac {
- #define NL80211_TXQ_Q_BE NL80211_AC_BE
- #define NL80211_TXQ_Q_BK NL80211_AC_BK
-
-+/**
-+ * enum nl80211_channel_type - channel type
-+ * @NL80211_CHAN_NO_HT: 20 MHz, non-HT channel
-+ * @NL80211_CHAN_HT20: 20 MHz HT channel
-+ * @NL80211_CHAN_HT40MINUS: HT40 channel, secondary channel
-+ * below the control channel
-+ * @NL80211_CHAN_HT40PLUS: HT40 channel, secondary channel
-+ * above the control channel
-+ */
- enum nl80211_channel_type {
- NL80211_CHAN_NO_HT,
- NL80211_CHAN_HT20,
-@@ -2393,6 +2498,32 @@ enum nl80211_channel_type {
- };
+@@ -2672,6 +2678,8 @@ enum nl80211_frequency_attr {
+ #define NL80211_FREQUENCY_ATTR_PASSIVE_SCAN NL80211_FREQUENCY_ATTR_NO_IR
+ #define NL80211_FREQUENCY_ATTR_NO_IBSS NL80211_FREQUENCY_ATTR_NO_IR
+ #define NL80211_FREQUENCY_ATTR_NO_IR NL80211_FREQUENCY_ATTR_NO_IR
++#define NL80211_FREQUENCY_ATTR_GO_CONCURRENT \
++ NL80211_FREQUENCY_ATTR_IR_CONCURRENT
/**
-+ * enum nl80211_chan_width - channel width definitions
-+ *
-+ * These values are used with the %NL80211_ATTR_CHANNEL_WIDTH
-+ * attribute.
-+ *
-+ * @NL80211_CHAN_WIDTH_20_NOHT: 20 MHz, non-HT channel
-+ * @NL80211_CHAN_WIDTH_20: 20 MHz HT channel
-+ * @NL80211_CHAN_WIDTH_40: 40 MHz channel, the %NL80211_ATTR_CENTER_FREQ1
-+ * attribute must be provided as well
-+ * @NL80211_CHAN_WIDTH_80: 80 MHz channel, the %NL80211_ATTR_CENTER_FREQ1
-+ * attribute must be provided as well
-+ * @NL80211_CHAN_WIDTH_80P80: 80+80 MHz channel, the %NL80211_ATTR_CENTER_FREQ1
-+ * and %NL80211_ATTR_CENTER_FREQ2 attributes must be provided as well
-+ * @NL80211_CHAN_WIDTH_160: 160 MHz channel, the %NL80211_ATTR_CENTER_FREQ1
-+ * attribute must be provided as well
-+ */
-+enum nl80211_chan_width {
-+ NL80211_CHAN_WIDTH_20_NOHT,
-+ NL80211_CHAN_WIDTH_20,
-+ NL80211_CHAN_WIDTH_40,
-+ NL80211_CHAN_WIDTH_80,
-+ NL80211_CHAN_WIDTH_80P80,
-+ NL80211_CHAN_WIDTH_160,
-+};
-+
-+/**
- * enum nl80211_bss - netlink attributes for a BSS
- *
- * @__NL80211_BSS_INVALID: invalid
-@@ -2460,6 +2591,7 @@ enum nl80211_bss_status {
- * @NL80211_AUTHTYPE_SHARED_KEY: Shared Key authentication (WEP only)
- * @NL80211_AUTHTYPE_FT: Fast BSS Transition (IEEE 802.11r)
- * @NL80211_AUTHTYPE_NETWORK_EAP: Network EAP (some Cisco APs and mainly LEAP)
-+ * @NL80211_AUTHTYPE_SAE: Simultaneous authentication of equals
- * @__NL80211_AUTHTYPE_NUM: internal
- * @NL80211_AUTHTYPE_MAX: maximum valid auth algorithm
- * @NL80211_AUTHTYPE_AUTOMATIC: determine automatically (if necessary by
-@@ -2471,6 +2603,7 @@ enum nl80211_auth_type {
- NL80211_AUTHTYPE_SHARED_KEY,
- NL80211_AUTHTYPE_FT,
- NL80211_AUTHTYPE_NETWORK_EAP,
-+ NL80211_AUTHTYPE_SAE,
-
- /* keep last */
- __NL80211_AUTHTYPE_NUM,
-@@ -2994,12 +3127,40 @@ enum nl80211_ap_sme_features {
- * @NL80211_FEATURE_CELL_BASE_REG_HINTS: This driver has been tested
- * to work properly to suppport receiving regulatory hints from
- * cellular base stations.
-+ * @NL80211_FEATURE_P2P_DEVICE_NEEDS_CHANNEL: If this is set, an active
-+ * P2P Device (%NL80211_IFTYPE_P2P_DEVICE) requires its own channel
-+ * in the interface combinations, even when it's only used for scan
-+ * and remain-on-channel. This could be due to, for example, the
-+ * remain-on-channel implementation requiring a channel context.
-+ * @NL80211_FEATURE_SAE: This driver supports simultaneous authentication of
-+ * equals (SAE) with user space SME (NL80211_CMD_AUTHENTICATE) in station
-+ * mode
-+ * @NL80211_FEATURE_LOW_PRIORITY_SCAN: This driver supports low priority scan
-+ * @NL80211_FEATURE_SCAN_FLUSH: Scan flush is supported
-+ * @NL80211_FEATURE_AP_SCAN: Support scanning using an AP vif
-+ * @NL80211_FEATURE_VIF_TXPOWER: The driver supports per-vif TX power setting
-+ * @NL80211_FEATURE_NEED_OBSS_SCAN: The driver expects userspace to perform
-+ * OBSS scans and generate 20/40 BSS coex reports. This flag is used only
-+ * for drivers implementing the CONNECT API, for AUTH/ASSOC it is implied.
-+ * @NL80211_FEATURE_P2P_GO_CTWIN: P2P GO implementation supports CT Window
-+ * setting
-+ * @NL80211_FEATURE_P2P_GO_OPPPS: P2P GO implementation supports opportunistic
-+ * powersave
- */
- enum nl80211_feature_flags {
-- NL80211_FEATURE_SK_TX_STATUS = 1 << 0,
-- NL80211_FEATURE_HT_IBSS = 1 << 1,
-- NL80211_FEATURE_INACTIVITY_TIMER = 1 << 2,
-- NL80211_FEATURE_CELL_BASE_REG_HINTS = 1 << 3,
-+ NL80211_FEATURE_SK_TX_STATUS = 1 << 0,
-+ NL80211_FEATURE_HT_IBSS = 1 << 1,
-+ NL80211_FEATURE_INACTIVITY_TIMER = 1 << 2,
-+ NL80211_FEATURE_CELL_BASE_REG_HINTS = 1 << 3,
-+ NL80211_FEATURE_P2P_DEVICE_NEEDS_CHANNEL = 1 << 4,
-+ NL80211_FEATURE_SAE = 1 << 5,
-+ NL80211_FEATURE_LOW_PRIORITY_SCAN = 1 << 6,
-+ NL80211_FEATURE_SCAN_FLUSH = 1 << 7,
-+ NL80211_FEATURE_AP_SCAN = 1 << 8,
-+ NL80211_FEATURE_VIF_TXPOWER = 1 << 9,
-+ NL80211_FEATURE_NEED_OBSS_SCAN = 1 << 10,
-+ NL80211_FEATURE_P2P_GO_CTWIN = 1 << 11,
-+ NL80211_FEATURE_P2P_GO_OPPPS = 1 << 12,
- };
-
- /**
-@@ -3023,4 +3184,36 @@ enum nl80211_probe_resp_offload_support_
- NL80211_PROBE_RESP_OFFLOAD_SUPPORT_80211U = 1<<3,
- };
+ * enum nl80211_bitrate_attr - bitrate attributes
+@@ -2830,7 +2838,7 @@ enum nl80211_sched_scan_match_attr {
+ * @NL80211_RRF_AUTO_BW: maximum available bandwidth should be calculated
+ * base on contiguous rules and wider channels will be allowed to cross
+ * multiple contiguous/overlapping frequency ranges.
+- * @NL80211_RRF_GO_CONCURRENT: See &NL80211_FREQUENCY_ATTR_GO_CONCURRENT
++ * @NL80211_RRF_IR_CONCURRENT: See &NL80211_FREQUENCY_ATTR_IR_CONCURRENT
+ * @NL80211_RRF_NO_HT40MINUS: channels can't be used in HT40- operation
+ * @NL80211_RRF_NO_HT40PLUS: channels can't be used in HT40+ operation
+ * @NL80211_RRF_NO_80MHZ: 80MHz operation not allowed
+@@ -2847,7 +2855,7 @@ enum nl80211_reg_rule_flags {
+ NL80211_RRF_NO_IR = 1<<7,
+ __NL80211_RRF_NO_IBSS = 1<<8,
+ NL80211_RRF_AUTO_BW = 1<<11,
+- NL80211_RRF_GO_CONCURRENT = 1<<12,
++ NL80211_RRF_IR_CONCURRENT = 1<<12,
+ NL80211_RRF_NO_HT40MINUS = 1<<13,
+ NL80211_RRF_NO_HT40PLUS = 1<<14,
+ NL80211_RRF_NO_80MHZ = 1<<15,
+@@ -2859,6 +2867,7 @@ enum nl80211_reg_rule_flags {
+ #define NL80211_RRF_NO_IR NL80211_RRF_NO_IR
+ #define NL80211_RRF_NO_HT40 (NL80211_RRF_NO_HT40MINUS |\
+ NL80211_RRF_NO_HT40PLUS)
++#define NL80211_RRF_GO_CONCURRENT NL80211_RRF_IR_CONCURRENT
-+/**
-+ * enum nl80211_connect_failed_reason - connection request failed reasons
-+ * @NL80211_CONN_FAIL_MAX_CLIENTS: Maximum number of clients that can be
-+ * handled by the AP is reached.
-+ * @NL80211_CONN_FAIL_BLOCKED_CLIENT: Client's MAC is in the AP's blocklist.
-+ */
-+enum nl80211_connect_failed_reason {
-+ NL80211_CONN_FAIL_MAX_CLIENTS,
-+ NL80211_CONN_FAIL_BLOCKED_CLIENT,
-+};
-+
-+/**
-+ * enum nl80211_scan_flags - scan request control flags
-+ *
-+ * Scan request control flags are used to control the handling
-+ * of NL80211_CMD_TRIGGER_SCAN and NL80211_CMD_START_SCHED_SCAN
-+ * requests.
-+ *
-+ * @NL80211_SCAN_FLAG_LOW_PRIORITY: scan request has low priority
-+ * @NL80211_SCAN_FLAG_FLUSH: flush cache before scanning
-+ * @NL80211_SCAN_FLAG_AP: force a scan even if the interface is configured
-+ * as AP and the beaconing has already been configured. This attribute is
-+ * dangerous because will destroy stations performance as a lot of frames
-+ * will be lost while scanning off-channel, therefore it must be used only
-+ * when really needed
-+ */
-+enum nl80211_scan_flags {
-+ NL80211_SCAN_FLAG_LOW_PRIORITY = 1<<0,
-+ NL80211_SCAN_FLAG_FLUSH = 1<<1,
-+ NL80211_SCAN_FLAG_AP = 1<<2,
-+};
-+
- #endif /* __LINUX_NL80211_H */
+ /* For backport compatibility with older userspace */
+ #define NL80211_RRF_NO_IR_ALL (NL80211_RRF_NO_IR | __NL80211_RRF_NO_IBSS)
projects / openwrt.git / blobdiff