msgid "Any zone"
msgstr ""
-msgid "Apply"
+msgid "Apply request failed with status <code>%h</code>"
msgstr ""
-msgid "Applying changes"
+msgid "Apply unchecked"
msgstr ""
msgid ""
msgid "Changes applied."
msgstr ""
+msgid "Changes have been reverted."
+msgstr ""
+
msgid "Changes the administrator password for accessing the device"
msgstr ""
msgid "Channel"
msgstr ""
+msgid ""
+"Channel %d is not available in the %s regulatory domain and has been auto-"
+"adjusted to %d."
+msgstr ""
+
msgid "Check"
msgstr ""
msgid "Configuration"
msgstr ""
-msgid "Configuration applied."
+msgid "Configuration files will be kept."
msgstr ""
-msgid "Configuration files will be kept."
+msgid "Configuration has been applied."
+msgstr ""
+
+msgid "Configuration has been rolled back!"
msgstr ""
msgid "Confirmation"
msgid "Connections"
msgstr ""
+msgid ""
+"Could not regain access to the device after applying the configuration "
+"changes. You might need to reconnect if you modified network related "
+"settings such as the IP address or wireless security credentials."
+msgstr ""
+
msgid "Country"
msgstr ""
msgstr ""
msgid ""
+"Custom files (certificates, scripts) may remain on the system. To prevent "
+"this, perform a factory-reset first."
+msgstr ""
+
+msgid ""
"Customizes the behaviour of the device <abbr title=\"Light Emitting Diode"
"\">LED</abbr>s if possible."
msgstr ""
msgid "Device unreachable"
msgstr ""
+msgid "Device unreachable!"
+msgstr ""
+
msgid "Diagnostics"
msgstr ""
msgid "Discard upstream RFC1918 responses"
msgstr ""
+msgid "Dismiss"
+msgstr ""
+
msgid "Displaying only packages containing"
msgstr ""
msgid "Enable"
msgstr ""
+msgid ""
+"Enable <abbr title=\"Internet Group Management Protocol\">IGMP</abbr> "
+"snooping"
+msgstr ""
+
msgid "Enable <abbr title=\"Spanning Tree Protocol\">STP</abbr>"
msgstr ""
msgid "Enabled"
msgstr ""
+msgid "Enables IGMP snooping on this bridge"
+msgstr ""
+
msgid ""
"Enables fast roaming among access points that belong to the same Mobility "
"Domain"
msgid "FT protocol"
msgstr ""
+msgid "Failed to confirm apply within %ds, waiting for rollback…"
+msgstr ""
+
msgid "File"
msgstr ""
msgid "Nslookup"
msgstr ""
+msgid "Number of cached DNS entries (max is 10000, 0 is no caching)"
+msgstr ""
+
msgid "OK"
msgstr ""
msgid "Obfuscated Password"
msgstr ""
+msgid "Obtain IPv6-Address"
+msgstr ""
+
msgid "Off-State Delay"
msgstr ""
msgid "Revert"
msgstr ""
+msgid "Revert changes"
+msgstr ""
+
+msgid "Revert request failed with status <code>%h</code>"
+msgstr ""
+
+msgid "Reverting configuration…"
+msgstr ""
+
msgid "Root"
msgstr ""
msgid "Save & Apply"
msgstr ""
-msgid "Save & Apply"
-msgstr ""
-
msgid "Scan"
msgstr ""
msgid "Size (.ipk)"
msgstr ""
+msgid "Size of DNS query cache"
+msgstr ""
+
msgid "Skip"
msgstr ""
msgid "Start priority"
msgstr ""
+msgid "Starting configuration apply…"
+msgstr ""
+
msgid "Startup"
msgstr ""
"Switch %q has an unknown topology - the VLAN settings might not be accurate."
msgstr ""
+msgid "Switch Port Mask"
+msgstr ""
+
msgid "Switch VLAN"
msgstr ""
msgstr ""
msgid ""
+"The device could not be reached within %d seconds after applying the pending "
+"changes, which caused the configuration to be rolled back for safety "
+"reasons. If you believe that the configuration changes are correct "
+"nonetheless, perform an unchecked configuration apply. Alternatively, you "
+"can dismiss this warning and edit changes before attempting to apply again, "
+"or revert all pending changes to keep the currently working configuration "
+"state."
+msgstr ""
+
+msgid ""
"The device file of the memory or partition (<abbr title=\"for example\">e.g."
"</abbr> <code>/dev/sda1</code>)"
msgstr ""
"\"Proceed\" below to start the flash procedure."
msgstr ""
-msgid "The following changes have been committed"
-msgstr ""
-
msgid "The following changes have been reverted"
msgstr ""
msgid "There are no active leases."
msgstr ""
-msgid "There are no pending changes to apply!"
+msgid "There are no changes to apply."
msgstr ""
msgid "There are no pending changes to revert!"
msgid ""
"This is the local endpoint address assigned by the tunnel broker, it usually "
-"ends with <code>:2</code>"
+"ends with <code>...:2/64</code>"
msgstr ""
msgid ""
msgid ""
"Use the <em>Add</em> Button to add a new lease entry. The <em>MAC-Address</"
-"em> indentifies the host, the <em>IPv4-Address</em> specifies to the fixed "
-"address to use and the <em>Hostname</em> is assigned as symbolic name to the "
-"requesting host. The optional <em>Lease time</em> can be used to set non-"
+"em> identifies the host, the <em>IPv4-Address</em> specifies the fixed "
+"address to use, and the <em>Hostname</em> is assigned as a symbolic name to "
+"the requesting host. The optional <em>Lease time</em> can be used to set non-"
"standard host-specific lease time, e.g. 12h, 3d or infinite."
msgstr ""
msgid "Waiting for command to complete..."
msgstr ""
+msgid "Waiting for configuration to get applied… %ds"
+msgstr ""
+
msgid "Waiting for device..."
msgstr ""
msgid "overlay"
msgstr ""
+msgid "random"
+msgstr ""
+
msgid "relay mode"
msgstr ""