X-Git-Url: https://git.archive.openwrt.org/?p=project%2Fluci.git;a=blobdiff_plain;f=i18n%2Fenglish%2Fluasrc%2Fi18n%2Fadmin-core.en.xml;h=9e07e80f05f6062ef6eba6e8a23e50e41a77c347;hp=ec78c773aeafac0b859078df751af77a9a755a79;hb=aa5c150f37acd749b2bd506257d0062e83811d22;hpb=7590274b21da38452bb4a4ad34b3ddf27385483e
diff --git a/i18n/english/luasrc/i18n/admin-core.en.xml b/i18n/english/luasrc/i18n/admin-core.en.xml
index ec78c773a..9e07e80f0 100644
--- a/i18n/english/luasrc/i18n/admin-core.en.xml
+++ b/i18n/english/luasrc/i18n/admin-core.en.xml
@@ -63,16 +63,18 @@
Here you can paste public SSH-Keys (one per line) for SSH public-key authentication.
Mount Points
Mount Points define at which point a memory device will be attached to the filesystem
-Mounted file systems"
-Used"
-Available"
+Mounted file systems
+Used
+Available
Mount Point
The device file of the memory or partition (e.g. /dev/sda1
)
The filesystem that was used to format the memory (e.g. ext3)
If your physical memory is insufficient unused data can be temporarily swapped to a swap-device resulting in a higher amount of usable RAM. Be aware that swapping data is a very slow process as the swap-device cannot be accessed with the high datarates of the RAM.
Firmware successfully flashed. Rebooting device...
Failed to flash
-Firmwareimage
+Firmware image
+Image received. About to start flashing process. DO NOT POWER OFF THE DEVICE!
+Writing firmware...
Flash Firmware
Keep configuration files
Sorry, this function is not (yet) available for your platform.
@@ -164,7 +166,12 @@
max. DHCP-Leases
additional hostfile
query port
+Enable TFTP-Server
+TFTP-Server Root
+Network Boot Image
Switch
+Active Connections
+This page gives an overview over currently active network connections.
Routes
In this area you find all network-related settings.
On most routers the network switch can be freely configured and splitted up into several VLANs.
@@ -184,17 +191,40 @@
Force
first address (last octet)
number of leased addresses -1
+DHCP-Options
+See "dnsmasq --help dhcp" for a list of available options.
Leases
Static Leases
Leasetime remaining
Active Leases
Point-to-Point Connections
Point-to-Point connections with PPPoE or PPTP are often used to connect a device over DSL or similar technologies to an internet access point.
+You need to install "comgt" for UMTS/GPRS, "ppp-mod-pppoe" for PPPoE, "ppp-mod-pppoa" for PPPoA or "pptp" for PPtP support
+You need to install "ppp-mod-pppoe" for PPPoE or "pptp" for PPtP support
PPTP-Server
Automatic Disconnect
Time (in seconds) after which an unused connection will be closed
Keep-Alive
Number of failed connection tests to initiate automatic reconnect
+Modem device
+The device node of your modem, e.g. /dev/ttyUSB0
+Replace default route
+Let pppd replace the current default route to use the PPP interface after successful connect
+Use peer DNS
+Configure the local DNS server to use the name servers adverticed by the PPP peer
+Enable IPv6 on PPP link
+Connect script
+Let pppd run this script after establishing the PPP link
+Disconnect script
+Let pppd run this script before tearing down the PPP link
+Additional pppd options
+Specify additional command line arguments for pppd here
+Access point (APN)
+PIN code
+Make sure that you provide the correct pin code here or you might lock your sim card!
+Service type
+Setup wait time
+Seconds to wait for the modem to become ready before attempting to connect
Routes specify over which interface and gateway a certain host or network can be reached.
Static Routes
Active IPv4-Routes
@@ -286,5 +316,9 @@
PEAP-Identity
PEAP-Password
Create Network
+Hostnames
+Host entries
+Hostname
+IP address