--- /dev/null
+Index: linux-2.6.22.1/drivers/mtd/nand/Kconfig
+===================================================================
+--- linux-2.6.22.1.orig/drivers/mtd/nand/Kconfig
++++ linux-2.6.22.1/drivers/mtd/nand/Kconfig
+@@ -81,6 +81,12 @@ config MTD_NAND_TS7250
+ help
+ Support for NAND flash on Technologic Systems TS-7250 platform.
+
++config MTD_NAND_RB100
++ tristate "NAND Flash device on RB100 board"
++ depends on MTD_NAND
++ help
++ Support for NAND flash on RB100 platform.
++
+ config MTD_NAND_IDS
+ tristate
+
+Index: linux-2.6.22.1/drivers/mtd/nand/Makefile
+===================================================================
+--- linux-2.6.22.1.orig/drivers/mtd/nand/Makefile
++++ linux-2.6.22.1/drivers/mtd/nand/Makefile
+@@ -10,6 +10,7 @@ obj-$(CONFIG_MTD_NAND_CAFE) += cafe_nan
+ obj-$(CONFIG_MTD_NAND_SPIA) += spia.o
+ obj-$(CONFIG_MTD_NAND_AMS_DELTA) += ams-delta.o
+ obj-$(CONFIG_MTD_NAND_TOTO) += toto.o
++obj-$(CONFIG_MTD_NAND_RB100) += rbmipsnand.o
+ obj-$(CONFIG_MTD_NAND_AUTCPU12) += autcpu12.o
+ obj-$(CONFIG_MTD_NAND_EDB7312) += edb7312.o
+ obj-$(CONFIG_MTD_NAND_AU1550) += au1550nd.o
+++ /dev/null
-Index: linux-2.6.22.1/drivers/serial/Makefile
-===================================================================
---- linux-2.6.22.1.orig/drivers/serial/Makefile
-+++ linux-2.6.22.1/drivers/serial/Makefile
-@@ -21,6 +21,7 @@ obj-$(CONFIG_SERIAL_8250_EXAR_ST16C554)
- obj-$(CONFIG_SERIAL_8250_HUB6) += 8250_hub6.o
- obj-$(CONFIG_SERIAL_8250_MCA) += 8250_mca.o
- obj-$(CONFIG_SERIAL_8250_AU1X00) += 8250_au1x00.o
-+obj-$(CONFIG_SERIAL_ADM5120) += adm5120_uart.o
- obj-$(CONFIG_SERIAL_AMBA_PL010) += amba-pl010.o
- obj-$(CONFIG_SERIAL_AMBA_PL011) += amba-pl011.o
- obj-$(CONFIG_SERIAL_CLPS711X) += clps711x.o
-Index: linux-2.6.22.1/include/linux/serial_core.h
-===================================================================
---- linux-2.6.22.1.orig/include/linux/serial_core.h
-+++ linux-2.6.22.1/include/linux/serial_core.h
-@@ -143,6 +143,9 @@
- #define PORT_KS8695 76
-
-
-+/* ADMtek ADM5120 SoC */
-+#define PORT_ADM5120 77
-+
- #ifdef __KERNEL__
-
- #include <linux/compiler.h>
-Index: linux-2.6.22.1/drivers/serial/Kconfig
-===================================================================
---- linux-2.6.22.1.orig/drivers/serial/Kconfig
-+++ linux-2.6.22.1/drivers/serial/Kconfig
-@@ -270,6 +270,22 @@ config SERIAL_8250_RM9K
-
- comment "Non-8250 serial port support"
-
-+config SERIAL_ADM5120
-+ bool "ADM5120 serial port support"
-+ depends on MIPS_ADM5120
-+ select SERIAL_CORE
-+ select SERIAL_CORE_CONSOLE
-+ help
-+ Driver for the on chip UARTs on the ADM5120 SoC
-+
-+config ADM5120_NR_UARTS
-+ int "Maximum number of ADM5120 serial ports"
-+ depends on SERIAL_ADM5120
-+ default "2"
-+ ---help---
-+ Set this to the number of serial ports you want the driver to
-+ support.
-+
- config SERIAL_AMBA_PL010
- tristate "ARM AMBA PL010 serial port support"
- depends on ARM_AMBA && (BROKEN || !ARCH_VERSATILE)
--- /dev/null
+Index: linux-2.6.22.1/drivers/serial/Makefile
+===================================================================
+--- linux-2.6.22.1.orig/drivers/serial/Makefile
++++ linux-2.6.22.1/drivers/serial/Makefile
+@@ -21,6 +21,7 @@ obj-$(CONFIG_SERIAL_8250_EXAR_ST16C554)
+ obj-$(CONFIG_SERIAL_8250_HUB6) += 8250_hub6.o
+ obj-$(CONFIG_SERIAL_8250_MCA) += 8250_mca.o
+ obj-$(CONFIG_SERIAL_8250_AU1X00) += 8250_au1x00.o
++obj-$(CONFIG_SERIAL_ADM5120) += adm5120_uart.o
+ obj-$(CONFIG_SERIAL_AMBA_PL010) += amba-pl010.o
+ obj-$(CONFIG_SERIAL_AMBA_PL011) += amba-pl011.o
+ obj-$(CONFIG_SERIAL_CLPS711X) += clps711x.o
+Index: linux-2.6.22.1/include/linux/serial_core.h
+===================================================================
+--- linux-2.6.22.1.orig/include/linux/serial_core.h
++++ linux-2.6.22.1/include/linux/serial_core.h
+@@ -143,6 +143,9 @@
+ #define PORT_KS8695 76
+
+
++/* ADMtek ADM5120 SoC */
++#define PORT_ADM5120 77
++
+ #ifdef __KERNEL__
+
+ #include <linux/compiler.h>
+Index: linux-2.6.22.1/drivers/serial/Kconfig
+===================================================================
+--- linux-2.6.22.1.orig/drivers/serial/Kconfig
++++ linux-2.6.22.1/drivers/serial/Kconfig
+@@ -270,6 +270,22 @@ config SERIAL_8250_RM9K
+
+ comment "Non-8250 serial port support"
+
++config SERIAL_ADM5120
++ bool "ADM5120 serial port support"
++ depends on MIPS_ADM5120
++ select SERIAL_CORE
++ select SERIAL_CORE_CONSOLE
++ help
++ Driver for the on chip UARTs on the ADM5120 SoC
++
++config ADM5120_NR_UARTS
++ int "Maximum number of ADM5120 serial ports"
++ depends on SERIAL_ADM5120
++ default "2"
++ ---help---
++ Set this to the number of serial ports you want the driver to
++ support.
++
+ config SERIAL_AMBA_PL010
+ tristate "ARM AMBA PL010 serial port support"
+ depends on ARM_AMBA && (BROKEN || !ARCH_VERSATILE)
+++ /dev/null
-Index: linux-2.6.22.1/drivers/mtd/Kconfig
-===================================================================
---- linux-2.6.22.1.orig/drivers/mtd/Kconfig
-+++ linux-2.6.22.1/drivers/mtd/Kconfig
-@@ -160,6 +160,22 @@ config MTD_AFS_PARTS
- for your particular device. It won't happen automatically. The
- 'armflash' map driver (CONFIG_MTD_ARMFLASH) does this, for example.
-
-+config MTD_MYLOADER_PARTS
-+ tristate "MyLoader partition parsing"
-+ depends on MIPS_ADM5120 && MTD_PARTITIONS
-+ ---help---
-+ MyLoader is a bootloader which allows the user to define partitions
-+ in flash devices, by putting a table in the second erase block
-+ on the device, similar to a partition table. This table gives the
-+ offsets and lengths of the user defined partitions.
-+
-+ If you need code which can detect and parse these tables, and
-+ register MTD 'partitions' corresponding to each image detected,
-+ enable this option.
-+
-+ You will still need the parsing functions to be called by the driver
-+ for your particular device. It won't happen automatically.
-+
- comment "User Modules And Translation Layers"
-
- config MTD_CHAR
-Index: linux-2.6.22.1/drivers/mtd/Makefile
-===================================================================
---- linux-2.6.22.1.orig/drivers/mtd/Makefile
-+++ linux-2.6.22.1/drivers/mtd/Makefile
-@@ -11,6 +11,7 @@ obj-$(CONFIG_MTD_CONCAT) += mtdconcat.o
- obj-$(CONFIG_MTD_REDBOOT_PARTS) += redboot.o
- obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o
- obj-$(CONFIG_MTD_AFS_PARTS) += afs.o
-+obj-$(CONFIG_MTD_MYLOADER_PARTS) += myloader.o
-
- # 'Users' - code which presents functionality to userspace.
- obj-$(CONFIG_MTD_CHAR) += mtdchar.o
--- /dev/null
+Index: linux-2.6.22.1/drivers/mtd/Kconfig
+===================================================================
+--- linux-2.6.22.1.orig/drivers/mtd/Kconfig
++++ linux-2.6.22.1/drivers/mtd/Kconfig
+@@ -160,6 +160,22 @@ config MTD_AFS_PARTS
+ for your particular device. It won't happen automatically. The
+ 'armflash' map driver (CONFIG_MTD_ARMFLASH) does this, for example.
+
++config MTD_MYLOADER_PARTS
++ tristate "MyLoader partition parsing"
++ depends on MIPS_ADM5120 && MTD_PARTITIONS
++ ---help---
++ MyLoader is a bootloader which allows the user to define partitions
++ in flash devices, by putting a table in the second erase block
++ on the device, similar to a partition table. This table gives the
++ offsets and lengths of the user defined partitions.
++
++ If you need code which can detect and parse these tables, and
++ register MTD 'partitions' corresponding to each image detected,
++ enable this option.
++
++ You will still need the parsing functions to be called by the driver
++ for your particular device. It won't happen automatically.
++
+ comment "User Modules And Translation Layers"
+
+ config MTD_CHAR
+Index: linux-2.6.22.1/drivers/mtd/Makefile
+===================================================================
+--- linux-2.6.22.1.orig/drivers/mtd/Makefile
++++ linux-2.6.22.1/drivers/mtd/Makefile
+@@ -11,6 +11,7 @@ obj-$(CONFIG_MTD_CONCAT) += mtdconcat.o
+ obj-$(CONFIG_MTD_REDBOOT_PARTS) += redboot.o
+ obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o
+ obj-$(CONFIG_MTD_AFS_PARTS) += afs.o
++obj-$(CONFIG_MTD_MYLOADER_PARTS) += myloader.o
+
+ # 'Users' - code which presents functionality to userspace.
+ obj-$(CONFIG_MTD_CHAR) += mtdchar.o
+++ /dev/null
-Index: linux-2.6.22.1/drivers/mtd/chips/cfi_cmdset_0002.c
-===================================================================
---- linux-2.6.22.1.orig/drivers/mtd/chips/cfi_cmdset_0002.c
-+++ linux-2.6.22.1/drivers/mtd/chips/cfi_cmdset_0002.c
-@@ -47,12 +47,19 @@
- #define MANUFACTURER_AMD 0x0001
- #define MANUFACTURER_ATMEL 0x001F
- #define MANUFACTURER_SST 0x00BF
-+#define MANUFACTURER_MACRONIX 0x00C2
- #define SST49LF004B 0x0060
- #define SST49LF040B 0x0050
- #define SST49LF008A 0x005a
- #define AT49BV6416 0x00d6
- #define MANUFACTURER_SAMSUNG 0x00ec
-
-+/* Macronix */
-+#define MX29LV160B 0x2249 /* MX29LV160 Bottom-boot chip */
-+#define MX29LV160T 0x22C4 /* MX29LV160 Top-boot chip */
-+#define MX29LV320B 0x22A8 /* MX29LV320 Bottom-boot chip */
-+#define MX29LV320T 0x22A7 /* MX29LV320 Top-boot chip */
-+
- static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *);
- static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
- static int cfi_amdstd_write_buffers(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
-@@ -217,6 +224,41 @@ static void fixup_use_atmel_lock(struct
- mtd->flags |= MTD_STUPID_LOCK;
- }
-
-+#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
-+/*
-+ * Some Macronix chips has no/bad bootblock information in the CFI table
-+ */
-+static void fixup_macronix_bootloc(struct mtd_info *mtd, void* param)
-+{
-+ struct map_info *map = mtd->priv;
-+ struct cfi_private *cfi = map->fldrv_priv;
-+ struct cfi_pri_amdstd *extp = cfi->cmdset_priv;
-+ __u8 t;
-+
-+ switch (cfi->id) {
-+ /* TODO: put affected chip ids here */
-+ case MX29LV160B:
-+ case MX29LV320B:
-+ t = 2; /* Bottom boot */
-+ break;
-+ case MX29LV160T:
-+ case MX29LV320T:
-+ t = 3; /* Top boot */
-+ break;
-+ default:
-+ return;
-+ }
-+
-+ if (extp->TopBottom == t)
-+ /* boot location detected by the CFI layer is correct */
-+ return;
-+
-+ extp->TopBottom = t;
-+ printk("%s: Macronix chip detected, id:0x%04X, boot location forced "
-+ "to %s\n", map->name, cfi->id, (t == 2) ? "bottom" : "top");
-+}
-+#endif /* CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC */
-+
- static struct cfi_fixup cfi_fixup_table[] = {
- #ifdef AMD_BOOTLOC_BUG
- { CFI_MFR_AMD, CFI_ID_ANY, fixup_amd_bootblock, NULL },
-@@ -231,6 +273,9 @@ static struct cfi_fixup cfi_fixup_table[
- { CFI_MFR_ANY, CFI_ID_ANY, fixup_use_write_buffers, NULL, },
- #endif
- { CFI_MFR_ATMEL, CFI_ID_ANY, fixup_convert_atmel_pri, NULL },
-+#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
-+ { MANUFACTURER_MACRONIX, CFI_ID_ANY, fixup_macronix_bootloc, NULL, },
-+#endif
- { 0, 0, NULL, NULL }
- };
- static struct cfi_fixup jedec_fixup_table[] = {
-Index: linux-2.6.22.1/drivers/mtd/chips/Kconfig
-===================================================================
---- linux-2.6.22.1.orig/drivers/mtd/chips/Kconfig
-+++ linux-2.6.22.1/drivers/mtd/chips/Kconfig
-@@ -196,6 +196,14 @@ config MTD_CFI_AMDSTD
- provides support for one of those command sets, used on chips
- including the AMD Am29LV320.
-
-+config MTD_CFI_FIXUP_MACRONIX_BOOTLOC
-+ bool "Force bottom boot for Macronix flash chips"
-+ depends on MTD_CFI_AMDSTD
-+ help
-+ Some Macronix flash chips have no/wrong boot-block location in the
-+ CFI table, and the driver may detect the type incorrectly. Select
-+ this if your board has such chip.
-+
- config MTD_CFI_STAA
- tristate "Support for ST (Advanced Architecture) flash chips"
- depends on MTD_GEN_PROBE
--- /dev/null
+Index: linux-2.6.22.1/drivers/mtd/chips/cfi_cmdset_0002.c
+===================================================================
+--- linux-2.6.22.1.orig/drivers/mtd/chips/cfi_cmdset_0002.c
++++ linux-2.6.22.1/drivers/mtd/chips/cfi_cmdset_0002.c
+@@ -47,12 +47,19 @@
+ #define MANUFACTURER_AMD 0x0001
+ #define MANUFACTURER_ATMEL 0x001F
+ #define MANUFACTURER_SST 0x00BF
++#define MANUFACTURER_MACRONIX 0x00C2
+ #define SST49LF004B 0x0060
+ #define SST49LF040B 0x0050
+ #define SST49LF008A 0x005a
+ #define AT49BV6416 0x00d6
+ #define MANUFACTURER_SAMSUNG 0x00ec
+
++/* Macronix */
++#define MX29LV160B 0x2249 /* MX29LV160 Bottom-boot chip */
++#define MX29LV160T 0x22C4 /* MX29LV160 Top-boot chip */
++#define MX29LV320B 0x22A8 /* MX29LV320 Bottom-boot chip */
++#define MX29LV320T 0x22A7 /* MX29LV320 Top-boot chip */
++
+ static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *);
+ static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
+ static int cfi_amdstd_write_buffers(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
+@@ -217,6 +224,41 @@ static void fixup_use_atmel_lock(struct
+ mtd->flags |= MTD_STUPID_LOCK;
+ }
+
++#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
++/*
++ * Some Macronix chips has no/bad bootblock information in the CFI table
++ */
++static void fixup_macronix_bootloc(struct mtd_info *mtd, void* param)
++{
++ struct map_info *map = mtd->priv;
++ struct cfi_private *cfi = map->fldrv_priv;
++ struct cfi_pri_amdstd *extp = cfi->cmdset_priv;
++ __u8 t;
++
++ switch (cfi->id) {
++ /* TODO: put affected chip ids here */
++ case MX29LV160B:
++ case MX29LV320B:
++ t = 2; /* Bottom boot */
++ break;
++ case MX29LV160T:
++ case MX29LV320T:
++ t = 3; /* Top boot */
++ break;
++ default:
++ return;
++ }
++
++ if (extp->TopBottom == t)
++ /* boot location detected by the CFI layer is correct */
++ return;
++
++ extp->TopBottom = t;
++ printk("%s: Macronix chip detected, id:0x%04X, boot location forced "
++ "to %s\n", map->name, cfi->id, (t == 2) ? "bottom" : "top");
++}
++#endif /* CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC */
++
+ static struct cfi_fixup cfi_fixup_table[] = {
+ #ifdef AMD_BOOTLOC_BUG
+ { CFI_MFR_AMD, CFI_ID_ANY, fixup_amd_bootblock, NULL },
+@@ -231,6 +273,9 @@ static struct cfi_fixup cfi_fixup_table[
+ { CFI_MFR_ANY, CFI_ID_ANY, fixup_use_write_buffers, NULL, },
+ #endif
+ { CFI_MFR_ATMEL, CFI_ID_ANY, fixup_convert_atmel_pri, NULL },
++#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
++ { MANUFACTURER_MACRONIX, CFI_ID_ANY, fixup_macronix_bootloc, NULL, },
++#endif
+ { 0, 0, NULL, NULL }
+ };
+ static struct cfi_fixup jedec_fixup_table[] = {
+Index: linux-2.6.22.1/drivers/mtd/chips/Kconfig
+===================================================================
+--- linux-2.6.22.1.orig/drivers/mtd/chips/Kconfig
++++ linux-2.6.22.1/drivers/mtd/chips/Kconfig
+@@ -196,6 +196,14 @@ config MTD_CFI_AMDSTD
+ provides support for one of those command sets, used on chips
+ including the AMD Am29LV320.
+
++config MTD_CFI_FIXUP_MACRONIX_BOOTLOC
++ bool "Force bottom boot for Macronix flash chips"
++ depends on MTD_CFI_AMDSTD
++ help
++ Some Macronix flash chips have no/wrong boot-block location in the
++ CFI table, and the driver may detect the type incorrectly. Select
++ this if your board has such chip.
++
+ config MTD_CFI_STAA
+ tristate "Support for ST (Advanced Architecture) flash chips"
+ depends on MTD_GEN_PROBE
+++ /dev/null
-Index: linux-2.6.22.1/drivers/mtd/chips/jedec_probe.c
-===================================================================
---- linux-2.6.22.1.orig/drivers/mtd/chips/jedec_probe.c
-+++ linux-2.6.22.1/drivers/mtd/chips/jedec_probe.c
-@@ -121,6 +121,10 @@
- #define UPD29F064115 0x221C
-
- /* PMC */
-+#define PM39LV512 0x001B
-+#define PM39LV010 0x001C
-+#define PM39LV020 0x003D
-+#define PM39LV040 0x003E
- #define PM49FL002 0x006D
- #define PM49FL004 0x006E
- #define PM49FL008 0x006A
-@@ -1246,6 +1250,58 @@ static const struct amd_flash_info jedec
- ERASEINFO(0x02000,2),
- ERASEINFO(0x04000,1),
- }
-+ }, {
-+ .mfr_id = MANUFACTURER_PMC,
-+ .dev_id = PM39LV512,
-+ .name = "PMC Pm39LV512",
-+ .uaddr = {
-+ [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
-+ },
-+ .DevSize = SIZE_64KiB,
-+ .CmdSet = P_ID_AMD_STD,
-+ .NumEraseRegions= 1,
-+ .regions = {
-+ ERASEINFO(0x01000,16),
-+ }
-+ }, {
-+ .mfr_id = MANUFACTURER_PMC,
-+ .dev_id = PM39LV010,
-+ .name = "PMC Pm39LV010",
-+ .uaddr = {
-+ [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
-+ },
-+ .DevSize = SIZE_128KiB,
-+ .CmdSet = P_ID_AMD_STD,
-+ .NumEraseRegions= 1,
-+ .regions = {
-+ ERASEINFO(0x01000,32),
-+ }
-+ }, {
-+ .mfr_id = MANUFACTURER_PMC,
-+ .dev_id = PM39LV020,
-+ .name = "PMC Pm39LV020",
-+ .uaddr = {
-+ [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
-+ },
-+ .DevSize = SIZE_256KiB,
-+ .CmdSet = P_ID_AMD_STD,
-+ .NumEraseRegions= 1,
-+ .regions = {
-+ ERASEINFO(0x01000,64),
-+ }
-+ }, {
-+ .mfr_id = MANUFACTURER_PMC,
-+ .dev_id = PM39LV040,
-+ .name = "PMC Pm39LV040",
-+ .uaddr = {
-+ [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
-+ },
-+ .DevSize = SIZE_512KiB,
-+ .CmdSet = P_ID_AMD_STD,
-+ .NumEraseRegions= 1,
-+ .regions = {
-+ ERASEINFO(0x01000,128),
-+ }
- }, {
- .mfr_id = MANUFACTURER_PMC,
- .dev_id = PM49FL002,
--- /dev/null
+Index: linux-2.6.22.1/drivers/mtd/chips/jedec_probe.c
+===================================================================
+--- linux-2.6.22.1.orig/drivers/mtd/chips/jedec_probe.c
++++ linux-2.6.22.1/drivers/mtd/chips/jedec_probe.c
+@@ -121,6 +121,10 @@
+ #define UPD29F064115 0x221C
+
+ /* PMC */
++#define PM39LV512 0x001B
++#define PM39LV010 0x001C
++#define PM39LV020 0x003D
++#define PM39LV040 0x003E
+ #define PM49FL002 0x006D
+ #define PM49FL004 0x006E
+ #define PM49FL008 0x006A
+@@ -1246,6 +1250,58 @@ static const struct amd_flash_info jedec
+ ERASEINFO(0x02000,2),
+ ERASEINFO(0x04000,1),
+ }
++ }, {
++ .mfr_id = MANUFACTURER_PMC,
++ .dev_id = PM39LV512,
++ .name = "PMC Pm39LV512",
++ .uaddr = {
++ [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
++ },
++ .DevSize = SIZE_64KiB,
++ .CmdSet = P_ID_AMD_STD,
++ .NumEraseRegions= 1,
++ .regions = {
++ ERASEINFO(0x01000,16),
++ }
++ }, {
++ .mfr_id = MANUFACTURER_PMC,
++ .dev_id = PM39LV010,
++ .name = "PMC Pm39LV010",
++ .uaddr = {
++ [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
++ },
++ .DevSize = SIZE_128KiB,
++ .CmdSet = P_ID_AMD_STD,
++ .NumEraseRegions= 1,
++ .regions = {
++ ERASEINFO(0x01000,32),
++ }
++ }, {
++ .mfr_id = MANUFACTURER_PMC,
++ .dev_id = PM39LV020,
++ .name = "PMC Pm39LV020",
++ .uaddr = {
++ [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
++ },
++ .DevSize = SIZE_256KiB,
++ .CmdSet = P_ID_AMD_STD,
++ .NumEraseRegions= 1,
++ .regions = {
++ ERASEINFO(0x01000,64),
++ }
++ }, {
++ .mfr_id = MANUFACTURER_PMC,
++ .dev_id = PM39LV040,
++ .name = "PMC Pm39LV040",
++ .uaddr = {
++ [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
++ },
++ .DevSize = SIZE_512KiB,
++ .CmdSet = P_ID_AMD_STD,
++ .NumEraseRegions= 1,
++ .regions = {
++ ERASEINFO(0x01000,128),
++ }
+ }, {
+ .mfr_id = MANUFACTURER_PMC,
+ .dev_id = PM49FL002,
+++ /dev/null
-Index: linux/drivers/serial/amba-pl010.c
-===================================================================
---- linux.orig/drivers/serial/amba-pl010.c
-+++ linux/drivers/serial/amba-pl010.c
-@@ -52,11 +52,10 @@
-
- #include <asm/io.h>
-
--#define UART_NR 8
--
- #define SERIAL_AMBA_MAJOR 204
- #define SERIAL_AMBA_MINOR 16
--#define SERIAL_AMBA_NR UART_NR
-+#define SERIAL_AMBA_NR CONFIG_SERIAL_AMBA_PL010_NUMPORTS
-+#define SERIAL_AMBA_NAME CONFIG_SERIAL_AMBA_PL010_PORTNAME
-
- #define AMBA_ISR_PASS_LIMIT 256
-
-@@ -82,7 +81,7 @@ static void pl010_stop_tx(struct uart_po
- struct uart_amba_port *uap = (struct uart_amba_port *)port;
- unsigned int cr;
-
-- cr = readb(uap->port.membase + UART010_CR);
-+ cr = readl(uap->port.membase + UART010_CR);
- cr &= ~UART010_CR_TIE;
- writel(cr, uap->port.membase + UART010_CR);
- }
-@@ -92,7 +91,7 @@ static void pl010_start_tx(struct uart_p
- struct uart_amba_port *uap = (struct uart_amba_port *)port;
- unsigned int cr;
-
-- cr = readb(uap->port.membase + UART010_CR);
-+ cr = readl(uap->port.membase + UART010_CR);
- cr |= UART010_CR_TIE;
- writel(cr, uap->port.membase + UART010_CR);
- }
-@@ -102,7 +101,7 @@ static void pl010_stop_rx(struct uart_po
- struct uart_amba_port *uap = (struct uart_amba_port *)port;
- unsigned int cr;
-
-- cr = readb(uap->port.membase + UART010_CR);
-+ cr = readl(uap->port.membase + UART010_CR);
- cr &= ~(UART010_CR_RIE | UART010_CR_RTIE);
- writel(cr, uap->port.membase + UART010_CR);
- }
-@@ -112,7 +111,7 @@ static void pl010_enable_ms(struct uart_
- struct uart_amba_port *uap = (struct uart_amba_port *)port;
- unsigned int cr;
-
-- cr = readb(uap->port.membase + UART010_CR);
-+ cr = readl(uap->port.membase + UART010_CR);
- cr |= UART010_CR_MSIE;
- writel(cr, uap->port.membase + UART010_CR);
- }
-@@ -122,9 +121,9 @@ static void pl010_rx_chars(struct uart_a
- struct tty_struct *tty = uap->port.info->tty;
- unsigned int status, ch, flag, rsr, max_count = 256;
-
-- status = readb(uap->port.membase + UART01x_FR);
-+ status = readl(uap->port.membase + UART01x_FR);
- while (UART_RX_DATA(status) && max_count--) {
-- ch = readb(uap->port.membase + UART01x_DR);
-+ ch = readl(uap->port.membase + UART01x_DR);
- flag = TTY_NORMAL;
-
- uap->port.icount.rx++;
-@@ -133,7 +132,7 @@ static void pl010_rx_chars(struct uart_a
- * Note that the error handling code is
- * out of the main execution path
- */
-- rsr = readb(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
-+ rsr = readl(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
- if (unlikely(rsr & UART01x_RSR_ANY)) {
- writel(0, uap->port.membase + UART01x_ECR);
-
-@@ -165,7 +164,7 @@ static void pl010_rx_chars(struct uart_a
- uart_insert_char(&uap->port, rsr, UART01x_RSR_OE, ch, flag);
-
- ignore_char:
-- status = readb(uap->port.membase + UART01x_FR);
-+ status = readl(uap->port.membase + UART01x_FR);
- }
- spin_unlock(&uap->port.lock);
- tty_flip_buffer_push(tty);
-@@ -210,7 +209,7 @@ static void pl010_modem_status(struct ua
-
- writel(0, uap->port.membase + UART010_ICR);
-
-- status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
-+ status = readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
-
- delta = status ^ uap->old_status;
- uap->old_status = status;
-@@ -238,7 +237,7 @@ static irqreturn_t pl010_int(int irq, vo
-
- spin_lock(&uap->port.lock);
-
-- status = readb(uap->port.membase + UART010_IIR);
-+ status = readl(uap->port.membase + UART010_IIR);
- if (status) {
- do {
- if (status & (UART010_IIR_RTIS | UART010_IIR_RIS))
-@@ -251,7 +250,7 @@ static irqreturn_t pl010_int(int irq, vo
- if (pass_counter-- == 0)
- break;
-
-- status = readb(uap->port.membase + UART010_IIR);
-+ status = readl(uap->port.membase + UART010_IIR);
- } while (status & (UART010_IIR_RTIS | UART010_IIR_RIS |
- UART010_IIR_TIS));
- handled = 1;
-@@ -265,7 +264,7 @@ static irqreturn_t pl010_int(int irq, vo
- static unsigned int pl010_tx_empty(struct uart_port *port)
- {
- struct uart_amba_port *uap = (struct uart_amba_port *)port;
-- unsigned int status = readb(uap->port.membase + UART01x_FR);
-+ unsigned int status = readl(uap->port.membase + UART01x_FR);
- return status & UART01x_FR_BUSY ? 0 : TIOCSER_TEMT;
- }
-
-@@ -275,7 +274,7 @@ static unsigned int pl010_get_mctrl(stru
- unsigned int result = 0;
- unsigned int status;
-
-- status = readb(uap->port.membase + UART01x_FR);
-+ status = readl(uap->port.membase + UART01x_FR);
- if (status & UART01x_FR_DCD)
- result |= TIOCM_CAR;
- if (status & UART01x_FR_DSR)
-@@ -301,7 +300,7 @@ static void pl010_break_ctl(struct uart_
- unsigned int lcr_h;
-
- spin_lock_irqsave(&uap->port.lock, flags);
-- lcr_h = readb(uap->port.membase + UART010_LCRH);
-+ lcr_h = readl(uap->port.membase + UART010_LCRH);
- if (break_state == -1)
- lcr_h |= UART01x_LCRH_BRK;
- else
-@@ -334,7 +333,7 @@ static int pl010_startup(struct uart_por
- /*
- * initialise the old status of the modem signals
- */
-- uap->old_status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
-+ uap->old_status = readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
-
- /*
- * Finally, enable interrupts
-@@ -365,7 +364,7 @@ static void pl010_shutdown(struct uart_p
- writel(0, uap->port.membase + UART010_CR);
-
- /* disable break condition and fifos */
-- writel(readb(uap->port.membase + UART010_LCRH) &
-+ writel(readl(uap->port.membase + UART010_LCRH) &
- ~(UART01x_LCRH_BRK | UART01x_LCRH_FEN),
- uap->port.membase + UART010_LCRH);
-
-@@ -387,7 +386,7 @@ pl010_set_termios(struct uart_port *port
- /*
- * Ask the core to calculate the divisor for us.
- */
-- baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16);
-+ baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16);
- quot = uart_get_divisor(port, baud);
-
- switch (termios->c_cflag & CSIZE) {
-@@ -450,7 +449,7 @@ pl010_set_termios(struct uart_port *port
- uap->port.ignore_status_mask |= UART_DUMMY_RSR_RX;
-
- /* first, disable everything */
-- old_cr = readb(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
-+ old_cr = readl(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
-
- if (UART_ENABLE_MS(port, termios->c_cflag))
- old_cr |= UART010_CR_MSIE;
-@@ -540,7 +539,7 @@ static struct uart_ops amba_pl010_pops =
- .verify_port = pl010_verify_port,
- };
-
--static struct uart_amba_port *amba_ports[UART_NR];
-+static struct uart_amba_port *amba_ports[SERIAL_AMBA_NR];
-
- #ifdef CONFIG_SERIAL_AMBA_PL010_CONSOLE
-
-@@ -550,7 +549,7 @@ static void pl010_console_putchar(struct
- unsigned int status;
-
- do {
-- status = readb(uap->port.membase + UART01x_FR);
-+ status = readl(uap->port.membase + UART01x_FR);
- barrier();
- } while (!UART_TX_READY(status));
- writel(ch, uap->port.membase + UART01x_DR);
-@@ -567,7 +566,7 @@ pl010_console_write(struct console *co,
- /*
- * First save the CR then disable the interrupts
- */
-- old_cr = readb(uap->port.membase + UART010_CR);
-+ old_cr = readl(uap->port.membase + UART010_CR);
- writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR);
-
- uart_console_write(&uap->port, s, count, pl010_console_putchar);
-@@ -577,7 +576,7 @@ pl010_console_write(struct console *co,
- * and restore the TCR
- */
- do {
-- status = readb(uap->port.membase + UART01x_FR);
-+ status = readl(uap->port.membase + UART01x_FR);
- barrier();
- } while (status & UART01x_FR_BUSY);
- writel(old_cr, uap->port.membase + UART010_CR);
-@@ -589,9 +588,9 @@ static void __init
- pl010_console_get_options(struct uart_amba_port *uap, int *baud,
- int *parity, int *bits)
- {
-- if (readb(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
-+ if (readl(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
- unsigned int lcr_h, quot;
-- lcr_h = readb(uap->port.membase + UART010_LCRH);
-+ lcr_h = readl(uap->port.membase + UART010_LCRH);
-
- *parity = 'n';
- if (lcr_h & UART01x_LCRH_PEN) {
-@@ -606,8 +605,8 @@ pl010_console_get_options(struct uart_am
- else
- *bits = 8;
-
-- quot = readb(uap->port.membase + UART010_LCRL) |
-- readb(uap->port.membase + UART010_LCRM) << 8;
-+ quot = readl(uap->port.membase + UART010_LCRL) |
-+ readl(uap->port.membase + UART010_LCRM) << 8;
- *baud = uap->port.uartclk / (16 * (quot + 1));
- }
- }
-@@ -625,7 +624,7 @@ static int __init pl010_console_setup(st
- * if so, search for the first available port that does have
- * console support.
- */
-- if (co->index >= UART_NR)
-+ if (co->index >= SERIAL_AMBA_NR)
- co->index = 0;
- uap = amba_ports[co->index];
- if (!uap)
-@@ -643,7 +642,7 @@ static int __init pl010_console_setup(st
-
- static struct uart_driver amba_reg;
- static struct console amba_console = {
-- .name = "ttyAM",
-+ .name = SERIAL_AMBA_NAME,
- .write = pl010_console_write,
- .device = uart_console_device,
- .setup = pl010_console_setup,
-@@ -659,11 +658,11 @@ static struct console amba_console = {
-
- static struct uart_driver amba_reg = {
- .owner = THIS_MODULE,
-- .driver_name = "ttyAM",
-- .dev_name = "ttyAM",
-+ .driver_name = SERIAL_AMBA_NAME,
-+ .dev_name = SERIAL_AMBA_NAME,
- .major = SERIAL_AMBA_MAJOR,
- .minor = SERIAL_AMBA_MINOR,
-- .nr = UART_NR,
-+ .nr = SERIAL_AMBA_NR,
- .cons = AMBA_CONSOLE,
- };
-
-Index: linux/drivers/serial/Kconfig
-===================================================================
---- linux.orig/drivers/serial/Kconfig
-+++ linux/drivers/serial/Kconfig
-@@ -293,10 +293,25 @@ config SERIAL_AMBA_PL010
- help
- This selects the ARM(R) AMBA(R) PrimeCell PL010 UART. If you have
- an Integrator/AP or Integrator/PP2 platform, or if you have a
-- Cirrus Logic EP93xx CPU, say Y or M here.
-+ Cirrus Logic EP93xx CPU or an Infineon ADM5120 SOC, say Y or M here.
-
- If unsure, say N.
-
-+config SERIAL_AMBA_PL010_NUMPORTS
-+ int "Maximum number of AMBA PL010 serial ports"
-+ depends on SERIAL_AMBA_PL010
-+ default "8"
-+ ---help---
-+ Set this to the number of serial ports you want the AMBA PL010 driver
-+ to support.
-+
-+config SERIAL_AMBA_PL010_PORTNAME
-+ string "Name of the AMBA PL010 serial ports"
-+ depends on SERIAL_AMBA_PL010
-+ default "ttyAM"
-+ ---help---
-+ ::: To be written :::
-+
- config SERIAL_AMBA_PL010_CONSOLE
- bool "Support for console on AMBA serial port"
- depends on SERIAL_AMBA_PL010=y
--- /dev/null
+Index: linux/drivers/serial/amba-pl010.c
+===================================================================
+--- linux.orig/drivers/serial/amba-pl010.c
++++ linux/drivers/serial/amba-pl010.c
+@@ -52,11 +52,10 @@
+
+ #include <asm/io.h>
+
+-#define UART_NR 8
+-
+ #define SERIAL_AMBA_MAJOR 204
+ #define SERIAL_AMBA_MINOR 16
+-#define SERIAL_AMBA_NR UART_NR
++#define SERIAL_AMBA_NR CONFIG_SERIAL_AMBA_PL010_NUMPORTS
++#define SERIAL_AMBA_NAME CONFIG_SERIAL_AMBA_PL010_PORTNAME
+
+ #define AMBA_ISR_PASS_LIMIT 256
+
+@@ -82,7 +81,7 @@ static void pl010_stop_tx(struct uart_po
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+ unsigned int cr;
+
+- cr = readb(uap->port.membase + UART010_CR);
++ cr = readl(uap->port.membase + UART010_CR);
+ cr &= ~UART010_CR_TIE;
+ writel(cr, uap->port.membase + UART010_CR);
+ }
+@@ -92,7 +91,7 @@ static void pl010_start_tx(struct uart_p
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+ unsigned int cr;
+
+- cr = readb(uap->port.membase + UART010_CR);
++ cr = readl(uap->port.membase + UART010_CR);
+ cr |= UART010_CR_TIE;
+ writel(cr, uap->port.membase + UART010_CR);
+ }
+@@ -102,7 +101,7 @@ static void pl010_stop_rx(struct uart_po
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+ unsigned int cr;
+
+- cr = readb(uap->port.membase + UART010_CR);
++ cr = readl(uap->port.membase + UART010_CR);
+ cr &= ~(UART010_CR_RIE | UART010_CR_RTIE);
+ writel(cr, uap->port.membase + UART010_CR);
+ }
+@@ -112,7 +111,7 @@ static void pl010_enable_ms(struct uart_
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+ unsigned int cr;
+
+- cr = readb(uap->port.membase + UART010_CR);
++ cr = readl(uap->port.membase + UART010_CR);
+ cr |= UART010_CR_MSIE;
+ writel(cr, uap->port.membase + UART010_CR);
+ }
+@@ -122,9 +121,9 @@ static void pl010_rx_chars(struct uart_a
+ struct tty_struct *tty = uap->port.info->tty;
+ unsigned int status, ch, flag, rsr, max_count = 256;
+
+- status = readb(uap->port.membase + UART01x_FR);
++ status = readl(uap->port.membase + UART01x_FR);
+ while (UART_RX_DATA(status) && max_count--) {
+- ch = readb(uap->port.membase + UART01x_DR);
++ ch = readl(uap->port.membase + UART01x_DR);
+ flag = TTY_NORMAL;
+
+ uap->port.icount.rx++;
+@@ -133,7 +132,7 @@ static void pl010_rx_chars(struct uart_a
+ * Note that the error handling code is
+ * out of the main execution path
+ */
+- rsr = readb(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
++ rsr = readl(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
+ if (unlikely(rsr & UART01x_RSR_ANY)) {
+ writel(0, uap->port.membase + UART01x_ECR);
+
+@@ -165,7 +164,7 @@ static void pl010_rx_chars(struct uart_a
+ uart_insert_char(&uap->port, rsr, UART01x_RSR_OE, ch, flag);
+
+ ignore_char:
+- status = readb(uap->port.membase + UART01x_FR);
++ status = readl(uap->port.membase + UART01x_FR);
+ }
+ spin_unlock(&uap->port.lock);
+ tty_flip_buffer_push(tty);
+@@ -210,7 +209,7 @@ static void pl010_modem_status(struct ua
+
+ writel(0, uap->port.membase + UART010_ICR);
+
+- status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
++ status = readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
+
+ delta = status ^ uap->old_status;
+ uap->old_status = status;
+@@ -238,7 +237,7 @@ static irqreturn_t pl010_int(int irq, vo
+
+ spin_lock(&uap->port.lock);
+
+- status = readb(uap->port.membase + UART010_IIR);
++ status = readl(uap->port.membase + UART010_IIR);
+ if (status) {
+ do {
+ if (status & (UART010_IIR_RTIS | UART010_IIR_RIS))
+@@ -251,7 +250,7 @@ static irqreturn_t pl010_int(int irq, vo
+ if (pass_counter-- == 0)
+ break;
+
+- status = readb(uap->port.membase + UART010_IIR);
++ status = readl(uap->port.membase + UART010_IIR);
+ } while (status & (UART010_IIR_RTIS | UART010_IIR_RIS |
+ UART010_IIR_TIS));
+ handled = 1;
+@@ -265,7 +264,7 @@ static irqreturn_t pl010_int(int irq, vo
+ static unsigned int pl010_tx_empty(struct uart_port *port)
+ {
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+- unsigned int status = readb(uap->port.membase + UART01x_FR);
++ unsigned int status = readl(uap->port.membase + UART01x_FR);
+ return status & UART01x_FR_BUSY ? 0 : TIOCSER_TEMT;
+ }
+
+@@ -275,7 +274,7 @@ static unsigned int pl010_get_mctrl(stru
+ unsigned int result = 0;
+ unsigned int status;
+
+- status = readb(uap->port.membase + UART01x_FR);
++ status = readl(uap->port.membase + UART01x_FR);
+ if (status & UART01x_FR_DCD)
+ result |= TIOCM_CAR;
+ if (status & UART01x_FR_DSR)
+@@ -301,7 +300,7 @@ static void pl010_break_ctl(struct uart_
+ unsigned int lcr_h;
+
+ spin_lock_irqsave(&uap->port.lock, flags);
+- lcr_h = readb(uap->port.membase + UART010_LCRH);
++ lcr_h = readl(uap->port.membase + UART010_LCRH);
+ if (break_state == -1)
+ lcr_h |= UART01x_LCRH_BRK;
+ else
+@@ -334,7 +333,7 @@ static int pl010_startup(struct uart_por
+ /*
+ * initialise the old status of the modem signals
+ */
+- uap->old_status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
++ uap->old_status = readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
+
+ /*
+ * Finally, enable interrupts
+@@ -365,7 +364,7 @@ static void pl010_shutdown(struct uart_p
+ writel(0, uap->port.membase + UART010_CR);
+
+ /* disable break condition and fifos */
+- writel(readb(uap->port.membase + UART010_LCRH) &
++ writel(readl(uap->port.membase + UART010_LCRH) &
+ ~(UART01x_LCRH_BRK | UART01x_LCRH_FEN),
+ uap->port.membase + UART010_LCRH);
+
+@@ -387,7 +386,7 @@ pl010_set_termios(struct uart_port *port
+ /*
+ * Ask the core to calculate the divisor for us.
+ */
+- baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16);
++ baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16);
+ quot = uart_get_divisor(port, baud);
+
+ switch (termios->c_cflag & CSIZE) {
+@@ -450,7 +449,7 @@ pl010_set_termios(struct uart_port *port
+ uap->port.ignore_status_mask |= UART_DUMMY_RSR_RX;
+
+ /* first, disable everything */
+- old_cr = readb(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
++ old_cr = readl(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
+
+ if (UART_ENABLE_MS(port, termios->c_cflag))
+ old_cr |= UART010_CR_MSIE;
+@@ -540,7 +539,7 @@ static struct uart_ops amba_pl010_pops =
+ .verify_port = pl010_verify_port,
+ };
+
+-static struct uart_amba_port *amba_ports[UART_NR];
++static struct uart_amba_port *amba_ports[SERIAL_AMBA_NR];
+
+ #ifdef CONFIG_SERIAL_AMBA_PL010_CONSOLE
+
+@@ -550,7 +549,7 @@ static void pl010_console_putchar(struct
+ unsigned int status;
+
+ do {
+- status = readb(uap->port.membase + UART01x_FR);
++ status = readl(uap->port.membase + UART01x_FR);
+ barrier();
+ } while (!UART_TX_READY(status));
+ writel(ch, uap->port.membase + UART01x_DR);
+@@ -567,7 +566,7 @@ pl010_console_write(struct console *co,
+ /*
+ * First save the CR then disable the interrupts
+ */
+- old_cr = readb(uap->port.membase + UART010_CR);
++ old_cr = readl(uap->port.membase + UART010_CR);
+ writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR);
+
+ uart_console_write(&uap->port, s, count, pl010_console_putchar);
+@@ -577,7 +576,7 @@ pl010_console_write(struct console *co,
+ * and restore the TCR
+ */
+ do {
+- status = readb(uap->port.membase + UART01x_FR);
++ status = readl(uap->port.membase + UART01x_FR);
+ barrier();
+ } while (status & UART01x_FR_BUSY);
+ writel(old_cr, uap->port.membase + UART010_CR);
+@@ -589,9 +588,9 @@ static void __init
+ pl010_console_get_options(struct uart_amba_port *uap, int *baud,
+ int *parity, int *bits)
+ {
+- if (readb(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
++ if (readl(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
+ unsigned int lcr_h, quot;
+- lcr_h = readb(uap->port.membase + UART010_LCRH);
++ lcr_h = readl(uap->port.membase + UART010_LCRH);
+
+ *parity = 'n';
+ if (lcr_h & UART01x_LCRH_PEN) {
+@@ -606,8 +605,8 @@ pl010_console_get_options(struct uart_am
+ else
+ *bits = 8;
+
+- quot = readb(uap->port.membase + UART010_LCRL) |
+- readb(uap->port.membase + UART010_LCRM) << 8;
++ quot = readl(uap->port.membase + UART010_LCRL) |
++ readl(uap->port.membase + UART010_LCRM) << 8;
+ *baud = uap->port.uartclk / (16 * (quot + 1));
+ }
+ }
+@@ -625,7 +624,7 @@ static int __init pl010_console_setup(st
+ * if so, search for the first available port that does have
+ * console support.
+ */
+- if (co->index >= UART_NR)
++ if (co->index >= SERIAL_AMBA_NR)
+ co->index = 0;
+ uap = amba_ports[co->index];
+ if (!uap)
+@@ -643,7 +642,7 @@ static int __init pl010_console_setup(st
+
+ static struct uart_driver amba_reg;
+ static struct console amba_console = {
+- .name = "ttyAM",
++ .name = SERIAL_AMBA_NAME,
+ .write = pl010_console_write,
+ .device = uart_console_device,
+ .setup = pl010_console_setup,
+@@ -659,11 +658,11 @@ static struct console amba_console = {
+
+ static struct uart_driver amba_reg = {
+ .owner = THIS_MODULE,
+- .driver_name = "ttyAM",
+- .dev_name = "ttyAM",
++ .driver_name = SERIAL_AMBA_NAME,
++ .dev_name = SERIAL_AMBA_NAME,
+ .major = SERIAL_AMBA_MAJOR,
+ .minor = SERIAL_AMBA_MINOR,
+- .nr = UART_NR,
++ .nr = SERIAL_AMBA_NR,
+ .cons = AMBA_CONSOLE,
+ };
+
+Index: linux/drivers/serial/Kconfig
+===================================================================
+--- linux.orig/drivers/serial/Kconfig
++++ linux/drivers/serial/Kconfig
+@@ -293,10 +293,25 @@ config SERIAL_AMBA_PL010
+ help
+ This selects the ARM(R) AMBA(R) PrimeCell PL010 UART. If you have
+ an Integrator/AP or Integrator/PP2 platform, or if you have a
+- Cirrus Logic EP93xx CPU, say Y or M here.
++ Cirrus Logic EP93xx CPU or an Infineon ADM5120 SOC, say Y or M here.
+
+ If unsure, say N.
+
++config SERIAL_AMBA_PL010_NUMPORTS
++ int "Maximum number of AMBA PL010 serial ports"
++ depends on SERIAL_AMBA_PL010
++ default "8"
++ ---help---
++ Set this to the number of serial ports you want the AMBA PL010 driver
++ to support.
++
++config SERIAL_AMBA_PL010_PORTNAME
++ string "Name of the AMBA PL010 serial ports"
++ depends on SERIAL_AMBA_PL010
++ default "ttyAM"
++ ---help---
++ ::: To be written :::
++
+ config SERIAL_AMBA_PL010_CONSOLE
+ bool "Support for console on AMBA serial port"
+ depends on SERIAL_AMBA_PL010=y
+++ /dev/null
-Index: linux/drivers/amba/bus.c
-===================================================================
---- linux.orig/drivers/amba/bus.c
-+++ linux/drivers/amba/bus.c
-@@ -17,6 +17,10 @@
- #include <asm/io.h>
- #include <asm/sizes.h>
-
-+#ifndef NO_IRQ
-+#define NO_IRQ (-1)
-+#endif
-+
- #define to_amba_device(d) container_of(d, struct amba_device, dev)
- #define to_amba_driver(d) container_of(d, struct amba_driver, drv)
-
--- /dev/null
+Index: linux/drivers/amba/bus.c
+===================================================================
+--- linux.orig/drivers/amba/bus.c
++++ linux/drivers/amba/bus.c
+@@ -17,6 +17,10 @@
+ #include <asm/io.h>
+ #include <asm/sizes.h>
+
++#ifndef NO_IRQ
++#define NO_IRQ (-1)
++#endif
++
+ #define to_amba_device(d) container_of(d, struct amba_device, dev)
+ #define to_amba_driver(d) container_of(d, struct amba_driver, drv)
+
+++ /dev/null
-Index: linux-2.6.22.1/drivers/mtd/nand/Kconfig
-===================================================================
---- linux-2.6.22.1.orig/drivers/mtd/nand/Kconfig
-+++ linux-2.6.22.1/drivers/mtd/nand/Kconfig
-@@ -81,6 +81,12 @@ config MTD_NAND_TS7250
- help
- Support for NAND flash on Technologic Systems TS-7250 platform.
-
-+config MTD_NAND_RB100
-+ tristate "NAND Flash device on RB100 board"
-+ depends on MTD_NAND
-+ help
-+ Support for NAND flash on RB100 platform.
-+
- config MTD_NAND_IDS
- tristate
-
-Index: linux-2.6.22.1/drivers/mtd/nand/Makefile
-===================================================================
---- linux-2.6.22.1.orig/drivers/mtd/nand/Makefile
-+++ linux-2.6.22.1/drivers/mtd/nand/Makefile
-@@ -10,6 +10,7 @@ obj-$(CONFIG_MTD_NAND_CAFE) += cafe_nan
- obj-$(CONFIG_MTD_NAND_SPIA) += spia.o
- obj-$(CONFIG_MTD_NAND_AMS_DELTA) += ams-delta.o
- obj-$(CONFIG_MTD_NAND_TOTO) += toto.o
-+obj-$(CONFIG_MTD_NAND_RB100) += rbmipsnand.o
- obj-$(CONFIG_MTD_NAND_AUTCPU12) += autcpu12.o
- obj-$(CONFIG_MTD_NAND_EDB7312) += edb7312.o
- obj-$(CONFIG_MTD_NAND_AU1550) += au1550nd.o
projects / openwrt.git / commitdiff