# CONFIG_MACH_D2NET_V2 is not set
# CONFIG_MACH_DB88F6281_BP is not set
CONFIG_MACH_DOCKSTAR=y
+CONFIG_MACH_GOFLEXNET=y
+CONFIG_MACH_GOFLEXHOME=y
# CONFIG_MACH_ESATA_SHEEVAPLUG is not set
# CONFIG_MACH_GURUPLUG is not set
CONFIG_MACH_ICONNECT=y
--- /dev/null
+/*
+ * arch/arm/mach-kirkwood/goflexhome-setup.c
+ *
+ * Seagate GoFlex Home Setup
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/ata_platform.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mv643xx_eth.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <mach/kirkwood.h>
+#include "common.h"
+#include "mpp.h"
+
+static struct mtd_partition goflexhome_nand_parts[] = {
+ {
+ .name = "u-boot",
+ .offset = 0,
+ .size = SZ_1M
+ }, {
+ .name = "uImage",
+ .offset = MTDPART_OFS_NXTBLK,
+ .size = SZ_2M + SZ_4M
+ }, {
+ .name = "root",
+ .offset = MTDPART_OFS_NXTBLK,
+ .size = MTDPART_SIZ_FULL
+ },
+};
+
+static struct mv643xx_eth_platform_data goflexhome_ge00_data = {
+ .phy_addr = MV643XX_ETH_PHY_ADDR(0),
+};
+
+static struct mv_sata_platform_data goflexhome_sata_data = {
+ .n_ports = 1,
+};
+
+static struct gpio_led goflexhome_led_pins[] = {
+ {
+ .name = "status:green:health",
+ .default_trigger = "default-on",
+ .gpio = 46,
+ .active_low = 1,
+ },
+ {
+ .name = "status:orange:fault",
+ .default_trigger = "none",
+ .gpio = 47,
+ .active_low = 1,
+ },
+ {
+ .name = "status:white:misc",
+ .default_trigger = "none",
+ .gpio = 40,
+ .active_low = 0,
+ }
+};
+
+static struct gpio_led_platform_data goflexhome_led_data = {
+ .leds = goflexhome_led_pins,
+ .num_leds = ARRAY_SIZE(goflexhome_led_pins),
+};
+
+static struct platform_device goflexhome_leds = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &goflexhome_led_data,
+ }
+};
+
+static unsigned int goflexhome_mpp_config[] __initdata = {
+ MPP29_GPIO, /* USB Power Enable */
+ MPP47_GPIO, /* LED Orange */
+ MPP46_GPIO, /* LED Green */
+ MPP40_GPIO, /* LED White */
+ 0
+};
+
+static void __init goflexhome_init(void)
+{
+ /*
+ * Basic setup. Needs to be called early.
+ */
+ kirkwood_init();
+
+ /* setup gpio pin select */
+ kirkwood_mpp_conf(goflexhome_mpp_config);
+
+ kirkwood_uart0_init();
+ kirkwood_nand_init(ARRAY_AND_SIZE(goflexhome_nand_parts), 40);
+
+ if (gpio_request(29, "USB Power Enable") != 0 ||
+ gpio_direction_output(29, 1) != 0)
+ printk(KERN_ERR "can't set up GPIO 29 (USB Power Enable)\n");
+ kirkwood_ehci_init();
+ kirkwood_ge00_init(&goflexhome_ge00_data);
+ kirkwood_sata_init(&goflexhome_sata_data);
+
+ platform_device_register(&goflexhome_leds);
+}
+
+MACHINE_START(GOFLEXHOME, "Seagate GoFlex Home")
+ /* Maintainer: Peter Carmichael <peterjncarm@ovi.com> */
+ .atag_offset = 0x100,
+ .init_machine = goflexhome_init,
+ .map_io = kirkwood_map_io,
+ .init_early = kirkwood_init_early,
+ .init_irq = kirkwood_init_irq,
+ .timer = &kirkwood_timer,
+ .restart = kirkwood_restart,
+MACHINE_END
--- /dev/null
+/*
+ * arch/arm/mach-kirkwood/goflexnet-setup.c
+ *
+ * Seagate GoFlex Net Setup
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/ata_platform.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mv643xx_eth.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <mach/kirkwood.h>
+#include "common.h"
+#include "mpp.h"
+
+static struct mtd_partition goflexnet_nand_parts[] = {
+ {
+ .name = "u-boot",
+ .offset = 0,
+ .size = SZ_1M
+ }, {
+ .name = "uImage",
+ .offset = MTDPART_OFS_NXTBLK,
+ .size = SZ_4M
+ }, {
+ .name = "rootfs",
+ .offset = MTDPART_OFS_NXTBLK,
+ .size = SZ_32M
+ }, {
+ .name = "data",
+ .offset = MTDPART_OFS_NXTBLK,
+ .size = MTDPART_SIZ_FULL
+ },
+};
+
+static struct mv643xx_eth_platform_data goflexnet_ge00_data = {
+ .phy_addr = MV643XX_ETH_PHY_ADDR(0),
+};
+
+static struct mv_sata_platform_data goflexnet_sata_data = {
+ .n_ports = 2,
+};
+
+static struct gpio_led goflexnet_led_pins[] = {
+ {
+ .name = "status:green:health",
+ .default_trigger = "default-on",
+ .gpio = 46, // 0x4000
+ .active_low = 1,
+ },
+ {
+ .name = "status:orange:fault",
+ .default_trigger = "none",
+ .gpio = 47, // 0x8000
+ .active_low = 1,
+ },
+ {
+ .name = "status:white:left0",
+ .default_trigger = "none",
+ .gpio = 42, // 0x0400
+ .active_low = 0,
+ },
+ {
+ .name = "status:white:left1",
+ .default_trigger = "none",
+ .gpio = 43, // 0x0800
+ .active_low = 0,
+ },
+ {
+ .name = "status:white:left2",
+ .default_trigger = "none",
+ .gpio = 44, // 0x1000
+ .active_low = 0,
+ },
+ {
+ .name = "status:white:left3",
+ .default_trigger = "none",
+ .gpio = 45, // 0x2000
+ .active_low = 0,
+ },
+ {
+ .name = "status:white:right0",
+ .default_trigger = "none",
+ .gpio = 38, // 0x0040
+ .active_low = 0,
+ },
+ {
+ .name = "status:white:right1",
+ .default_trigger = "none",
+ .gpio = 39, // 0x0080
+ .active_low = 0,
+ },
+ {
+ .name = "status:white:right2",
+ .default_trigger = "none",
+ .gpio = 40, // 0x0100
+ .active_low = 0,
+ },
+ {
+ .name = "status:white:right3",
+ .default_trigger = "none",
+ .gpio = 41, // 0x0200
+ .active_low = 0,
+ }
+};
+
+static struct gpio_led_platform_data goflexnet_led_data = {
+ .leds = goflexnet_led_pins,
+ .num_leds = ARRAY_SIZE(goflexnet_led_pins),
+};
+
+static struct platform_device goflexnet_leds = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &goflexnet_led_data,
+ }
+};
+
+static unsigned int goflexnet_mpp_config[] __initdata = {
+ MPP29_GPIO, /* USB Power Enable */
+ MPP47_GPIO, /* LED Orange */
+ MPP46_GPIO, /* LED Green */
+ MPP45_GPIO, /* LED Left Capacity 3 */
+ MPP44_GPIO, /* LED Left Capacity 2 */
+ MPP43_GPIO, /* LED Left Capacity 1 */
+ MPP42_GPIO, /* LED Left Capacity 0 */
+ MPP41_GPIO, /* LED Right Capacity 3 */
+ MPP40_GPIO, /* LED Right Capacity 2 */
+ MPP39_GPIO, /* LED Right Capacity 1 */
+ MPP38_GPIO, /* LED Right Capacity 0 */
+ 0
+};
+
+static void __init goflexnet_init(void)
+{
+ /*
+ * Basic setup. Needs to be called early.
+ */
+ kirkwood_init();
+
+ /* setup gpio pin select */
+ kirkwood_mpp_conf(goflexnet_mpp_config);
+
+ kirkwood_uart0_init();
+ kirkwood_nand_init(ARRAY_AND_SIZE(goflexnet_nand_parts), 40);
+
+ if (gpio_request(29, "USB Power Enable") != 0 ||
+ gpio_direction_output(29, 1) != 0)
+ printk(KERN_ERR "can't set up GPIO 29 (USB Power Enable)\n");
+ kirkwood_ehci_init();
+ kirkwood_ge00_init(&goflexnet_ge00_data);
+ kirkwood_sata_init(&goflexnet_sata_data);
+
+ platform_device_register(&goflexnet_leds);
+}
+
+MACHINE_START(GOFLEXNET, "Seagate GoFlex Net")
+ /* Maintainer: Peter Carmichael <peterjncarm@ovi.com> */
+ .atag_offset = 0x100,
+ .init_machine = goflexnet_init,
+ .map_io = kirkwood_map_io,
+ .init_early = kirkwood_init_early,
+ .init_irq = kirkwood_init_irq,
+ .timer = &kirkwood_timer,
+ .restart = kirkwood_restart,
+MACHINE_END
--- a/arch/arm/mach-kirkwood/Makefile
+++ b/arch/arm/mach-kirkwood/Makefile
-@@ -18,5 +18,8 @@ obj-$(CONFIG_MACH_D2NET_V2) += d2net_v2
+@@ -8,6 +8,8 @@ obj-$(CONFIG_MACH_SHEEVAPLUG) += sheeva
+ obj-$(CONFIG_MACH_ESATA_SHEEVAPLUG) += sheevaplug-setup.o
+ obj-$(CONFIG_MACH_GURUPLUG) += guruplug-setup.o
+ obj-$(CONFIG_MACH_DOCKSTAR) += dockstar-setup.o
++obj-$(CONFIG_MACH_GOFLEXNET) += goflexnet-setup.o
++obj-$(CONFIG_MACH_GOFLEXHOME) += goflexhome-setup.o
+ obj-$(CONFIG_MACH_TS219) += ts219-setup.o tsx1x-common.o
+ obj-$(CONFIG_MACH_TS41X) += ts41x-setup.o tsx1x-common.o
+ obj-$(CONFIG_MACH_OPENRD) += openrd-setup.o
+@@ -18,5 +20,8 @@ obj-$(CONFIG_MACH_D2NET_V2) += d2net_v2
obj-$(CONFIG_MACH_NET2BIG_V2) += netxbig_v2-setup.o lacie_v2-common.o
obj-$(CONFIG_MACH_NET5BIG_V2) += netxbig_v2-setup.o lacie_v2-common.o
obj-$(CONFIG_MACH_T5325) += t5325-setup.o
obj-$(CONFIG_CPU_IDLE) += cpuidle.o
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
-@@ -130,6 +130,24 @@ config MACH_T5325
+@@ -64,6 +64,18 @@ config MACH_DOCKSTAR
+ Say 'Y' here if you want your kernel to support the
+ Seagate FreeAgent DockStar.
+
++config MACH_GOFLEXNET
++ bool "Seagate GoFlex Net"
++ help
++ Say 'Y' here if you want your kernel to support the
++ Seagate GoFlex Net.
++
++config MACH_GOFLEXHOME
++ bool "Seagate GoFlex Home"
++ help
++ Say 'Y' here if you want your kernel to support the
++ Seagate GoFlex Home.
++
+ config MACH_OPENRD
+ bool
+
+@@ -130,6 +142,24 @@ config MACH_T5325
Say 'Y' here if you want your kernel to support the
HP t5325 Thin Client.
projects / openwrt.git / commitdiff