--- /dev/null
+Index: linux-2.6.22-rc6/arch/mips/Kconfig
+===================================================================
+--- linux-2.6.22-rc6.orig/arch/mips/Kconfig
++++ linux-2.6.22-rc6/arch/mips/Kconfig
+@@ -15,6 +15,17 @@ choice
+ prompt "System type"
+ default SGI_IP22
+
++config MIPS_ADM5120
++ bool "Support for ADM5120 SoC"
++ select SYS_HAS_CPU_MIPS32_R1
++ select DMA_NONCOHERENT
++ select HW_HAS_PCI
++ select IRQ_CPU
++ select SYS_SUPPORTS_LITTLE_ENDIAN
++ select SYS_SUPPORTS_BIG_ENDIAN
++ select SYS_SUPPORTS_32BIT_KERNEL
++ select GENERIC_GPIO
++
+ config MACH_ALCHEMY
+ bool "Alchemy processor based machines"
+
+@@ -658,6 +669,7 @@ config TOSHIBA_RBTX4938
+
+ endchoice
+
++source "arch/mips/adm5120/Kconfig"
+ source "arch/mips/au1000/Kconfig"
+ source "arch/mips/ddb5xxx/Kconfig"
+ source "arch/mips/gt64120/ev64120/Kconfig"
+Index: linux-2.6.22-rc6/arch/mips/Makefile
+===================================================================
+--- linux-2.6.22-rc6.orig/arch/mips/Makefile
++++ linux-2.6.22-rc6/arch/mips/Makefile
+@@ -165,6 +165,14 @@ cflags-$(CONFIG_MACH_JAZZ) += -Iinclude/
+ load-$(CONFIG_MACH_JAZZ) += 0xffffffff80080000
+
+ #
++# ADMtek 5120
++#
++
++core-$(CONFIG_MIPS_ADM5120) += arch/mips/adm5120/
++cflags-$(CONFIG_MIPS_ADM5120) += -Iinclude/asm-mips/mach-adm5120
++load-$(CONFIG_MIPS_ADM5120) += 0xffffffff80001000
++
++#
+ # Common Alchemy Au1x00 stuff
+ #
+ core-$(CONFIG_SOC_AU1X00) += arch/mips/au1000/common/
+Index: linux-2.6.22-rc6/include/asm-mips/bootinfo.h
+===================================================================
+--- linux-2.6.22-rc6.orig/include/asm-mips/bootinfo.h
++++ linux-2.6.22-rc6/include/asm-mips/bootinfo.h
+@@ -213,6 +213,57 @@
+ #define MACH_GROUP_NEC_EMMA2RH 25 /* NEC EMMA2RH (was 23) */
+ #define MACH_NEC_MARKEINS 0 /* NEC EMMA2RH Mark-eins */
+
++/*
++ * Valid machtype for group ADMtek ADM5120
++ */
++#define MACH_GROUP_ADM5120 26
++#define MACH_ADM5120_UNKNOWN 0 /* Unknown board */
++#define MACH_ADM5120_WP54G_WRT 1 /* Compex WP54G-WRT */
++#define MACH_ADM5120_WP54G 2 /* Compex WP54G */
++#define MACH_ADM5120_WP54AG 3 /* Compex WP54AG */
++#define MACH_ADM5120_WPP54G 4 /* Compex WPP54G */
++#define MACH_ADM5120_WPP54AG 5 /* Compex WPP54AG */
++#define MACH_ADM5120_NP28G 6 /* Compex NP28G */
++#define MACH_ADM5120_NP28GHS 7 /* Compex NP28G HotSpot */
++#define MACH_ADM5120_NP27G 8 /* Compex NP27G */
++#define MACH_ADM5120_WP54Gv1C 9 /* Compex WP54G version 1C */
++#define MACH_ADM5120_RB_111 10 /* Mikrotik RouterBOARD 111 */
++#define MACH_ADM5120_RB_112 11 /* Mikrotik RouterBOARD 112 */
++#define MACH_ADM5120_RB_133 12 /* Mikrotik RouterBOARD 133 */
++#define MACH_ADM5120_RB_133C 13 /* Mikrotik RouterBOARD 133c */
++#define MACH_ADM5120_RB_150 14 /* Mikrotik RouterBOARD 150 */
++#define MACH_ADM5120_RB_153 15 /* Mikrotik RouterBOARD 153 */
++#define MACH_ADM5120_HS100 16 /* ZyXEL HomeSafe 100/100W */
++#define MACH_ADM5120_P334 17 /* ZyXEL Prestige 334 */
++#define MACH_ADM5120_P334U 18 /* ZyXEL Prestige 334U */
++#define MACH_ADM5120_P334W 19 /* ZyXEL Prestige 334W */
++#define MACH_ADM5120_P334WH 20 /* ZyXEL Prestige 334WH */
++#define MACH_ADM5120_P334WHD 21 /* ZyXEL Prestige 334WHD */
++#define MACH_ADM5120_P334WT 22 /* ZyXEL Prestige 334WT */
++#define MACH_ADM5120_P335 23 /* ZyXEL Prestige 335/335WT */
++#define MACH_ADM5120_P335PLUS 24 /* ZyXEL Prestige 335Plus */
++#define MACH_ADM5120_P335U 25 /* ZyXEL Prestige 335U */
++#define MACH_ADM5120_ES2108 26 /* ZyXEL Ethernet Switch 2108 */
++#define MACH_ADM5120_ES2108F 27 /* ZyXEL Ethernet Switch 2108-F */
++#define MACH_ADM5120_ES2108G 28 /* ZyXEL Ethernet Switch 2108-G */
++#define MACH_ADM5120_ES2108LC 29 /* ZyXEL Ethernet Switch 2108-LC */
++#define MACH_ADM5120_ES2108PWR 30 /* ZyXEL Ethernet Switch 2108-PWR */
++#define MACH_ADM5120_ES2024A 31 /* ZyXEL Ethernet Switch 2024A */
++#define MACH_ADM5120_ES2024PWR 32 /* ZyXEL Ethernet Switch 2024PWR */
++#define MACH_ADM5120_CAS630 33 /* Cellvision CAS-630/630W */
++#define MACH_ADM5120_CAS670 34 /* Cellvision CAS-670/670W */
++#define MACH_ADM5120_CAS700 36 /* Cellvision CAS-700/700W */
++#define MACH_ADM5120_CAS771 37 /* Cellvision CAS-771/771W */
++#define MACH_ADM5120_CAS790 38 /* Cellvision CAS-790 */
++#define MACH_ADM5120_CAS861 39 /* Cellvision CAS-861/861W */
++#define MACH_ADM5120_NFS101U 40 /* Cellvision NFS-101U/101WU */
++#define MACH_ADM5120_NFS202U 41 /* Cellvision NFS-202U/202WU */
++#define MACH_ADM5120_EASY5120 43 /* Infineon EASY 5120 */
++#define MACH_ADM5120_EASY5120RT 44 /* Infineon EASY 5120-RT */
++#define MACH_ADM5120_EASY5120PATA 45 /* Infineon EASY 5120P-ATA */
++#define MACH_ADM5120_EASY83000 46 /* Infineon EASY-83000 */
++#define MACH_ADM5120_BR6104K 47 /* Edimax BR-6104K */
++
+ #define CL_SIZE COMMAND_LINE_SIZE
+
+ const char *get_system_type(void);
--- /dev/null
+Index: linux-2.6.22-rc6/drivers/mtd/maps/Kconfig
+===================================================================
+--- linux-2.6.22-rc6.orig/drivers/mtd/maps/Kconfig
++++ linux-2.6.22-rc6/drivers/mtd/maps/Kconfig
+@@ -620,5 +620,10 @@ config MTD_PLATRAM
+
+ This selection automatically selects the map_ram driver.
+
++config MTD_ADM5120
++ tristate "Map driver for ADMtek ADM5120 boards"
++ depends on MIPS_ADM5120
++ select MTD_CFI_AMDSTD
++
+ endmenu
+
+Index: linux-2.6.22-rc6/drivers/mtd/maps/Makefile
+===================================================================
+--- linux-2.6.22-rc6.orig/drivers/mtd/maps/Makefile
++++ linux-2.6.22-rc6/drivers/mtd/maps/Makefile
+@@ -47,6 +47,7 @@ obj-$(CONFIG_MTD_OCELOT) += ocelot.o
+ obj-$(CONFIG_MTD_SOLUTIONENGINE)+= solutionengine.o
+ obj-$(CONFIG_MTD_PCI) += pci.o
+ obj-$(CONFIG_MTD_ALCHEMY) += alchemy-flash.o
++obj-$(CONFIG_MTD_ADM5120) += adm5120_mtd.o
+ obj-$(CONFIG_MTD_LASAT) += lasat.o
+ obj-$(CONFIG_MTD_AUTCPU12) += autcpu12-nvram.o
+ obj-$(CONFIG_MTD_EDB7312) += edb7312.o
--- /dev/null
+Index: linux-2.6.22-rc6/drivers/net/Kconfig
+===================================================================
+--- linux-2.6.22-rc6.orig/drivers/net/Kconfig
++++ linux-2.6.22-rc6/drivers/net/Kconfig
+@@ -574,6 +574,10 @@ config MIPS_AU1X00_ENET
+ If you have an Alchemy Semi AU1X00 based system
+ say Y. Otherwise, say N.
+
++config MIPS_ADM5120_ENET
++ tristate "MIPS ADM5120 Ethernet switch support"
++ depends on NET_ETHERNET && MIPS_ADM5120
++
+ config NET_SB1250_MAC
+ tristate "SB1250 Ethernet support"
+ depends on NET_ETHERNET && SIBYTE_SB1xxx_SOC
+Index: linux-2.6.22-rc6/drivers/net/Makefile
+===================================================================
+--- linux-2.6.22-rc6.orig/drivers/net/Makefile
++++ linux-2.6.22-rc6/drivers/net/Makefile
+@@ -165,6 +165,7 @@ obj-$(CONFIG_SC92031) += sc92031.o
+ # This is also a 82596 and should probably be merged
+ obj-$(CONFIG_LP486E) += lp486e.o
+
++obj-$(CONFIG_MIPS_ADM5120_ENET) += adm5120sw.o
+ obj-$(CONFIG_ETH16I) += eth16i.o
+ obj-$(CONFIG_ZORRO8390) += zorro8390.o
+ obj-$(CONFIG_HPLANCE) += hplance.o 7990.o
--- /dev/null
+Index: linux-2.6.22-rc6/drivers/serial/Makefile
+===================================================================
+--- linux-2.6.22-rc6.orig/drivers/serial/Makefile
++++ linux-2.6.22-rc6/drivers/serial/Makefile
+@@ -21,6 +21,7 @@ obj-$(CONFIG_SERIAL_8250_EXAR_ST16C554)
+ obj-$(CONFIG_SERIAL_8250_HUB6) += 8250_hub6.o
+ obj-$(CONFIG_SERIAL_8250_MCA) += 8250_mca.o
+ obj-$(CONFIG_SERIAL_8250_AU1X00) += 8250_au1x00.o
++obj-$(CONFIG_SERIAL_ADM5120) += adm5120_uart.o
+ obj-$(CONFIG_SERIAL_AMBA_PL010) += amba-pl010.o
+ obj-$(CONFIG_SERIAL_AMBA_PL011) += amba-pl011.o
+ obj-$(CONFIG_SERIAL_CLPS711X) += clps711x.o
+Index: linux-2.6.22-rc6/include/linux/serial_core.h
+===================================================================
+--- linux-2.6.22-rc6.orig/include/linux/serial_core.h
++++ linux-2.6.22-rc6/include/linux/serial_core.h
+@@ -143,6 +143,9 @@
+ #define PORT_KS8695 76
+
+
++/* ADMtek ADM5120 SoC */
++#define PORT_ADM5120 77
++
+ #ifdef __KERNEL__
+
+ #include <linux/compiler.h>
+Index: linux-2.6.22-rc6/drivers/serial/Kconfig
+===================================================================
+--- linux-2.6.22-rc6.orig/drivers/serial/Kconfig
++++ linux-2.6.22-rc6/drivers/serial/Kconfig
+@@ -270,6 +270,22 @@ config SERIAL_8250_RM9K
+
+ comment "Non-8250 serial port support"
+
++config SERIAL_ADM5120
++ bool "ADM5120 serial port support"
++ depends on MIPS_ADM5120
++ select SERIAL_CORE
++ select SERIAL_CORE_CONSOLE
++ help
++ Driver for the on chip UARTs on the ADM5120 SoC
++
++config ADM5120_NR_UARTS
++ int "Maximum number of ADM5120 serial ports"
++ depends on SERIAL_ADM5120
++ default "2"
++ ---help---
++ Set this to the number of serial ports you want the driver to
++ support.
++
+ config SERIAL_AMBA_PL010
+ tristate "ARM AMBA PL010 serial port support"
+ depends on ARM_AMBA && (BROKEN || !ARCH_VERSATILE)
--- /dev/null
+Index: linux-2.6.22-rc6/drivers/usb/core/hub.c
+===================================================================
+--- linux-2.6.22-rc6.orig/drivers/usb/core/hub.c
++++ linux-2.6.22-rc6/drivers/usb/core/hub.c
+@@ -464,7 +464,7 @@ void usb_hub_tt_clear_buffer (struct usb
+ : (USB_ENDPOINT_XFER_BULK << 11);
+ if (usb_pipein (pipe))
+ clear->devinfo |= 1 << 15;
+-
++
+ /* tell keventd to clear state for this TT */
+ spin_lock_irqsave (&tt->lock, flags);
+ list_add_tail (&clear->clear_list, &tt->clear_list);
+@@ -540,7 +540,7 @@ static int hub_hub_status(struct usb_hub
+ "%s failed (err = %d)\n", __FUNCTION__, ret);
+ else {
+ *status = le16_to_cpu(hub->status->hub.wHubStatus);
+- *change = le16_to_cpu(hub->status->hub.wHubChange);
++ *change = le16_to_cpu(hub->status->hub.wHubChange);
+ ret = 0;
+ }
+ mutex_unlock(&hub->status_mutex);
+@@ -1424,7 +1424,7 @@ static int hub_port_status(struct usb_hu
+ ret = -EIO;
+ } else {
+ *status = le16_to_cpu(hub->status->port.wPortStatus);
+- *change = le16_to_cpu(hub->status->port.wPortChange);
++ *change = le16_to_cpu(hub->status->port.wPortChange);
+ ret = 0;
+ }
+ mutex_unlock(&hub->status_mutex);
+@@ -2007,7 +2007,7 @@ static inline int remote_wakeup(struct u
+ * Between connect detection and reset signaling there must be a delay
+ * of 100ms at least for debounce and power-settling. The corresponding
+ * timer shall restart whenever the downstream port detects a disconnect.
+- *
++ *
+ * Apparently there are some bluetooth and irda-dongles and a number of
+ * low-speed devices for which this debounce period may last over a second.
+ * Not covered by the spec - but easy to deal with.
+@@ -2142,7 +2142,7 @@ hub_port_init (struct usb_hub *hub, stru
+ goto fail;
+ }
+ oldspeed = udev->speed;
+-
++
+ /* USB 2.0 section 5.5.3 talks about ep0 maxpacket ...
+ * it's fixed size except for full speed devices.
+ * For Wireless USB devices, ep0 max packet is always 512 (tho
+@@ -2168,7 +2168,7 @@ hub_port_init (struct usb_hub *hub, stru
+ default:
+ goto fail;
+ }
+-
++
+ type = "";
+ switch (udev->speed) {
+ case USB_SPEED_LOW: speed = "low"; break;
+@@ -2194,7 +2194,7 @@ hub_port_init (struct usb_hub *hub, stru
+ udev->tt = &hub->tt;
+ udev->ttport = port1;
+ }
+-
++
+ /* Why interleave GET_DESCRIPTOR and SET_ADDRESS this way?
+ * Because device hardware and firmware is sometimes buggy in
+ * this area, and this is how Linux has done it for ages.
+@@ -2230,6 +2230,8 @@ hub_port_init (struct usb_hub *hub, stru
+ USB_DT_DEVICE << 8, 0,
+ buf, GET_DESCRIPTOR_BUFSIZE,
+ USB_CTRL_GET_TIMEOUT);
++printk(KERN_CRIT "usb_control_msg: %d %d %d (%d)\n", r, buf->bMaxPacketSize0,
++buf->bDescriptorType, USB_DT_DEVICE);
+ switch (buf->bMaxPacketSize0) {
+ case 8: case 16: case 32: case 64: case 255:
+ if (buf->bDescriptorType ==
+@@ -2281,7 +2283,7 @@ hub_port_init (struct usb_hub *hub, stru
+ udev->devnum, retval);
+ goto fail;
+ }
+-
++
+ /* cope with hardware quirkiness:
+ * - let SET_ADDRESS settle, some device hardware wants it
+ * - read ep0 maxpacket even for high and low speed,
+@@ -2318,7 +2320,7 @@ hub_port_init (struct usb_hub *hub, stru
+ udev->ep0.desc.wMaxPacketSize = cpu_to_le16(i);
+ ep0_reinit(udev);
+ }
+-
++
+ retval = usb_get_device_descriptor(udev, USB_DT_DEVICE_SIZE);
+ if (retval < (signed)sizeof(udev->descriptor)) {
+ dev_err(&udev->dev, "device descriptor read/%s, error %d\n",
+@@ -2416,7 +2418,7 @@ static void hub_port_connect_change(stru
+ struct device *hub_dev = hub->intfdev;
+ u16 wHubCharacteristics = le16_to_cpu(hub->descriptor->wHubCharacteristics);
+ int status, i;
+-
++
+ dev_dbg (hub_dev,
+ "port %d, status %04x, change %04x, %s\n",
+ port1, portstatus, portchange, portspeed (portstatus));
+@@ -2425,7 +2427,7 @@ static void hub_port_connect_change(stru
+ set_port_led(hub, port1, HUB_LED_AUTO);
+ hub->indicator[port1-1] = INDICATOR_AUTO;
+ }
+-
++
+ /* Disconnect any existing devices under this port */
+ if (hdev->children[port1-1])
+ usb_disconnect(&hdev->children[port1-1]);
+@@ -2455,7 +2457,7 @@ static void hub_port_connect_change(stru
+ if ((wHubCharacteristics & HUB_CHAR_LPSM) < 2
+ && !(portstatus & (1 << USB_PORT_FEAT_POWER)))
+ set_port_feature(hdev, port1, USB_PORT_FEAT_POWER);
+-
++
+ if (portstatus & USB_PORT_STAT_ENABLE)
+ goto done;
+ return;
+@@ -2535,7 +2537,7 @@ static void hub_port_connect_change(stru
+ goto loop_disable;
+ }
+ }
+-
++
+ /* check for devices running slower than they could */
+ if (le16_to_cpu(udev->descriptor.bcdUSB) >= 0x0200
+ && udev->speed == USB_SPEED_FULL
+@@ -2587,7 +2589,7 @@ loop:
+ if (status == -ENOTCONN)
+ break;
+ }
+-
++
+ done:
+ hub_port_disable(hub, port1, 1);
+ }
+@@ -2720,7 +2722,7 @@ static void hub_events(void)
+ * EM interference sometimes causes badly
+ * shielded USB devices to be shutdown by
+ * the hub, this hack enables them again.
+- * Works at least with mouse driver.
++ * Works at least with mouse driver.
+ */
+ if (!(portstatus & USB_PORT_STAT_ENABLE)
+ && !connect_change
+@@ -2750,7 +2752,7 @@ static void hub_events(void)
+ "resume on port %d, status %d\n",
+ i, ret);
+ }
+-
++
+ if (portchange & USB_PORT_STAT_C_OVERCURRENT) {
+ dev_err (hub_dev,
+ "over-current change on port %d\n",
+@@ -2985,7 +2987,7 @@ int usb_reset_device(struct usb_device *
+
+ if (ret < 0)
+ goto re_enumerate;
+-
++
+ /* Device might have changed firmware (DFU or similar) */
+ if (memcmp(&udev->descriptor, &descriptor, sizeof descriptor)
+ || config_descriptors_changed (udev)) {
+@@ -2993,7 +2995,7 @@ int usb_reset_device(struct usb_device *
+ udev->descriptor = descriptor; /* for disconnect() calls */
+ goto re_enumerate;
+ }
+-
++
+ if (!udev->actconfig)
+ goto done;
+
+@@ -3031,7 +3033,7 @@ int usb_reset_device(struct usb_device *
+
+ done:
+ return 0;
+-
++
+ re_enumerate:
+ hub_port_logical_disconnect(parent_hub, port1);
+ return -ENODEV;
+Index: linux-2.6.22-rc6/drivers/usb/host/Kconfig
+===================================================================
+--- linux-2.6.22-rc6.orig/drivers/usb/host/Kconfig
++++ linux-2.6.22-rc6/drivers/usb/host/Kconfig
+@@ -224,3 +224,6 @@ config USB_SL811_CS
+ To compile this driver as a module, choose M here: the
+ module will be called "sl811_cs".
+
++config USB_ADM5120_HCD
++ tristate "ADM5120 HCD support"
++ depends on USB && MIPS_ADM5120
+Index: linux-2.6.22-rc6/drivers/usb/host/Makefile
+===================================================================
+--- linux-2.6.22-rc6.orig/drivers/usb/host/Makefile
++++ linux-2.6.22-rc6/drivers/usb/host/Makefile
+@@ -8,6 +8,7 @@ endif
+
+ obj-$(CONFIG_PCI) += pci-quirks.o
+
++obj-$(CONFIG_USB_ADM5120_HCD) += adm5120-hcd.o
+ obj-$(CONFIG_USB_EHCI_HCD) += ehci-hcd.o
+ obj-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o
+ obj-$(CONFIG_USB_OHCI_HCD) += ohci-hcd.o
+Index: linux-2.6.22-rc6/drivers/usb/Kconfig
+===================================================================
+--- linux-2.6.22-rc6.orig/drivers/usb/Kconfig
++++ linux-2.6.22-rc6/drivers/usb/Kconfig
+@@ -88,8 +88,6 @@ source "drivers/usb/storage/Kconfig"
+
+ source "drivers/usb/image/Kconfig"
+
+-source "drivers/usb/mon/Kconfig"
+-
+ comment "USB port drivers"
+ depends on USB
+
+Index: linux-2.6.22-rc6/drivers/usb/Makefile
+===================================================================
+--- linux-2.6.22-rc6.orig/drivers/usb/Makefile
++++ linux-2.6.22-rc6/drivers/usb/Makefile
+@@ -16,6 +16,7 @@ obj-$(CONFIG_USB_UHCI_HCD) += host/
+ obj-$(CONFIG_USB_SL811_HCD) += host/
+ obj-$(CONFIG_USB_U132_HCD) += host/
+ obj-$(CONFIG_USB_OHCI_AT91) += host/
++obj-$(CONFIG_USB_ADM5120_HCD) += host/
+
+ obj-$(CONFIG_USB_ACM) += class/
+ obj-$(CONFIG_USB_PRINTER) += class/
--- /dev/null
+Index: linux-2.6.22-rc6/drivers/leds/Kconfig
+===================================================================
+--- linux-2.6.22-rc6.orig/drivers/leds/Kconfig
++++ linux-2.6.22-rc6/drivers/leds/Kconfig
+@@ -20,6 +20,27 @@ config LEDS_CLASS
+
+ comment "LED drivers"
+
++config LEDS_GPIO
++ tristate "LED support for LEDS on GPIO lines"
++ depends on LEDS_CLASS && GENERIC_GPIO
++ help
++ This option enables support for LEDs connected to GPIO lines
++
++config LEDS_ADM5120
++ tristate "LED Support for ADM5120 GPIO LEDs"
++ depends on LEDS_GPIO && MIPS_ADM5120
++ help
++ This option enables support for LEDs connected to GPIO lines
++ on ADM5120 SoC based platforms.
++
++config LEDS_ADM5120_EXPERIMENTAL
++ bool "Enable ADM5120 LEDs experimental code"
++ depends on LEDS_ADM5120
++
++config LEDS_ADM5120_DIAG
++ bool "Enable ADM5120 LEDs diagnostic mode"
++ depends on LEDS_ADM5120
++
+ config LEDS_CORGI
+ tristate "LED Support for the Sharp SL-C7x0 series"
+ depends on LEDS_CLASS && PXA_SHARP_C7xx
+Index: linux-2.6.22-rc6/drivers/leds/Makefile
+===================================================================
+--- linux-2.6.22-rc6.orig/drivers/leds/Makefile
++++ linux-2.6.22-rc6/drivers/leds/Makefile
+@@ -5,6 +5,8 @@ obj-$(CONFIG_LEDS_CLASS) += led-class.o
+ obj-$(CONFIG_LEDS_TRIGGERS) += led-triggers.o
+
+ # LED Platform Drivers
++obj-$(CONFIG_LEDS_GPIO) += leds-gpio.o
++obj-$(CONFIG_LEDS_ADM5120) += leds-adm5120.o
+ obj-$(CONFIG_LEDS_CORGI) += leds-corgi.o
+ obj-$(CONFIG_LEDS_LOCOMO) += leds-locomo.o
+ obj-$(CONFIG_LEDS_SPITZ) += leds-spitz.o
--- /dev/null
+Index: linux-2.6.22-rc6/arch/mips/pci/Makefile
+===================================================================
+--- linux-2.6.22-rc6.orig/arch/mips/pci/Makefile
++++ linux-2.6.22-rc6/arch/mips/pci/Makefile
+@@ -50,3 +50,4 @@ obj-$(CONFIG_TOSHIBA_RBTX4938) += fixup-
+ obj-$(CONFIG_VICTOR_MPC30X) += fixup-mpc30x.o
+ obj-$(CONFIG_ZAO_CAPCELLA) += fixup-capcella.o
+ obj-$(CONFIG_WR_PPMC) += fixup-wrppmc.o
++obj-$(CONFIG_PCI_ADM5120) += fixup-adm5120.o ops-adm5120.o pci-adm5120.o
+Index: linux-2.6.22-rc6/include/linux/pci_ids.h
+===================================================================
+--- linux-2.6.22-rc6.orig/include/linux/pci_ids.h
++++ linux-2.6.22-rc6/include/linux/pci_ids.h
+@@ -1712,6 +1712,9 @@
+ #define PCI_VENDOR_ID_ESDGMBH 0x12fe
+ #define PCI_DEVICE_ID_ESDGMBH_CPCIASIO4 0x0111
+
++#define PCI_VENDOR_ID_ADMTEK 0x1317
++#define PCI_DEVICE_ID_ADMTEK_ADM5120 0x5120
++
+ #define PCI_VENDOR_ID_SIIG 0x131f
+ #define PCI_SUBVENDOR_ID_SIIG 0x131f
+ #define PCI_DEVICE_ID_SIIG_1S_10x_550 0x1000
--- /dev/null
+Index: linux-2.6.22-rc6/include/asm-mips/byteorder.h
+===================================================================
+--- linux-2.6.22-rc6.orig/include/asm-mips/byteorder.h
++++ linux-2.6.22-rc6/include/asm-mips/byteorder.h
+@@ -58,6 +58,35 @@ static __inline__ __attribute_const__ __
+
+ #endif /* CONFIG_CPU_MIPSR2 */
+
++#ifdef CONFIG_ADM5120_HARDWARE_SWAB
++
++static __inline__ __attribute_const__ __u16 ___adm5120__swab16(__u16 x)
++{
++ __asm__ (
++ " sh %2, 0xCA(%1) \n"
++ " lhu %0, 0xCC(%1) \n"
++ : "=r" (x)
++ : "r" (0xB2000000), "r" (x));
++
++ return x;
++}
++
++static __inline__ __attribute_const__ __u32 ___adm5120__swab32(__u32 x)
++{
++ __asm__ (
++ " sw %2, 0xC8(%1) \n"
++ " lw %0, 0xCC(%1) \n"
++ : "=r" (x)
++ : "r" (0xB2000000), "r" (x));
++
++ return x;
++}
++
++#define __arch__swab16(x) ___adm5120__swab16(x)
++#define __arch__swab32(x) ___adm5120__swab32(x)
++
++#endif /* CONFIG_ADM5120_HARDWARE_SWAB */
++
+ #if !defined(__STRICT_ANSI__) || defined(__KERNEL__)
+ # define __BYTEORDER_HAS_U64__
+ # define __SWAB_64_THRU_32__
--- /dev/null
+Index: linux-2.6.22-rc6/drivers/mtd/Kconfig
+===================================================================
+--- linux-2.6.22-rc6.orig/drivers/mtd/Kconfig
++++ linux-2.6.22-rc6/drivers/mtd/Kconfig
+@@ -155,6 +155,22 @@ config MTD_AFS_PARTS
+ for your particular device. It won't happen automatically. The
+ 'armflash' map driver (CONFIG_MTD_ARMFLASH) does this, for example.
+
++config MTD_MYLOADER_PARTS
++ tristate "MyLoader partition parsing"
++ depends on MIPS_ADM5120 && MTD_PARTITIONS
++ ---help---
++ MyLoader is a bootloader which allows the user to define partitions
++ in flash devices, by putting a table in the second erase block
++ on the device, similar to a partition table. This table gives the
++ offsets and lengths of the user defined partitions.
++
++ If you need code which can detect and parse these tables, and
++ register MTD 'partitions' corresponding to each image detected,
++ enable this option.
++
++ You will still need the parsing functions to be called by the driver
++ for your particular device. It won't happen automatically.
++
+ comment "User Modules And Translation Layers"
+
+ config MTD_CHAR
+Index: linux-2.6.22-rc6/drivers/mtd/Makefile
+===================================================================
+--- linux-2.6.22-rc6.orig/drivers/mtd/Makefile
++++ linux-2.6.22-rc6/drivers/mtd/Makefile
+@@ -11,6 +11,7 @@ obj-$(CONFIG_MTD_CONCAT) += mtdconcat.o
+ obj-$(CONFIG_MTD_REDBOOT_PARTS) += redboot.o
+ obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o
+ obj-$(CONFIG_MTD_AFS_PARTS) += afs.o
++obj-$(CONFIG_MTD_MYLOADER_PARTS) += myloader.o
+
+ # 'Users' - code which presents functionality to userspace.
+ obj-$(CONFIG_MTD_CHAR) += mtdchar.o
--- /dev/null
+Index: linux-2.6.22-rc6/drivers/mtd/chips/cfi_cmdset_0002.c
+===================================================================
+--- linux-2.6.22-rc6.orig/drivers/mtd/chips/cfi_cmdset_0002.c
++++ linux-2.6.22-rc6/drivers/mtd/chips/cfi_cmdset_0002.c
+@@ -47,12 +47,17 @@
+ #define MANUFACTURER_AMD 0x0001
+ #define MANUFACTURER_ATMEL 0x001F
+ #define MANUFACTURER_SST 0x00BF
++#define MANUFACTURER_MACRONIX 0x00C2
+ #define SST49LF004B 0x0060
+ #define SST49LF040B 0x0050
+ #define SST49LF008A 0x005a
+ #define AT49BV6416 0x00d6
+ #define MANUFACTURER_SAMSUNG 0x00ec
+
++/* Macronix */
++#define MX29LV160B 0x2249 /* MX29LV160 Bottom-boot chip */
++#define MX29LV320B 0x22A8 /* MX29LV320 Bottom-boot chip */
++
+ static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *);
+ static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
+ static int cfi_amdstd_write_buffers(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
+@@ -217,6 +222,35 @@ static void fixup_use_atmel_lock(struct
+ mtd->flags |= MTD_STUPID_LOCK;
+ }
+
++#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
++/*
++ * Some Macronix chips has bad bootblock information in the CFI table
++ */
++static void fixup_macronix_bootloc(struct mtd_info *mtd, void* param)
++{
++ struct map_info *map = mtd->priv;
++ struct cfi_private *cfi = map->fldrv_priv;
++ struct cfi_pri_amdstd *extp = cfi->cmdset_priv;
++ __u8 major = extp->MajorVersion;
++ __u8 minor = extp->MinorVersion;
++
++ switch (cfi->id) {
++ /* TODO: put affected chip ids here */
++ case MX29LV160B:
++ case MX29LV320B:
++ if (((major << 8) | minor) != 0x3131)
++ break;
++
++ if (extp->TopBottom == 2)
++ break;
++
++ extp->TopBottom = 2; /* Bottom boot */
++ printk("%s: weird Macronix chip detected, id:0x%04X, boot location "
++ "forced to bottom\n", map->name, cfi->id);
++ }
++}
++#endif /* CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC */
++
+ static struct cfi_fixup cfi_fixup_table[] = {
+ #ifdef AMD_BOOTLOC_BUG
+ { CFI_MFR_AMD, CFI_ID_ANY, fixup_amd_bootblock, NULL },
+@@ -231,6 +265,9 @@ static struct cfi_fixup cfi_fixup_table[
+ { CFI_MFR_ANY, CFI_ID_ANY, fixup_use_write_buffers, NULL, },
+ #endif
+ { CFI_MFR_ATMEL, CFI_ID_ANY, fixup_convert_atmel_pri, NULL },
++#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
++ { MANUFACTURER_MACRONIX, CFI_ID_ANY, fixup_macronix_bootloc, NULL, },
++#endif
+ { 0, 0, NULL, NULL }
+ };
+ static struct cfi_fixup jedec_fixup_table[] = {
+Index: linux-2.6.22-rc6/drivers/mtd/chips/Kconfig
+===================================================================
+--- linux-2.6.22-rc6.orig/drivers/mtd/chips/Kconfig
++++ linux-2.6.22-rc6/drivers/mtd/chips/Kconfig
+@@ -196,6 +196,14 @@ config MTD_CFI_AMDSTD
+ provides support for one of those command sets, used on chips
+ including the AMD Am29LV320.
+
++config MTD_CFI_FIXUP_MACRONIX_BOOTLOC
++ bool "Force bottom boot for Macronix flash chips"
++ depends on MTD_CFI_AMDSTD
++ help
++ Some Macronix flash chips have wrong boot-block location in the
++ CFI table, and the driver may detect the type incorrectly. Select
++ this if your board has such chip.
++
+ config MTD_CFI_STAA
+ tristate "Support for ST (Advanced Architecture) flash chips"
+ depends on MTD_GEN_PROBE
--- /dev/null
+Index: linux-2.6.22-rc6/arch/mips/kernel/head.S
+===================================================================
+--- linux-2.6.22-rc6.orig/arch/mips/kernel/head.S
++++ linux-2.6.22-rc6/arch/mips/kernel/head.S
+@@ -129,14 +129,19 @@
+ #endif
+ .endm
+
+-
+ j kernel_entry
+ nop
+-
++ nop
++
+ /*
+ * Reserved space for exception handlers.
+ * Necessary for machines which link their kernels at KSEG0.
++ * Use as temporary storage for the kernel command line, so that it
++ * can be updated easily without having to relink the kernel.
+ */
++
++EXPORT(_image_cmdline)
++ .ascii "CMDLINE:"
+ .align 10
+
+ EXPORT(stext) # used for profiling
--- /dev/null
+Index: linux-2.6.22-rc6/drivers/mtd/nand/Kconfig
+===================================================================
+--- linux-2.6.22-rc6.orig/drivers/mtd/nand/Kconfig
++++ linux-2.6.22-rc6/drivers/mtd/nand/Kconfig
+@@ -81,6 +81,12 @@ config MTD_NAND_TS7250
+ help
+ Support for NAND flash on Technologic Systems TS-7250 platform.
+
++config MTD_NAND_RB100
++ tristate "NAND Flash device on RB100 board"
++ depends on MTD_NAND
++ help
++ Support for NAND flash on RB100 platform.
++
+ config MTD_NAND_IDS
+ tristate
+
+Index: linux-2.6.22-rc6/drivers/mtd/nand/Makefile
+===================================================================
+--- linux-2.6.22-rc6.orig/drivers/mtd/nand/Makefile
++++ linux-2.6.22-rc6/drivers/mtd/nand/Makefile
+@@ -10,6 +10,7 @@ obj-$(CONFIG_MTD_NAND_CAFE) += cafe_nan
+ obj-$(CONFIG_MTD_NAND_SPIA) += spia.o
+ obj-$(CONFIG_MTD_NAND_AMS_DELTA) += ams-delta.o
+ obj-$(CONFIG_MTD_NAND_TOTO) += toto.o
++obj-$(CONFIG_MTD_NAND_RB100) += rbmipsnand.o
+ obj-$(CONFIG_MTD_NAND_AUTCPU12) += autcpu12.o
+ obj-$(CONFIG_MTD_NAND_EDB7312) += edb7312.o
+ obj-$(CONFIG_MTD_NAND_AU1550) += au1550nd.o
+++ /dev/null
-Index: linux-2.6.22-rc6/arch/mips/Kconfig
-===================================================================
---- linux-2.6.22-rc6.orig/arch/mips/Kconfig
-+++ linux-2.6.22-rc6/arch/mips/Kconfig
-@@ -15,6 +15,17 @@ choice
- prompt "System type"
- default SGI_IP22
-
-+config MIPS_ADM5120
-+ bool "Support for ADM5120 SoC"
-+ select SYS_HAS_CPU_MIPS32_R1
-+ select DMA_NONCOHERENT
-+ select HW_HAS_PCI
-+ select IRQ_CPU
-+ select SYS_SUPPORTS_LITTLE_ENDIAN
-+ select SYS_SUPPORTS_BIG_ENDIAN
-+ select SYS_SUPPORTS_32BIT_KERNEL
-+ select GENERIC_GPIO
-+
- config MACH_ALCHEMY
- bool "Alchemy processor based machines"
-
-@@ -658,6 +669,7 @@ config TOSHIBA_RBTX4938
-
- endchoice
-
-+source "arch/mips/adm5120/Kconfig"
- source "arch/mips/au1000/Kconfig"
- source "arch/mips/ddb5xxx/Kconfig"
- source "arch/mips/gt64120/ev64120/Kconfig"
-Index: linux-2.6.22-rc6/arch/mips/Makefile
-===================================================================
---- linux-2.6.22-rc6.orig/arch/mips/Makefile
-+++ linux-2.6.22-rc6/arch/mips/Makefile
-@@ -165,6 +165,14 @@ cflags-$(CONFIG_MACH_JAZZ) += -Iinclude/
- load-$(CONFIG_MACH_JAZZ) += 0xffffffff80080000
-
- #
-+# ADMtek 5120
-+#
-+
-+core-$(CONFIG_MIPS_ADM5120) += arch/mips/adm5120/
-+cflags-$(CONFIG_MIPS_ADM5120) += -Iinclude/asm-mips/mach-adm5120
-+load-$(CONFIG_MIPS_ADM5120) += 0xffffffff80001000
-+
-+#
- # Common Alchemy Au1x00 stuff
- #
- core-$(CONFIG_SOC_AU1X00) += arch/mips/au1000/common/
-Index: linux-2.6.22-rc6/include/asm-mips/bootinfo.h
-===================================================================
---- linux-2.6.22-rc6.orig/include/asm-mips/bootinfo.h
-+++ linux-2.6.22-rc6/include/asm-mips/bootinfo.h
-@@ -213,6 +213,57 @@
- #define MACH_GROUP_NEC_EMMA2RH 25 /* NEC EMMA2RH (was 23) */
- #define MACH_NEC_MARKEINS 0 /* NEC EMMA2RH Mark-eins */
-
-+/*
-+ * Valid machtype for group ADMtek ADM5120
-+ */
-+#define MACH_GROUP_ADM5120 26
-+#define MACH_ADM5120_UNKNOWN 0 /* Unknown board */
-+#define MACH_ADM5120_WP54G_WRT 1 /* Compex WP54G-WRT */
-+#define MACH_ADM5120_WP54G 2 /* Compex WP54G */
-+#define MACH_ADM5120_WP54AG 3 /* Compex WP54AG */
-+#define MACH_ADM5120_WPP54G 4 /* Compex WPP54G */
-+#define MACH_ADM5120_WPP54AG 5 /* Compex WPP54AG */
-+#define MACH_ADM5120_NP28G 6 /* Compex NP28G */
-+#define MACH_ADM5120_NP28GHS 7 /* Compex NP28G HotSpot */
-+#define MACH_ADM5120_NP27G 8 /* Compex NP27G */
-+#define MACH_ADM5120_WP54Gv1C 9 /* Compex WP54G version 1C */
-+#define MACH_ADM5120_RB_111 10 /* Mikrotik RouterBOARD 111 */
-+#define MACH_ADM5120_RB_112 11 /* Mikrotik RouterBOARD 112 */
-+#define MACH_ADM5120_RB_133 12 /* Mikrotik RouterBOARD 133 */
-+#define MACH_ADM5120_RB_133C 13 /* Mikrotik RouterBOARD 133c */
-+#define MACH_ADM5120_RB_150 14 /* Mikrotik RouterBOARD 150 */
-+#define MACH_ADM5120_RB_153 15 /* Mikrotik RouterBOARD 153 */
-+#define MACH_ADM5120_HS100 16 /* ZyXEL HomeSafe 100/100W */
-+#define MACH_ADM5120_P334 17 /* ZyXEL Prestige 334 */
-+#define MACH_ADM5120_P334U 18 /* ZyXEL Prestige 334U */
-+#define MACH_ADM5120_P334W 19 /* ZyXEL Prestige 334W */
-+#define MACH_ADM5120_P334WH 20 /* ZyXEL Prestige 334WH */
-+#define MACH_ADM5120_P334WHD 21 /* ZyXEL Prestige 334WHD */
-+#define MACH_ADM5120_P334WT 22 /* ZyXEL Prestige 334WT */
-+#define MACH_ADM5120_P335 23 /* ZyXEL Prestige 335/335WT */
-+#define MACH_ADM5120_P335PLUS 24 /* ZyXEL Prestige 335Plus */
-+#define MACH_ADM5120_P335U 25 /* ZyXEL Prestige 335U */
-+#define MACH_ADM5120_ES2108 26 /* ZyXEL Ethernet Switch 2108 */
-+#define MACH_ADM5120_ES2108F 27 /* ZyXEL Ethernet Switch 2108-F */
-+#define MACH_ADM5120_ES2108G 28 /* ZyXEL Ethernet Switch 2108-G */
-+#define MACH_ADM5120_ES2108LC 29 /* ZyXEL Ethernet Switch 2108-LC */
-+#define MACH_ADM5120_ES2108PWR 30 /* ZyXEL Ethernet Switch 2108-PWR */
-+#define MACH_ADM5120_ES2024A 31 /* ZyXEL Ethernet Switch 2024A */
-+#define MACH_ADM5120_ES2024PWR 32 /* ZyXEL Ethernet Switch 2024PWR */
-+#define MACH_ADM5120_CAS630 33 /* Cellvision CAS-630/630W */
-+#define MACH_ADM5120_CAS670 34 /* Cellvision CAS-670/670W */
-+#define MACH_ADM5120_CAS700 36 /* Cellvision CAS-700/700W */
-+#define MACH_ADM5120_CAS771 37 /* Cellvision CAS-771/771W */
-+#define MACH_ADM5120_CAS790 38 /* Cellvision CAS-790 */
-+#define MACH_ADM5120_CAS861 39 /* Cellvision CAS-861/861W */
-+#define MACH_ADM5120_NFS101U 40 /* Cellvision NFS-101U/101WU */
-+#define MACH_ADM5120_NFS202U 41 /* Cellvision NFS-202U/202WU */
-+#define MACH_ADM5120_EASY5120 43 /* Infineon EASY 5120 */
-+#define MACH_ADM5120_EASY5120RT 44 /* Infineon EASY 5120-RT */
-+#define MACH_ADM5120_EASY5120PATA 45 /* Infineon EASY 5120P-ATA */
-+#define MACH_ADM5120_EASY83000 46 /* Infineon EASY-83000 */
-+#define MACH_ADM5120_BR6104K 47 /* Edimax BR-6104K */
-+
- #define CL_SIZE COMMAND_LINE_SIZE
-
- const char *get_system_type(void);
+++ /dev/null
-Index: linux-2.6.22-rc6/drivers/mtd/maps/Kconfig
-===================================================================
---- linux-2.6.22-rc6.orig/drivers/mtd/maps/Kconfig
-+++ linux-2.6.22-rc6/drivers/mtd/maps/Kconfig
-@@ -620,5 +620,10 @@ config MTD_PLATRAM
-
- This selection automatically selects the map_ram driver.
-
-+config MTD_ADM5120
-+ tristate "Map driver for ADMtek ADM5120 boards"
-+ depends on MIPS_ADM5120
-+ select MTD_CFI_AMDSTD
-+
- endmenu
-
-Index: linux-2.6.22-rc6/drivers/mtd/maps/Makefile
-===================================================================
---- linux-2.6.22-rc6.orig/drivers/mtd/maps/Makefile
-+++ linux-2.6.22-rc6/drivers/mtd/maps/Makefile
-@@ -47,6 +47,7 @@ obj-$(CONFIG_MTD_OCELOT) += ocelot.o
- obj-$(CONFIG_MTD_SOLUTIONENGINE)+= solutionengine.o
- obj-$(CONFIG_MTD_PCI) += pci.o
- obj-$(CONFIG_MTD_ALCHEMY) += alchemy-flash.o
-+obj-$(CONFIG_MTD_ADM5120) += adm5120_mtd.o
- obj-$(CONFIG_MTD_LASAT) += lasat.o
- obj-$(CONFIG_MTD_AUTCPU12) += autcpu12-nvram.o
- obj-$(CONFIG_MTD_EDB7312) += edb7312.o
+++ /dev/null
-Index: linux-2.6.22-rc6/drivers/net/Kconfig
-===================================================================
---- linux-2.6.22-rc6.orig/drivers/net/Kconfig
-+++ linux-2.6.22-rc6/drivers/net/Kconfig
-@@ -574,6 +574,10 @@ config MIPS_AU1X00_ENET
- If you have an Alchemy Semi AU1X00 based system
- say Y. Otherwise, say N.
-
-+config MIPS_ADM5120_ENET
-+ tristate "MIPS ADM5120 Ethernet switch support"
-+ depends on NET_ETHERNET && MIPS_ADM5120
-+
- config NET_SB1250_MAC
- tristate "SB1250 Ethernet support"
- depends on NET_ETHERNET && SIBYTE_SB1xxx_SOC
-Index: linux-2.6.22-rc6/drivers/net/Makefile
-===================================================================
---- linux-2.6.22-rc6.orig/drivers/net/Makefile
-+++ linux-2.6.22-rc6/drivers/net/Makefile
-@@ -165,6 +165,7 @@ obj-$(CONFIG_SC92031) += sc92031.o
- # This is also a 82596 and should probably be merged
- obj-$(CONFIG_LP486E) += lp486e.o
-
-+obj-$(CONFIG_MIPS_ADM5120_ENET) += adm5120sw.o
- obj-$(CONFIG_ETH16I) += eth16i.o
- obj-$(CONFIG_ZORRO8390) += zorro8390.o
- obj-$(CONFIG_HPLANCE) += hplance.o 7990.o
+++ /dev/null
-Index: linux-2.6.22-rc6/drivers/serial/Makefile
-===================================================================
---- linux-2.6.22-rc6.orig/drivers/serial/Makefile
-+++ linux-2.6.22-rc6/drivers/serial/Makefile
-@@ -21,6 +21,7 @@ obj-$(CONFIG_SERIAL_8250_EXAR_ST16C554)
- obj-$(CONFIG_SERIAL_8250_HUB6) += 8250_hub6.o
- obj-$(CONFIG_SERIAL_8250_MCA) += 8250_mca.o
- obj-$(CONFIG_SERIAL_8250_AU1X00) += 8250_au1x00.o
-+obj-$(CONFIG_SERIAL_ADM5120) += adm5120_uart.o
- obj-$(CONFIG_SERIAL_AMBA_PL010) += amba-pl010.o
- obj-$(CONFIG_SERIAL_AMBA_PL011) += amba-pl011.o
- obj-$(CONFIG_SERIAL_CLPS711X) += clps711x.o
-Index: linux-2.6.22-rc6/include/linux/serial_core.h
-===================================================================
---- linux-2.6.22-rc6.orig/include/linux/serial_core.h
-+++ linux-2.6.22-rc6/include/linux/serial_core.h
-@@ -143,6 +143,9 @@
- #define PORT_KS8695 76
-
-
-+/* ADMtek ADM5120 SoC */
-+#define PORT_ADM5120 77
-+
- #ifdef __KERNEL__
-
- #include <linux/compiler.h>
-Index: linux-2.6.22-rc6/drivers/serial/Kconfig
-===================================================================
---- linux-2.6.22-rc6.orig/drivers/serial/Kconfig
-+++ linux-2.6.22-rc6/drivers/serial/Kconfig
-@@ -270,6 +270,22 @@ config SERIAL_8250_RM9K
-
- comment "Non-8250 serial port support"
-
-+config SERIAL_ADM5120
-+ bool "ADM5120 serial port support"
-+ depends on MIPS_ADM5120
-+ select SERIAL_CORE
-+ select SERIAL_CORE_CONSOLE
-+ help
-+ Driver for the on chip UARTs on the ADM5120 SoC
-+
-+config ADM5120_NR_UARTS
-+ int "Maximum number of ADM5120 serial ports"
-+ depends on SERIAL_ADM5120
-+ default "2"
-+ ---help---
-+ Set this to the number of serial ports you want the driver to
-+ support.
-+
- config SERIAL_AMBA_PL010
- tristate "ARM AMBA PL010 serial port support"
- depends on ARM_AMBA && (BROKEN || !ARCH_VERSATILE)
+++ /dev/null
-Index: linux-2.6.22-rc6/drivers/usb/core/hub.c
-===================================================================
---- linux-2.6.22-rc6.orig/drivers/usb/core/hub.c
-+++ linux-2.6.22-rc6/drivers/usb/core/hub.c
-@@ -464,7 +464,7 @@ void usb_hub_tt_clear_buffer (struct usb
- : (USB_ENDPOINT_XFER_BULK << 11);
- if (usb_pipein (pipe))
- clear->devinfo |= 1 << 15;
--
-+
- /* tell keventd to clear state for this TT */
- spin_lock_irqsave (&tt->lock, flags);
- list_add_tail (&clear->clear_list, &tt->clear_list);
-@@ -540,7 +540,7 @@ static int hub_hub_status(struct usb_hub
- "%s failed (err = %d)\n", __FUNCTION__, ret);
- else {
- *status = le16_to_cpu(hub->status->hub.wHubStatus);
-- *change = le16_to_cpu(hub->status->hub.wHubChange);
-+ *change = le16_to_cpu(hub->status->hub.wHubChange);
- ret = 0;
- }
- mutex_unlock(&hub->status_mutex);
-@@ -1424,7 +1424,7 @@ static int hub_port_status(struct usb_hu
- ret = -EIO;
- } else {
- *status = le16_to_cpu(hub->status->port.wPortStatus);
-- *change = le16_to_cpu(hub->status->port.wPortChange);
-+ *change = le16_to_cpu(hub->status->port.wPortChange);
- ret = 0;
- }
- mutex_unlock(&hub->status_mutex);
-@@ -2007,7 +2007,7 @@ static inline int remote_wakeup(struct u
- * Between connect detection and reset signaling there must be a delay
- * of 100ms at least for debounce and power-settling. The corresponding
- * timer shall restart whenever the downstream port detects a disconnect.
-- *
-+ *
- * Apparently there are some bluetooth and irda-dongles and a number of
- * low-speed devices for which this debounce period may last over a second.
- * Not covered by the spec - but easy to deal with.
-@@ -2142,7 +2142,7 @@ hub_port_init (struct usb_hub *hub, stru
- goto fail;
- }
- oldspeed = udev->speed;
--
-+
- /* USB 2.0 section 5.5.3 talks about ep0 maxpacket ...
- * it's fixed size except for full speed devices.
- * For Wireless USB devices, ep0 max packet is always 512 (tho
-@@ -2168,7 +2168,7 @@ hub_port_init (struct usb_hub *hub, stru
- default:
- goto fail;
- }
--
-+
- type = "";
- switch (udev->speed) {
- case USB_SPEED_LOW: speed = "low"; break;
-@@ -2194,7 +2194,7 @@ hub_port_init (struct usb_hub *hub, stru
- udev->tt = &hub->tt;
- udev->ttport = port1;
- }
--
-+
- /* Why interleave GET_DESCRIPTOR and SET_ADDRESS this way?
- * Because device hardware and firmware is sometimes buggy in
- * this area, and this is how Linux has done it for ages.
-@@ -2230,6 +2230,8 @@ hub_port_init (struct usb_hub *hub, stru
- USB_DT_DEVICE << 8, 0,
- buf, GET_DESCRIPTOR_BUFSIZE,
- USB_CTRL_GET_TIMEOUT);
-+printk(KERN_CRIT "usb_control_msg: %d %d %d (%d)\n", r, buf->bMaxPacketSize0,
-+buf->bDescriptorType, USB_DT_DEVICE);
- switch (buf->bMaxPacketSize0) {
- case 8: case 16: case 32: case 64: case 255:
- if (buf->bDescriptorType ==
-@@ -2281,7 +2283,7 @@ hub_port_init (struct usb_hub *hub, stru
- udev->devnum, retval);
- goto fail;
- }
--
-+
- /* cope with hardware quirkiness:
- * - let SET_ADDRESS settle, some device hardware wants it
- * - read ep0 maxpacket even for high and low speed,
-@@ -2318,7 +2320,7 @@ hub_port_init (struct usb_hub *hub, stru
- udev->ep0.desc.wMaxPacketSize = cpu_to_le16(i);
- ep0_reinit(udev);
- }
--
-+
- retval = usb_get_device_descriptor(udev, USB_DT_DEVICE_SIZE);
- if (retval < (signed)sizeof(udev->descriptor)) {
- dev_err(&udev->dev, "device descriptor read/%s, error %d\n",
-@@ -2416,7 +2418,7 @@ static void hub_port_connect_change(stru
- struct device *hub_dev = hub->intfdev;
- u16 wHubCharacteristics = le16_to_cpu(hub->descriptor->wHubCharacteristics);
- int status, i;
--
-+
- dev_dbg (hub_dev,
- "port %d, status %04x, change %04x, %s\n",
- port1, portstatus, portchange, portspeed (portstatus));
-@@ -2425,7 +2427,7 @@ static void hub_port_connect_change(stru
- set_port_led(hub, port1, HUB_LED_AUTO);
- hub->indicator[port1-1] = INDICATOR_AUTO;
- }
--
-+
- /* Disconnect any existing devices under this port */
- if (hdev->children[port1-1])
- usb_disconnect(&hdev->children[port1-1]);
-@@ -2455,7 +2457,7 @@ static void hub_port_connect_change(stru
- if ((wHubCharacteristics & HUB_CHAR_LPSM) < 2
- && !(portstatus & (1 << USB_PORT_FEAT_POWER)))
- set_port_feature(hdev, port1, USB_PORT_FEAT_POWER);
--
-+
- if (portstatus & USB_PORT_STAT_ENABLE)
- goto done;
- return;
-@@ -2535,7 +2537,7 @@ static void hub_port_connect_change(stru
- goto loop_disable;
- }
- }
--
-+
- /* check for devices running slower than they could */
- if (le16_to_cpu(udev->descriptor.bcdUSB) >= 0x0200
- && udev->speed == USB_SPEED_FULL
-@@ -2587,7 +2589,7 @@ loop:
- if (status == -ENOTCONN)
- break;
- }
--
-+
- done:
- hub_port_disable(hub, port1, 1);
- }
-@@ -2720,7 +2722,7 @@ static void hub_events(void)
- * EM interference sometimes causes badly
- * shielded USB devices to be shutdown by
- * the hub, this hack enables them again.
-- * Works at least with mouse driver.
-+ * Works at least with mouse driver.
- */
- if (!(portstatus & USB_PORT_STAT_ENABLE)
- && !connect_change
-@@ -2750,7 +2752,7 @@ static void hub_events(void)
- "resume on port %d, status %d\n",
- i, ret);
- }
--
-+
- if (portchange & USB_PORT_STAT_C_OVERCURRENT) {
- dev_err (hub_dev,
- "over-current change on port %d\n",
-@@ -2985,7 +2987,7 @@ int usb_reset_device(struct usb_device *
-
- if (ret < 0)
- goto re_enumerate;
--
-+
- /* Device might have changed firmware (DFU or similar) */
- if (memcmp(&udev->descriptor, &descriptor, sizeof descriptor)
- || config_descriptors_changed (udev)) {
-@@ -2993,7 +2995,7 @@ int usb_reset_device(struct usb_device *
- udev->descriptor = descriptor; /* for disconnect() calls */
- goto re_enumerate;
- }
--
-+
- if (!udev->actconfig)
- goto done;
-
-@@ -3031,7 +3033,7 @@ int usb_reset_device(struct usb_device *
-
- done:
- return 0;
--
-+
- re_enumerate:
- hub_port_logical_disconnect(parent_hub, port1);
- return -ENODEV;
-Index: linux-2.6.22-rc6/drivers/usb/host/Kconfig
-===================================================================
---- linux-2.6.22-rc6.orig/drivers/usb/host/Kconfig
-+++ linux-2.6.22-rc6/drivers/usb/host/Kconfig
-@@ -224,3 +224,6 @@ config USB_SL811_CS
- To compile this driver as a module, choose M here: the
- module will be called "sl811_cs".
-
-+config USB_ADM5120_HCD
-+ tristate "ADM5120 HCD support"
-+ depends on USB && MIPS_ADM5120
-Index: linux-2.6.22-rc6/drivers/usb/host/Makefile
-===================================================================
---- linux-2.6.22-rc6.orig/drivers/usb/host/Makefile
-+++ linux-2.6.22-rc6/drivers/usb/host/Makefile
-@@ -8,6 +8,7 @@ endif
-
- obj-$(CONFIG_PCI) += pci-quirks.o
-
-+obj-$(CONFIG_USB_ADM5120_HCD) += adm5120-hcd.o
- obj-$(CONFIG_USB_EHCI_HCD) += ehci-hcd.o
- obj-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o
- obj-$(CONFIG_USB_OHCI_HCD) += ohci-hcd.o
-Index: linux-2.6.22-rc6/drivers/usb/Kconfig
-===================================================================
---- linux-2.6.22-rc6.orig/drivers/usb/Kconfig
-+++ linux-2.6.22-rc6/drivers/usb/Kconfig
-@@ -88,8 +88,6 @@ source "drivers/usb/storage/Kconfig"
-
- source "drivers/usb/image/Kconfig"
-
--source "drivers/usb/mon/Kconfig"
--
- comment "USB port drivers"
- depends on USB
-
-Index: linux-2.6.22-rc6/drivers/usb/Makefile
-===================================================================
---- linux-2.6.22-rc6.orig/drivers/usb/Makefile
-+++ linux-2.6.22-rc6/drivers/usb/Makefile
-@@ -16,6 +16,7 @@ obj-$(CONFIG_USB_UHCI_HCD) += host/
- obj-$(CONFIG_USB_SL811_HCD) += host/
- obj-$(CONFIG_USB_U132_HCD) += host/
- obj-$(CONFIG_USB_OHCI_AT91) += host/
-+obj-$(CONFIG_USB_ADM5120_HCD) += host/
-
- obj-$(CONFIG_USB_ACM) += class/
- obj-$(CONFIG_USB_PRINTER) += class/
+++ /dev/null
-Index: linux-2.6.22-rc6/drivers/leds/Kconfig
-===================================================================
---- linux-2.6.22-rc6.orig/drivers/leds/Kconfig
-+++ linux-2.6.22-rc6/drivers/leds/Kconfig
-@@ -20,6 +20,27 @@ config LEDS_CLASS
-
- comment "LED drivers"
-
-+config LEDS_GPIO
-+ tristate "LED support for LEDS on GPIO lines"
-+ depends on LEDS_CLASS && GENERIC_GPIO
-+ help
-+ This option enables support for LEDs connected to GPIO lines
-+
-+config LEDS_ADM5120
-+ tristate "LED Support for ADM5120 GPIO LEDs"
-+ depends on LEDS_GPIO && MIPS_ADM5120
-+ help
-+ This option enables support for LEDs connected to GPIO lines
-+ on ADM5120 SoC based platforms.
-+
-+config LEDS_ADM5120_EXPERIMENTAL
-+ bool "Enable ADM5120 LEDs experimental code"
-+ depends on LEDS_ADM5120
-+
-+config LEDS_ADM5120_DIAG
-+ bool "Enable ADM5120 LEDs diagnostic mode"
-+ depends on LEDS_ADM5120
-+
- config LEDS_CORGI
- tristate "LED Support for the Sharp SL-C7x0 series"
- depends on LEDS_CLASS && PXA_SHARP_C7xx
-Index: linux-2.6.22-rc6/drivers/leds/Makefile
-===================================================================
---- linux-2.6.22-rc6.orig/drivers/leds/Makefile
-+++ linux-2.6.22-rc6/drivers/leds/Makefile
-@@ -5,6 +5,8 @@ obj-$(CONFIG_LEDS_CLASS) += led-class.o
- obj-$(CONFIG_LEDS_TRIGGERS) += led-triggers.o
-
- # LED Platform Drivers
-+obj-$(CONFIG_LEDS_GPIO) += leds-gpio.o
-+obj-$(CONFIG_LEDS_ADM5120) += leds-adm5120.o
- obj-$(CONFIG_LEDS_CORGI) += leds-corgi.o
- obj-$(CONFIG_LEDS_LOCOMO) += leds-locomo.o
- obj-$(CONFIG_LEDS_SPITZ) += leds-spitz.o
+++ /dev/null
-Index: linux-2.6.22-rc6/arch/mips/pci/Makefile
-===================================================================
---- linux-2.6.22-rc6.orig/arch/mips/pci/Makefile
-+++ linux-2.6.22-rc6/arch/mips/pci/Makefile
-@@ -50,3 +50,4 @@ obj-$(CONFIG_TOSHIBA_RBTX4938) += fixup-
- obj-$(CONFIG_VICTOR_MPC30X) += fixup-mpc30x.o
- obj-$(CONFIG_ZAO_CAPCELLA) += fixup-capcella.o
- obj-$(CONFIG_WR_PPMC) += fixup-wrppmc.o
-+obj-$(CONFIG_PCI_ADM5120) += fixup-adm5120.o ops-adm5120.o pci-adm5120.o
-Index: linux-2.6.22-rc6/include/linux/pci_ids.h
-===================================================================
---- linux-2.6.22-rc6.orig/include/linux/pci_ids.h
-+++ linux-2.6.22-rc6/include/linux/pci_ids.h
-@@ -1712,6 +1712,9 @@
- #define PCI_VENDOR_ID_ESDGMBH 0x12fe
- #define PCI_DEVICE_ID_ESDGMBH_CPCIASIO4 0x0111
-
-+#define PCI_VENDOR_ID_ADMTEK 0x1317
-+#define PCI_DEVICE_ID_ADMTEK_ADM5120 0x5120
-+
- #define PCI_VENDOR_ID_SIIG 0x131f
- #define PCI_SUBVENDOR_ID_SIIG 0x131f
- #define PCI_DEVICE_ID_SIIG_1S_10x_550 0x1000
+++ /dev/null
-Index: linux-2.6.22-rc6/include/asm-mips/byteorder.h
-===================================================================
---- linux-2.6.22-rc6.orig/include/asm-mips/byteorder.h
-+++ linux-2.6.22-rc6/include/asm-mips/byteorder.h
-@@ -58,6 +58,35 @@ static __inline__ __attribute_const__ __
-
- #endif /* CONFIG_CPU_MIPSR2 */
-
-+#ifdef CONFIG_ADM5120_HARDWARE_SWAB
-+
-+static __inline__ __attribute_const__ __u16 ___adm5120__swab16(__u16 x)
-+{
-+ __asm__ (
-+ " sh %2, 0xCA(%1) \n"
-+ " lhu %0, 0xCC(%1) \n"
-+ : "=r" (x)
-+ : "r" (0xB2000000), "r" (x));
-+
-+ return x;
-+}
-+
-+static __inline__ __attribute_const__ __u32 ___adm5120__swab32(__u32 x)
-+{
-+ __asm__ (
-+ " sw %2, 0xC8(%1) \n"
-+ " lw %0, 0xCC(%1) \n"
-+ : "=r" (x)
-+ : "r" (0xB2000000), "r" (x));
-+
-+ return x;
-+}
-+
-+#define __arch__swab16(x) ___adm5120__swab16(x)
-+#define __arch__swab32(x) ___adm5120__swab32(x)
-+
-+#endif /* CONFIG_ADM5120_HARDWARE_SWAB */
-+
- #if !defined(__STRICT_ANSI__) || defined(__KERNEL__)
- # define __BYTEORDER_HAS_U64__
- # define __SWAB_64_THRU_32__
+++ /dev/null
-Index: linux-2.6.22-rc6/drivers/mtd/Kconfig
-===================================================================
---- linux-2.6.22-rc6.orig/drivers/mtd/Kconfig
-+++ linux-2.6.22-rc6/drivers/mtd/Kconfig
-@@ -155,6 +155,22 @@ config MTD_AFS_PARTS
- for your particular device. It won't happen automatically. The
- 'armflash' map driver (CONFIG_MTD_ARMFLASH) does this, for example.
-
-+config MTD_MYLOADER_PARTS
-+ tristate "MyLoader partition parsing"
-+ depends on MIPS_ADM5120 && MTD_PARTITIONS
-+ ---help---
-+ MyLoader is a bootloader which allows the user to define partitions
-+ in flash devices, by putting a table in the second erase block
-+ on the device, similar to a partition table. This table gives the
-+ offsets and lengths of the user defined partitions.
-+
-+ If you need code which can detect and parse these tables, and
-+ register MTD 'partitions' corresponding to each image detected,
-+ enable this option.
-+
-+ You will still need the parsing functions to be called by the driver
-+ for your particular device. It won't happen automatically.
-+
- comment "User Modules And Translation Layers"
-
- config MTD_CHAR
-Index: linux-2.6.22-rc6/drivers/mtd/Makefile
-===================================================================
---- linux-2.6.22-rc6.orig/drivers/mtd/Makefile
-+++ linux-2.6.22-rc6/drivers/mtd/Makefile
-@@ -11,6 +11,7 @@ obj-$(CONFIG_MTD_CONCAT) += mtdconcat.o
- obj-$(CONFIG_MTD_REDBOOT_PARTS) += redboot.o
- obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o
- obj-$(CONFIG_MTD_AFS_PARTS) += afs.o
-+obj-$(CONFIG_MTD_MYLOADER_PARTS) += myloader.o
-
- # 'Users' - code which presents functionality to userspace.
- obj-$(CONFIG_MTD_CHAR) += mtdchar.o
+++ /dev/null
-Index: linux-2.6.22-rc6/drivers/mtd/chips/cfi_cmdset_0002.c
-===================================================================
---- linux-2.6.22-rc6.orig/drivers/mtd/chips/cfi_cmdset_0002.c
-+++ linux-2.6.22-rc6/drivers/mtd/chips/cfi_cmdset_0002.c
-@@ -47,12 +47,17 @@
- #define MANUFACTURER_AMD 0x0001
- #define MANUFACTURER_ATMEL 0x001F
- #define MANUFACTURER_SST 0x00BF
-+#define MANUFACTURER_MACRONIX 0x00C2
- #define SST49LF004B 0x0060
- #define SST49LF040B 0x0050
- #define SST49LF008A 0x005a
- #define AT49BV6416 0x00d6
- #define MANUFACTURER_SAMSUNG 0x00ec
-
-+/* Macronix */
-+#define MX29LV160B 0x2249 /* MX29LV160 Bottom-boot chip */
-+#define MX29LV320B 0x22A8 /* MX29LV320 Bottom-boot chip */
-+
- static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *);
- static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
- static int cfi_amdstd_write_buffers(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
-@@ -217,6 +222,35 @@ static void fixup_use_atmel_lock(struct
- mtd->flags |= MTD_STUPID_LOCK;
- }
-
-+#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
-+/*
-+ * Some Macronix chips has bad bootblock information in the CFI table
-+ */
-+static void fixup_macronix_bootloc(struct mtd_info *mtd, void* param)
-+{
-+ struct map_info *map = mtd->priv;
-+ struct cfi_private *cfi = map->fldrv_priv;
-+ struct cfi_pri_amdstd *extp = cfi->cmdset_priv;
-+ __u8 major = extp->MajorVersion;
-+ __u8 minor = extp->MinorVersion;
-+
-+ switch (cfi->id) {
-+ /* TODO: put affected chip ids here */
-+ case MX29LV160B:
-+ case MX29LV320B:
-+ if (((major << 8) | minor) != 0x3131)
-+ break;
-+
-+ if (extp->TopBottom == 2)
-+ break;
-+
-+ extp->TopBottom = 2; /* Bottom boot */
-+ printk("%s: weird Macronix chip detected, id:0x%04X, boot location "
-+ "forced to bottom\n", map->name, cfi->id);
-+ }
-+}
-+#endif /* CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC */
-+
- static struct cfi_fixup cfi_fixup_table[] = {
- #ifdef AMD_BOOTLOC_BUG
- { CFI_MFR_AMD, CFI_ID_ANY, fixup_amd_bootblock, NULL },
-@@ -231,6 +265,9 @@ static struct cfi_fixup cfi_fixup_table[
- { CFI_MFR_ANY, CFI_ID_ANY, fixup_use_write_buffers, NULL, },
- #endif
- { CFI_MFR_ATMEL, CFI_ID_ANY, fixup_convert_atmel_pri, NULL },
-+#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
-+ { MANUFACTURER_MACRONIX, CFI_ID_ANY, fixup_macronix_bootloc, NULL, },
-+#endif
- { 0, 0, NULL, NULL }
- };
- static struct cfi_fixup jedec_fixup_table[] = {
-Index: linux-2.6.22-rc6/drivers/mtd/chips/Kconfig
-===================================================================
---- linux-2.6.22-rc6.orig/drivers/mtd/chips/Kconfig
-+++ linux-2.6.22-rc6/drivers/mtd/chips/Kconfig
-@@ -196,6 +196,14 @@ config MTD_CFI_AMDSTD
- provides support for one of those command sets, used on chips
- including the AMD Am29LV320.
-
-+config MTD_CFI_FIXUP_MACRONIX_BOOTLOC
-+ bool "Force bottom boot for Macronix flash chips"
-+ depends on MTD_CFI_AMDSTD
-+ help
-+ Some Macronix flash chips have wrong boot-block location in the
-+ CFI table, and the driver may detect the type incorrectly. Select
-+ this if your board has such chip.
-+
- config MTD_CFI_STAA
- tristate "Support for ST (Advanced Architecture) flash chips"
- depends on MTD_GEN_PROBE
+++ /dev/null
-Index: linux-2.6.22-rc6/arch/mips/kernel/head.S
-===================================================================
---- linux-2.6.22-rc6.orig/arch/mips/kernel/head.S
-+++ linux-2.6.22-rc6/arch/mips/kernel/head.S
-@@ -129,14 +129,19 @@
- #endif
- .endm
-
--
- j kernel_entry
- nop
--
-+ nop
-+
- /*
- * Reserved space for exception handlers.
- * Necessary for machines which link their kernels at KSEG0.
-+ * Use as temporary storage for the kernel command line, so that it
-+ * can be updated easily without having to relink the kernel.
- */
-+
-+EXPORT(_image_cmdline)
-+ .ascii "CMDLINE:"
- .align 10
-
- EXPORT(stext) # used for profiling
+++ /dev/null
-Index: linux-2.6.22-rc6/drivers/mtd/nand/Kconfig
-===================================================================
---- linux-2.6.22-rc6.orig/drivers/mtd/nand/Kconfig
-+++ linux-2.6.22-rc6/drivers/mtd/nand/Kconfig
-@@ -81,6 +81,12 @@ config MTD_NAND_TS7250
- help
- Support for NAND flash on Technologic Systems TS-7250 platform.
-
-+config MTD_NAND_RB100
-+ tristate "NAND Flash device on RB100 board"
-+ depends on MTD_NAND
-+ help
-+ Support for NAND flash on RB100 platform.
-+
- config MTD_NAND_IDS
- tristate
-
-Index: linux-2.6.22-rc6/drivers/mtd/nand/Makefile
-===================================================================
---- linux-2.6.22-rc6.orig/drivers/mtd/nand/Makefile
-+++ linux-2.6.22-rc6/drivers/mtd/nand/Makefile
-@@ -10,6 +10,7 @@ obj-$(CONFIG_MTD_NAND_CAFE) += cafe_nan
- obj-$(CONFIG_MTD_NAND_SPIA) += spia.o
- obj-$(CONFIG_MTD_NAND_AMS_DELTA) += ams-delta.o
- obj-$(CONFIG_MTD_NAND_TOTO) += toto.o
-+obj-$(CONFIG_MTD_NAND_RB100) += rbmipsnand.o
- obj-$(CONFIG_MTD_NAND_AUTCPU12) += autcpu12.o
- obj-$(CONFIG_MTD_NAND_EDB7312) += edb7312.o
- obj-$(CONFIG_MTD_NAND_AU1550) += au1550nd.o
--- /dev/null
+../adm5120-2.6/patches-2.6.22
\ No newline at end of file
projects / openwrt.git / commitdiff