--- /dev/null
+From 884d3962ef4787c8cf0b8a7a673531c623d1dff8 Mon Sep 17 00:00:00 2001
+From: Darren Etheridge <detheridge@ti.com>
+Date: Fri, 2 Aug 2013 15:35:36 -0500
+Subject: [PATCH 334/752] video: da8xx-fb: adding dt support
+
+Enhancing driver to enable probe triggered by a corresponding dt entry.
+
+Add da8xx-fb.txt documentation to devicetree section.
+
+Obtain fb_videomode details for the connected lcd panel using the
+display timing details present in DT.
+
+Ensure that platform data is present before checking whether platform
+callback is present (the one used to control backlight). So far this
+was not an issue as driver was purely non-DT triggered, but now DT
+support has been added this check must be performed.
+
+v2: squashing multiple commits from Afzal Mohammed (afzal@ti.com)
+v3: remove superfluous cast
+v4: expose both ti,am3352-lcdc and ti,da830-lcdc for .compatible
+ as driver can use enhanced features of all version of the
+ silicon block.
+v5: addressed review comments from Prabhakar Lad
+v6: Changed the .compatible naming to match the existing drm bindings
+ for am33xx devices
+v7: clarify which compatible to use in the documentation for DA850
+
+Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
+Signed-off-by: Darren Etheridge <detheridge@ti.com>
+---
+ .../devicetree/bindings/video/da8xx-fb.txt | 42 +++++++++++++
+ drivers/video/da8xx-fb.c | 66 +++++++++++++++++++-
+ 2 files changed, 105 insertions(+), 3 deletions(-)
+ create mode 100644 Documentation/devicetree/bindings/video/da8xx-fb.txt
+
+--- /dev/null
++++ b/Documentation/devicetree/bindings/video/da8xx-fb.txt
+@@ -0,0 +1,42 @@
++TI LCD Controller on DA830/DA850/AM335x SoC's
++
++Required properties:
++- compatible:
++ DA830, DA850 - "ti,da8xx-tilcdc"
++ AM335x SoC's - "ti,am33xx-tilcdc"
++- reg: Address range of lcdc register set
++- interrupts: lcdc interrupt
++- display-timings: typical videomode of lcd panel, represented as child.
++ Refer Documentation/devicetree/bindings/video/display-timing.txt for
++ display timing binding details. If multiple videomodes are mentioned
++ in display timings node, typical videomode has to be mentioned as the
++ native mode or it has to be first child (driver cares only for native
++ videomode).
++
++Recommended properties:
++- ti,hwmods: Name of the hwmod associated to the LCDC
++
++Example for am335x SoC's:
++
++lcdc@4830e000 {
++ compatible = "ti,am33xx-tilcdc";
++ reg = <0x4830e000 0x1000>;
++ interrupts = <36>;
++ ti,hwmods = "lcdc";
++ status = "okay";
++ display-timings {
++ 800x480p62 {
++ clock-frequency = <30000000>;
++ hactive = <800>;
++ vactive = <480>;
++ hfront-porch = <39>;
++ hback-porch = <39>;
++ hsync-len = <47>;
++ vback-porch = <29>;
++ vfront-porch = <13>;
++ vsync-len = <2>;
++ hsync-active = <1>;
++ vsync-active = <1>;
++ };
++ };
++};
+--- a/drivers/video/da8xx-fb.c
++++ b/drivers/video/da8xx-fb.c
+@@ -36,6 +36,7 @@
+ #include <linux/slab.h>
+ #include <linux/delay.h>
+ #include <linux/lcm.h>
++#include <video/of_display_timing.h>
+ #include <video/da8xx-fb.h>
+ #include <asm/div64.h>
+
+@@ -1311,12 +1312,54 @@ static struct fb_ops da8xx_fb_ops = {
+ .fb_blank = cfb_blank,
+ };
+
++static struct lcd_ctrl_config *da8xx_fb_create_cfg(struct platform_device *dev)
++{
++ struct lcd_ctrl_config *cfg;
++
++ cfg = devm_kzalloc(&dev->dev, sizeof(struct fb_videomode), GFP_KERNEL);
++ if (!cfg)
++ return NULL;
++
++ /* default values */
++
++ if (lcd_revision == LCD_VERSION_1)
++ cfg->bpp = 16;
++ else
++ cfg->bpp = 32;
++
++ /*
++ * For panels so far used with this LCDC, below statement is sufficient.
++ * For new panels, if required, struct lcd_ctrl_cfg fields to be updated
++ * with additional/modified values. Those values would have to be then
++ * obtained from dt(requiring new dt bindings).
++ */
++
++ cfg->panel_shade = COLOR_ACTIVE;
++
++ return cfg;
++}
++
+ static struct fb_videomode *da8xx_fb_get_videomode(struct platform_device *dev)
+ {
+ struct da8xx_lcdc_platform_data *fb_pdata = dev_get_platdata(&dev->dev);
+ struct fb_videomode *lcdc_info;
++ struct device_node *np = dev->dev.of_node;
+ int i;
+
++ if (np) {
++ lcdc_info = devm_kzalloc(&dev->dev,
++ sizeof(struct fb_videomode),
++ GFP_KERNEL);
++ if (!lcdc_info)
++ return NULL;
++
++ if (of_get_fb_videomode(np, lcdc_info, OF_USE_NATIVE_MODE)) {
++ dev_err(&dev->dev, "timings not available in DT\n");
++ return NULL;
++ }
++ return lcdc_info;
++ }
++
+ for (i = 0, lcdc_info = known_lcd_panels;
+ i < ARRAY_SIZE(known_lcd_panels); i++, lcdc_info++) {
+ if (strcmp(fb_pdata->type, lcdc_info->name) == 0)
+@@ -1345,7 +1388,7 @@ static int fb_probe(struct platform_devi
+ int ret;
+ unsigned long ulcm;
+
+- if (fb_pdata == NULL) {
++ if (fb_pdata == NULL && !device->dev.of_node) {
+ dev_err(&device->dev, "Can not get platform data\n");
+ return -ENOENT;
+ }
+@@ -1385,7 +1428,10 @@ static int fb_probe(struct platform_devi
+ break;
+ }
+
+- lcd_cfg = (struct lcd_ctrl_config *)fb_pdata->controller_data;
++ if (device->dev.of_node)
++ lcd_cfg = da8xx_fb_create_cfg(device);
++ else
++ lcd_cfg = fb_pdata->controller_data;
+
+ if (!lcd_cfg) {
+ ret = -EINVAL;
+@@ -1404,7 +1450,7 @@ static int fb_probe(struct platform_devi
+ par->dev = &device->dev;
+ par->lcdc_clk = tmp_lcdc_clk;
+ par->lcdc_clk_rate = clk_get_rate(par->lcdc_clk);
+- if (fb_pdata->panel_power_ctrl) {
++ if (fb_pdata && fb_pdata->panel_power_ctrl) {
+ par->panel_power_ctrl = fb_pdata->panel_power_ctrl;
+ par->panel_power_ctrl(1);
+ }
+@@ -1652,6 +1698,19 @@ static int fb_resume(struct platform_dev
+ #define fb_resume NULL
+ #endif
+
++#if IS_ENABLED(CONFIG_OF)
++static const struct of_device_id da8xx_fb_of_match[] = {
++ /*
++ * this driver supports version 1 and version 2 of the
++ * Texas Instruments lcd controller (lcdc) hardware block
++ */
++ {.compatible = "ti,da8xx-tilcdc", },
++ {.compatible = "ti,am33xx-tilcdc", },
++ {},
++};
++MODULE_DEVICE_TABLE(of, da8xx_fb_of_match);
++#endif
++
+ static struct platform_driver da8xx_fb_driver = {
+ .probe = fb_probe,
+ .remove = fb_remove,
+@@ -1660,6 +1719,7 @@ static struct platform_driver da8xx_fb_d
+ .driver = {
+ .name = DRIVER_NAME,
+ .owner = THIS_MODULE,
++ .of_match_table = of_match_ptr(da8xx_fb_of_match),
+ },
+ };
+ module_platform_driver(da8xx_fb_driver);
--- /dev/null
+From 9a1a810516ae9cb3259b898b6879901c5b44fa90 Mon Sep 17 00:00:00 2001
+From: Prathap M S <msprathap@ti.com>
+Date: Mon, 2 Sep 2013 12:05:23 +0530
+Subject: [PATCH 343/752] video: da8xx-fb: Add API to register wait for vsync
+ callback
+
+This patch adds APIs to register and unregister wait for vsync callback.
+This is derived from commit id 2d44302545da24fd22912d964102bc31a7489e97
+This commit id was part of 3.2 kernel sources.
+
+Signed-off-by: Prathap M S <msprathap@ti.com>
+---
+ drivers/video/da8xx-fb.c | 33 +++++++++++++++++++++++++++++++++
+ include/video/da8xx-fb.h | 4 ++++
+ 2 files changed, 37 insertions(+)
+
+--- a/drivers/video/da8xx-fb.c
++++ b/drivers/video/da8xx-fb.c
+@@ -197,6 +197,9 @@ static struct fb_fix_screeninfo da8xx_fb
+ .accel = FB_ACCEL_NONE
+ };
+
++static vsync_callback_t vsync_cb_handler;
++static void *vsync_cb_arg;
++
+ static struct fb_videomode known_lcd_panels[] = {
+ /* Sharp LCD035Q3DG01 */
+ [0] = {
+@@ -825,6 +828,32 @@ static int lcd_init(struct da8xx_fb_par
+ return 0;
+ }
+
++int register_vsync_cb(vsync_callback_t handler, void *arg, int idx)
++{
++ if ((vsync_cb_handler == NULL) && (vsync_cb_arg == NULL)) {
++ vsync_cb_arg = arg;
++ vsync_cb_handler = handler;
++ } else {
++ return -EEXIST;
++ }
++
++ return 0;
++}
++EXPORT_SYMBOL(register_vsync_cb);
++
++int unregister_vsync_cb(vsync_callback_t handler, void *arg, int idx)
++{
++ if ((vsync_cb_handler == handler) && (vsync_cb_arg == arg)) {
++ vsync_cb_handler = NULL;
++ vsync_cb_arg = NULL;
++ } else {
++ return -ENXIO;
++ }
++
++ return 0;
++}
++EXPORT_SYMBOL(unregister_vsync_cb);
++
+ /* IRQ handler for version 2 of LCDC */
+ static irqreturn_t lcdc_irq_handler_rev02(int irq, void *arg)
+ {
+@@ -862,6 +891,8 @@ static irqreturn_t lcdc_irq_handler_rev0
+ LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG);
+ par->vsync_flag = 1;
+ wake_up_interruptible(&par->vsync_wait);
++ if (vsync_cb_handler)
++ vsync_cb_handler(vsync_cb_arg);
+ }
+
+ if (stat & LCD_END_OF_FRAME1) {
+@@ -937,6 +968,8 @@ static irqreturn_t lcdc_irq_handler_rev0
+ LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG);
+ par->vsync_flag = 1;
+ wake_up_interruptible(&par->vsync_wait);
++ if (vsync_cb_handler)
++ vsync_cb_handler(vsync_cb_arg);
+ }
+ }
+
+--- a/include/video/da8xx-fb.h
++++ b/include/video/da8xx-fb.h
+@@ -91,5 +91,9 @@ struct lcd_sync_arg {
+ /* Proprietary FB_SYNC_ flags */
+ #define FB_SYNC_CLK_INVERT 0x40000000
+
++typedef void (*vsync_callback_t)(void *arg);
++int register_vsync_cb(vsync_callback_t handler, void *arg, int idx);
++int unregister_vsync_cb(vsync_callback_t handler, void *arg, int idx);
++
+ #endif /* ifndef DA8XX_FB_H */
+
--- /dev/null
+From c99bd415829ef29adf71bb1e1b577650f10e93f5 Mon Sep 17 00:00:00 2001
+From: Darren Etheridge <detheridge@ti.com>
+Date: Mon, 4 Nov 2013 12:27:40 -0600
+Subject: [PATCH 752/752] video/da8xx-fb fix defect with vsync callback
+ invocation
+
+Fix defect where SGX is running at half of the expected framerate.
+The original patch (@ commit ID 9a1a810516ae9cb3259b898b6879901c5b44fa90)
+seems to have a mistake where it only calls the callback
+for the even or the odd frames depending on the revision of the LCD controller
+This patch corrects this and invokes the callback for both odd and even frame
+for just the Rev02 version of the LCDC (won't find an SGX GPU on a Rev01).
+
+Signed-off-by: Darren Etheridge <detheridge@ti.com>
+---
+ drivers/video/da8xx-fb.c | 4 ++--
+ 1 file changed, 2 insertions(+), 2 deletions(-)
+
+--- a/drivers/video/da8xx-fb.c
++++ b/drivers/video/da8xx-fb.c
+@@ -903,6 +903,8 @@ static irqreturn_t lcdc_irq_handler_rev0
+ LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG);
+ par->vsync_flag = 1;
+ wake_up_interruptible(&par->vsync_wait);
++ if (vsync_cb_handler)
++ vsync_cb_handler(vsync_cb_arg);
+ }
+
+ /* Set only when controller is disabled and at the end of
+@@ -968,8 +970,6 @@ static irqreturn_t lcdc_irq_handler_rev0
+ LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG);
+ par->vsync_flag = 1;
+ wake_up_interruptible(&par->vsync_wait);
+- if (vsync_cb_handler)
+- vsync_cb_handler(vsync_cb_arg);
+ }
+ }
+
--- /dev/null
+When running with DT, we no longer have a board file that can set up the
+platform data for wlcore. Allow this data to be passed from DT.
+
+Since some platforms use a gpio-irq, add support for passing either the
+irq number or the gpio number. For the latter case, the driver will
+request the gpio and convert it to the irq number. If an irq is
+specified, it'll be used as is.
+
+[Arik - the pdev_data pointer does not belong to us and is freed when
+the device is released. Dereference to our private data first.]
+
+Signed-off-by: Ido Yariv <ido@wizery.com>
+Signed-off-by: Arik Nemtsov <arik@wizery.com>
+---
+ drivers/net/wireless/ti/wlcore/sdio.c | 71 ++++++++++++++++++++++++++++++++---
+ include/linux/wl12xx.h | 3 +-
+ 2 files changed, 67 insertions(+), 7 deletions(-)
+
+--- a/drivers/net/wireless/ti/wlcore/sdio.c
++++ b/drivers/net/wireless/ti/wlcore/sdio.c
+@@ -34,6 +34,7 @@
+ #include <linux/wl12xx.h>
+ #include <linux/pm_runtime.h>
+ #include <linux/printk.h>
++#include <linux/of.h>
+
+ #include "wlcore.h"
+ #include "wl12xx_80211.h"
+@@ -214,6 +215,61 @@ static struct wl1271_if_operations sdio_
+ .set_block_size = wl1271_sdio_set_block_size,
+ };
+
++static const struct of_device_id wlcore_of_match[] = {
++ {
++ .compatible = "wlcore",
++ },
++ {}
++};
++MODULE_DEVICE_TABLE(of, wlcore_of_match);
++
++static struct wl12xx_platform_data *get_platform_data(struct device *dev)
++{
++ struct wl12xx_platform_data *pdata;
++ struct device_node *np;
++ u32 gpio;
++
++ pdata = wl12xx_get_platform_data();
++ if (!IS_ERR(pdata))
++ return kmemdup(pdata, sizeof(*pdata), GFP_KERNEL);
++
++ np = of_find_matching_node(NULL, wlcore_of_match);
++ if (!np) {
++ dev_err(dev, "No platform data set\n");
++ return NULL;
++ }
++
++ pdata = kzalloc(sizeof(*pdata), GFP_KERNEL);
++ if (!pdata) {
++ dev_err(dev, "Can't allocate platform data\n");
++ return NULL;
++ }
++
++ if (of_property_read_u32(np, "irq", &pdata->irq)) {
++ if (!of_property_read_u32(np, "gpio", &gpio) &&
++ !gpio_request_one(gpio, GPIOF_IN, "wlcore_irq")) {
++ pdata->gpio = gpio;
++ pdata->irq = gpio_to_irq(gpio);
++ }
++ }
++
++ /* Optional fields */
++ pdata->use_eeprom = of_property_read_bool(np, "use-eeprom");
++ of_property_read_u32(np, "board-ref-clock", &pdata->board_ref_clock);
++ of_property_read_u32(np, "board-tcxo-clock", &pdata->board_tcxo_clock);
++ of_property_read_u32(np, "platform-quirks", &pdata->platform_quirks);
++
++ return pdata;
++}
++
++static void del_platform_data(struct wl12xx_platform_data *pdata)
++{
++ if (pdata->gpio)
++ gpio_free(pdata->gpio);
++
++ kfree(pdata);
++}
++
+ static int wl1271_probe(struct sdio_func *func,
+ const struct sdio_device_id *id)
+ {
+@@ -248,12 +304,9 @@ static int wl1271_probe(struct sdio_func
+ /* Use block mode for transferring over one block size of data */
+ func->card->quirks |= MMC_QUIRK_BLKSZ_FOR_BYTE_MODE;
+
+- pdev_data->pdata = wl12xx_get_platform_data();
+- if (IS_ERR(pdev_data->pdata)) {
+- ret = PTR_ERR(pdev_data->pdata);
+- dev_err(glue->dev, "missing wlan platform data: %d\n", ret);
++ pdev_data->pdata = get_platform_data(&func->dev);
++ if (!(pdev_data->pdata))
+ goto out_free_glue;
+- }
+
+ /* if sdio can keep power while host is suspended, enable wow */
+ mmcflags = sdio_get_host_pm_caps(func);
+@@ -282,7 +335,7 @@ static int wl1271_probe(struct sdio_func
+ if (!glue->core) {
+ dev_err(glue->dev, "can't allocate platform_device");
+ ret = -ENOMEM;
+- goto out_free_glue;
++ goto out_free_pdata;
+ }
+
+ glue->core->dev.parent = &func->dev;
+@@ -316,6 +369,9 @@ static int wl1271_probe(struct sdio_func
+ out_dev_put:
+ platform_device_put(glue->core);
+
++out_free_pdata:
++ del_platform_data(pdev_data->pdata);
++
+ out_free_glue:
+ kfree(glue);
+
+@@ -329,11 +385,14 @@ out:
+ static void wl1271_remove(struct sdio_func *func)
+ {
+ struct wl12xx_sdio_glue *glue = sdio_get_drvdata(func);
++ struct wlcore_platdev_data *pdev_data = glue->core->dev.platform_data;
++ struct wl12xx_platform_data *pdata = pdev_data->pdata;
+
+ /* Undo decrement done above in wl1271_probe */
+ pm_runtime_get_noresume(&func->dev);
+
+ platform_device_unregister(glue->core);
++ del_platform_data(pdata);
+ kfree(glue);
+ }
+
+--- a/include/linux/wl12xx.h
++++ b/include/linux/wl12xx.h
+@@ -51,11 +51,12 @@ enum {
+ struct wl12xx_platform_data {
+ void (*set_power)(bool enable);
+ /* SDIO only: IRQ number if WLAN_IRQ line is used, 0 for SDIO IRQs */
++ int gpio;
+ int irq;
+ bool use_eeprom;
+ int board_ref_clock;
+ int board_tcxo_clock;
+- unsigned long platform_quirks;
++ u32 platform_quirks;
+ bool pwr_in_suspend;
+ };
+
--- /dev/null
+--- a/arch/arm/boot/dts/am335x-evmsk.dts
++++ b/arch/arm/boot/dts/am335x-evmsk.dts
+@@ -132,6 +132,39 @@
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys_s0 &clkout2_pin>;
+
++ lcd_pins_s0: lcd_pins_s0 {
++ pinctrl-single,pins = <
++ 0x20 0x01 /* gpmc_ad8.lcd_data16, OUTPUT | MODE1 */
++ 0x24 0x01 /* gpmc_ad9.lcd_data17, OUTPUT | MODE1 */
++ 0x28 0x01 /* gpmc_ad10.lcd_data18, OUTPUT | MODE1 */
++ 0x2c 0x01 /* gpmc_ad11.lcd_data19, OUTPUT | MODE1 */
++ 0x30 0x01 /* gpmc_ad12.lcd_data20, OUTPUT | MODE1 */
++ 0x34 0x01 /* gpmc_ad13.lcd_data21, OUTPUT | MODE1 */
++ 0x38 0x01 /* gpmc_ad14.lcd_data22, OUTPUT | MODE1 */
++ 0x3c 0x01 /* gpmc_ad15.lcd_data23, OUTPUT | MODE1 */
++ 0xa0 0x00 /* lcd_data0.lcd_data0, OUTPUT | MODE0 */
++ 0xa4 0x00 /* lcd_data1.lcd_data1, OUTPUT | MODE0 */
++ 0xa8 0x00 /* lcd_data2.lcd_data2, OUTPUT | MODE0 */
++ 0xac 0x00 /* lcd_data3.lcd_data3, OUTPUT | MODE0 */
++ 0xb0 0x00 /* lcd_data4.lcd_data4, OUTPUT | MODE0 */
++ 0xb4 0x00 /* lcd_data5.lcd_data5, OUTPUT | MODE0 */
++ 0xb8 0x00 /* lcd_data6.lcd_data6, OUTPUT | MODE0 */
++ 0xbc 0x00 /* lcd_data7.lcd_data7, OUTPUT | MODE0 */
++ 0xc0 0x00 /* lcd_data8.lcd_data8, OUTPUT | MODE0 */
++ 0xc4 0x00 /* lcd_data9.lcd_data9, OUTPUT | MODE0 */
++ 0xc8 0x00 /* lcd_data10.lcd_data10, OUTPUT | MODE0 */
++ 0xcc 0x00 /* lcd_data11.lcd_data11, OUTPUT | MODE0 */
++ 0xd0 0x00 /* lcd_data12.lcd_data12, OUTPUT | MODE0 */
++ 0xd4 0x00 /* lcd_data13.lcd_data13, OUTPUT | MODE0 */
++ 0xd8 0x00 /* lcd_data14.lcd_data14, OUTPUT | MODE0 */
++ 0xdc 0x00 /* lcd_data15.lcd_data15, OUTPUT | MODE0 */
++ 0xe0 0x00 /* lcd_vsync.lcd_vsync, OUTPUT | MODE0 */
++ 0xe4 0x00 /* lcd_hsync.lcd_hsync, OUTPUT | MODE0 */
++ 0xe8 0x00 /* lcd_pclk.lcd_pclk, OUTPUT | MODE0 */
++ 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OUTPUT | MODE0 */
++ >;
++ };
++
+ user_leds_s0: user_leds_s0 {
+ pinctrl-single,pins = <
+ 0x10 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad4.gpio1_4 */
+@@ -495,6 +528,27 @@
+ rx-num-evt = <1>;
+ };
+
++&lcdc {
++ pinctrl-names = "default";
++ pinctrl-0 = <&lcd_pins_s0>;
++ status = "okay";
++ display-timings {
++ 480x272 {
++ hactive = <480>;
++ vactive = <272>;
++ hback-porch = <43>;
++ hfront-porch = <8>;
++ hsync-len = <4>;
++ vback-porch = <12>;
++ vfront-porch = <4>;
++ vsync-len = <10>;
++ clock-frequency = <9000000>;
++ hsync-active = <0>;
++ vsync-active = <0>;
++ };
++ };
++};
++
+ &tscadc {
+ status = "okay";
+ tsc {
--- /dev/null
+--- a/arch/arm/boot/dts/am335x-evmsk.dts
++++ b/arch/arm/boot/dts/am335x-evmsk.dts
+@@ -14,6 +14,7 @@
+ /dts-v1/;
+
+ #include "am33xx.dtsi"
++#include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/pwm/pwm.h>
+
+ / {
+@@ -26,6 +27,13 @@
+ };
+ };
+
++ wlan {
++ compatible = "wlcore";
++
++ gpio = <31>;
++ board-ref-clock = <4>;
++ };
++
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+@@ -45,6 +53,16 @@
+ regulator-boot-on;
+ };
+
++ vmmc_wl: fixedregulator@2 {
++ compatible = "regulator-fixed";
++ regulator-name = "vmmc-wl";
++ regulator-min-microvolt = <1800000>;
++ regulator-max-microvolt = <1800000>;
++ gpio = <&gpio1 29 0>;
++ startup-delay-us = <70000>;
++ enable-active-high;
++ };
++
+ leds {
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_leds_s0>;
+@@ -303,6 +321,20 @@
+ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
+ >;
+ };
++
++ wilink_pins: pinmux_wilink_pins {
++ pinctrl-single,pins = <
++ 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_31 */
++ 0x7c (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_csn0.gpio1_29 */
++ 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
++ 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
++ 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
++ 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
++ 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
++ 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
++ >;
++ };
++
+ };
+
+ &uart0 {
+@@ -512,6 +544,16 @@
+ ti,no-reset-on-init;
+ };
+
++&mmc2 {
++ status = "okay";
++ vmmc-supply = <&vmmc_wl>;
++ bus-width = <4>;
++ pinctrl-names = "default";
++ pinctrl-0 = <&wilink_pins>;
++ ti,non-removable;
++ keep-power-in-suspend;
++};
++
+ &mcasp1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcasp1_pins>;
projects / openwrt.git / commitdiff