--- a/arch/mips/ath79/mach-ubnt-xm.c
+++ b/arch/mips/ath79/mach-ubnt-xm.c
-@@ -13,15 +13,17 @@
+@@ -12,16 +12,22 @@
+
#include <linux/init.h>
#include <linux/pci.h>
++#include <linux/platform_device.h>
#include <linux/ath9k_platform.h>
+#include <linux/etherdevice.h>
++#include <linux/ar8216_platform.h>
#include <asm/mach-ath79/irq.h>
++#include <asm/mach-ath79/ar71xx_regs.h>
#include "dev-ap9x-pci.h"
+#include "dev-eth.h"
#include "dev-leds-gpio.h"
#include "dev-m25p80.h"
+#include "dev-usb.h"
++#include "dev-wmac.h"
#include "machtypes.h"
-#include "pci.h"
#define UBNT_XM_GPIO_LED_L1 0
#define UBNT_XM_GPIO_LED_L2 1
-@@ -37,19 +39,19 @@
+@@ -37,19 +43,19 @@
static struct gpio_led ubnt_xm_leds_gpio[] __initdata = {
{
.gpio = UBNT_XM_GPIO_LED_L4,
.active_low = 0,
},
-@@ -66,9 +68,13 @@ static struct gpio_keys_button ubnt_xm_g
+@@ -66,9 +72,13 @@ static struct gpio_keys_button ubnt_xm_g
}
};
ath79_register_leds_gpio(-1, ARRAY_SIZE(ubnt_xm_leds_gpio),
ubnt_xm_leds_gpio);
-@@ -79,9 +85,155 @@ static void __init ubnt_xm_init(void)
+@@ -79,9 +89,242 @@ static void __init ubnt_xm_init(void)
ath79_register_m25p80(NULL);
ap91_pci_init(eeprom, NULL);
+ }
+};
+
-+
+static void __init ubnt_unifi_setup(void)
+{
+ u8 *mac = (u8 *) KSEG1ADDR(0x1fff0000);
+MIPS_MACHINE(ATH79_MACH_UBNT_UNIFI_OUTDOOR, "UBNT-U20",
+ "Ubiquiti UniFiAP Outdoor",
+ ubnt_unifi_outdoor_setup);
++
++static struct gpio_led ubnt_uap_pro_gpio_leds[] __initdata = {
++ {
++ .name = "ubnt:white:dome",
++ .gpio = 12,
++ }, {
++ .name = "ubnt:blue:dome",
++ .gpio = 13,
++ }
++};
++
++static struct gpio_keys_button uap_pro_gpio_keys[] __initdata = {
++ {
++ .desc = "reset",
++ .type = EV_KEY,
++ .code = KEY_RESTART,
++ .debounce_interval = UBNT_XM_KEYS_DEBOUNCE_INTERVAL,
++ .gpio = 17,
++ .active_low = 1,
++ }
++};
++
++static struct ar8327_pad_cfg uap_pro_ar8327_pad0_cfg = {
++ .mode = AR8327_PAD_MAC_RGMII,
++ .txclk_delay_en = true,
++ .rxclk_delay_en = true,
++ .txclk_delay_sel = AR8327_CLK_DELAY_SEL1,
++ .rxclk_delay_sel = AR8327_CLK_DELAY_SEL2,
++};
++
++static struct ar8327_platform_data uap_pro_ar8327_data = {
++ .pad0_cfg = &uap_pro_ar8327_pad0_cfg,
++ .cpuport_cfg = {
++ .force_link = 1,
++ .speed = AR8327_PORT_SPEED_1000,
++ .duplex = 1,
++ .txpause = 1,
++ .rxpause = 1,
++ },
++};
++
++static struct mdio_board_info uap_pro_mdio0_info[] = {
++ {
++ .bus_id = "ag71xx-mdio.0",
++ .phy_addr = 0,
++ .platform_data = &uap_pro_ar8327_data,
++ },
++};
++
++#define UAP_PRO_MAC0_OFFSET 0x0000
++#define UAP_PRO_MAC1_OFFSET 0x0006
++#define UAP_PRO_WMAC_CALDATA_OFFSET 0x1000
++#define UAP_PRO_PCI_CALDATA_OFFSET 0x5000
++
++static void __init ubnt_uap_pro_setup(void)
++{
++ u8 *eeprom = (u8 *) KSEG1ADDR(0x1fff0000);
++
++ ath79_register_m25p80(NULL);
++
++ ath79_register_leds_gpio(-1, ARRAY_SIZE(ubnt_uap_pro_gpio_leds),
++ ubnt_uap_pro_gpio_leds);
++ ath79_register_gpio_keys_polled(-1, UBNT_XM_KEYS_POLL_INTERVAL,
++ ARRAY_SIZE(uap_pro_gpio_keys),
++ uap_pro_gpio_keys);
++
++ ath79_register_wmac(eeprom + UAP_PRO_WMAC_CALDATA_OFFSET, NULL);
++ ap91_pci_init(eeprom + UAP_PRO_PCI_CALDATA_OFFSET, NULL);
++
++ ath79_register_mdio(0, 0x0);
++ mdiobus_register_board_info(uap_pro_mdio0_info,
++ ARRAY_SIZE(uap_pro_mdio0_info));
++
++ ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_RGMII_GMAC0);
++ ath79_init_mac(ath79_eth0_data.mac_addr,
++ eeprom + UAP_PRO_MAC0_OFFSET, 0);
++
++ /* GMAC0 is connected to an AR8327 switch */
++ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
++ ath79_eth0_data.phy_mask = BIT(0);
++ ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
++ ath79_eth0_pll_data.pll_1000 = 0x06000000;
++ ath79_register_eth(0);
++}
++
++MIPS_MACHINE(ATH79_MACH_UBNT_UAP_PRO, "UAP-PRO", "Ubiquiti UniFi AP Pro",
++ ubnt_uap_pro_setup);
++
--- a/arch/mips/ath79/Kconfig
+++ b/arch/mips/ath79/Kconfig
-@@ -71,9 +71,11 @@ config ATH79_MACH_UBNT_XM
- bool "Ubiquiti Networks XM (rev 1.0) board"
+@@ -68,12 +68,16 @@ config ATH79_MACH_PB44
+ Atheros PB44 reference board.
+
+ config ATH79_MACH_UBNT_XM
+- bool "Ubiquiti Networks XM (rev 1.0) board"
++ bool "Ubiquiti Networks XM/UniFi boards"
select SOC_AR724X
++ select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
+ select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
+ select ATH79_DEV_USB
++ select ATH79_DEV_WMAC
help
Say 'Y' here if you want your kernel to support the
Ubiquiti Networks XM (rev 1.0) board.
--- a/arch/mips/ath79/machtypes.h
+++ b/arch/mips/ath79/machtypes.h
-@@ -22,6 +22,12 @@ enum ath79_mach_type {
+@@ -22,6 +22,13 @@ enum ath79_mach_type {
ATH79_MACH_AP81, /* Atheros AP81 reference board */
ATH79_MACH_DB120, /* Atheros DB120 reference board */
ATH79_MACH_PB44, /* Atheros PB44 reference board */
+ ATH79_MACH_UBNT_BULLET_M, /* Ubiquiti Bullet M */
+ ATH79_MACH_UBNT_NANO_M, /* Ubiquiti NanoStation M */
+ ATH79_MACH_UBNT_ROCKET_M, /* Ubiquiti Rocket M */
++ ATH79_MACH_UBNT_UAP_PRO, /* Ubiquiti UniFi AP Pro */
+ ATH79_MACH_UBNT_UNIFI, /* Ubiquiti Unifi */
+ ATH79_MACH_UBNT_UNIFI_OUTDOOR, /* Ubiquiti UnifiAP Outdoor */
ATH79_MACH_UBNT_XM, /* Ubiquiti Networks XM board rev 1.0 */
projects / openwrt.git / blobdiff