target/linux/ramips/dts/WL-351.dts

   1 /dts-v1/;
   2
   3 /include/ "rt3050.dtsi"
   4
   5 / {
   6         compatible = "WL-351", "ralink,rt3052-soc";
   7         model = "Sitecom WL-351 v1 002";
   8
   9         memorydetect {
  10                 ralink,memory = <0x0 0x200000 0x4000000>;
  11         };
  12
  13         palmbus@10000000 {
  14                 sysc@0 {
  15                         ralink,pinmux = "uartlite", "jtag", "sdram", "rgmii";
  16                         ralink,gpiomux = "i2c", "spi", "mdio";
  17                         ralink,uartmux = "gpio";
  18                         ralink,wdtmux = <1>;
  19                 };
  20
  21                 gpio0: gpio@600 {
  22                         status = "okay";
  23                 };
  24
  25         };
  26
  27         cfi@1f000000 {
  28                 compatible = "cfi-flash";
  29                 reg = <0x1f000000 0x800000>;
  30
  31                 bank-width = <2>;
  32                 device-width = <2>;
  33                 #address-cells = <1>;
  34                 #size-cells = <1>;
  35
  36                 partition@0 {
  37                         label = "u-boot";
  38                         reg = <0x0 0x30000>;
  39                         read-only;
  40                 };
  41
  42                 partition@30000 {
  43                         label = "u-boot-env";
  44                         reg = <0x30000 0x10000>;
  45                         read-only;
  46                 };
  47
  48                 factory: partition@40000 {
  49                         label = "factory";
  50                         reg = <0x40000 0x10000>;
  51                         read-only;
  52                 };
  53
  54                 partition@50000 {
  55                         label = "firmware";
  56                         reg = <0x50000 0x3b0000>;
  57                 };
  58         };
  59
  60         ethernet@10100000 {
  61                 status = "okay";
  62         };
  63
  64         esw@10110000 {
  65                 status = "okay";
  66                 ralink,portmap = <0x3f>;
  67                 ralink,fct2 = <0x0002500c>;
  68                 /*
  69                  * ext phy base addr 31, rx/tx clock skew 0,
  70                  * turbo mii off, rgmi 3.3v off, port 5 polling off
  71                  * port5: enabled, gige, full-duplex, rx/tx-flow-control
  72                  * port6: enabled, gige, full-duplex, rx/tx-flow-control
  73                 */
  74                 ralink,fpa2 = <0x1f003fff>;
  75         };
  76
  77         wmac@10180000 {
  78                 status = "okay";
  79         };
  80
  81         otg@101c0000 {
  82                 status = "okay";
  83         };
  84
  85         gpio-leds {
  86                 compatible = "gpio-leds";
  87                 power {
  88                         label = "wl-351:amber:power";
  89                         gpios = <&gpio0 8 1>;
  90                 };
  91                 unpopulated {
  92                         label = "wl-351:amber:unpopulated";
  93                         gpios = <&gpio0 12 1>;
  94                 };
  95                 unpopulated2 {
  96                         label = "wl-351:blue:unpopulated";
  97                         gpios = <&gpio0 13 1>;
  98                 };
  99         };
 100
 101         gpio-keys-polled {
 102                 compatible = "gpio-keys-polled";
 103                 #address-cells = <1>;
 104                 #size-cells = <0>;
 105                 poll-interval = <20>;
 106                 reset {
 107                         label = "reset";
 108                         gpios = <&gpio0 10 1>;
 109                         linux,code = <0x198>;
 110                 };
 111                 wps {
 112                         label = "wps";
 113                         gpios = <&gpio0 0 1>;
 114                         linux,code = <0x211>;
 115                 };
 116         };
 117
 118         rtl8366rb {
 119                 compatible = "rtl8367rb";
 120                 gpio-sda = <&gpio0 1 0>;
 121                 gpio-sck = <&gpio0 2 0>;
 122         };
 123 };