target/linux/kirkwood/patches-3.18/150-pogoplug_e02.patch

   1 --- a/arch/arm/boot/dts/Makefile
   2 +++ b/arch/arm/boot/dts/Makefile
   3 @@ -147,6 +147,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += kirkwood-
   4         kirkwood-openrd-base.dtb \
   5         kirkwood-openrd-client.dtb \
   6         kirkwood-openrd-ultimate.dtb \
   7 +       kirkwood-pogo_e02.dtb \
   8         kirkwood-rd88f6192.dtb \
   9         kirkwood-rd88f6281-z0.dtb \
  10         kirkwood-rd88f6281-a.dtb \
  11 --- /dev/null
  12 +++ b/arch/arm/boot/dts/kirkwood-pogo_e02.dts
  13 @@ -0,0 +1,114 @@
  14 +/dts-v1/;
  15 +
  16 +#include "kirkwood.dtsi"
  17 +#include "kirkwood-6281.dtsi"
  18 +
  19 +/ {
  20 +       model = "Cloud Engines Pogoplug E02";
  21 +       compatible = "cloudengines,pogoe02", "marvell,kirkwood-88f6281", "marvell,kirkwood";
  22 +
  23 +       memory {
  24 +               device_type = "memory";
  25 +               reg = <0x00000000 0x10000000>;
  26 +       };
  27 +
  28 +       chosen {
  29 +               bootargs = "console=ttyS0,115200n8 earlyprintk";
  30 +       };
  31 +
  32 +       ocp@f1000000 {
  33 +               pinctrl: pin-controller@10000 {
  34 +                       pmx_usb_power_enable: pmx-usb-power-enable {
  35 +                               marvell,pins = "mpp29";
  36 +                               marvell,function = "gpio";
  37 +                       };
  38 +                       pmx_led_green: pmx-led_green {
  39 +                               marvell,pins = "mpp48";
  40 +                               marvell,function = "gpio";
  41 +                       };
  42 +                       pmx_led_orange: pmx-led_orange {
  43 +                               marvell,pins = "mpp49";
  44 +                               marvell,function = "gpio";
  45 +                       };
  46 +               };
  47 +               serial@12000 {
  48 +                       status = "ok";
  49 +               };
  50 +       };
  51 +       gpio-leds {
  52 +               compatible = "gpio-leds";
  53 +               pinctrl-0 = < &pmx_usb_power_enable &pmx_led_orange
  54 +                             &pmx_led_green >;
  55 +               pinctrl-names = "default";
  56 +
  57 +               health {
  58 +                       label = "pogo_e02:green:health";
  59 +                       gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
  60 +                       default-state = "keep";
  61 +               };
  62 +               fault {
  63 +                       label = "pogo_e02:orange:fault";
  64 +                       gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
  65 +               };
  66 +       };
  67 +       regulators {
  68 +               compatible = "simple-bus";
  69 +               #address-cells = <1>;
  70 +               #size-cells = <0>;
  71 +               pinctrl-0 = <&pmx_usb_power_enable>;
  72 +               pinctrl-names = "default";
  73 +
  74 +               usb_power: regulator@1 {
  75 +                       compatible = "regulator-fixed";
  76 +                       reg = <1>;
  77 +                       regulator-name = "USB Power";
  78 +                       regulator-min-microvolt = <5000000>;
  79 +                       regulator-max-microvolt = <5000000>;
  80 +                       enable-active-high;
  81 +                       regulator-always-on;
  82 +                       regulator-boot-on;
  83 +                       gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
  84 +               };
  85 +       };
  86 +};
  87 +
  88 +&nand {
  89 +       chip-delay = <40>;
  90 +       status = "okay";
  91 +
  92 +       partition@0 {
  93 +               label = "u-boot";
  94 +               reg = <0x0000000 0x100000>;
  95 +               read-only;
  96 +       };
  97 +
  98 +       partition@100000 {
  99 +               label = "uImage";
 100 +               reg = <0x0100000 0x400000>;
 101 +       };
 102 +
 103 +       partition@500000 {
 104 +               label = "pogoplug";
 105 +               reg = <0x0500000 0x2000000>;
 106 +       };
 107 +
 108 +       partition@2500000 {
 109 +               label = "root";
 110 +               reg = <0x02500000 0x5b00000>;
 111 +       };
 112 +};
 113 +
 114 +&mdio {
 115 +       status = "okay";
 116 +
 117 +       ethphy0: ethernet-phy@0 {
 118 +               reg = <0>;
 119 +       };
 120 +};
 121 +
 122 +&eth0 {
 123 +       status = "okay";
 124 +       ethernet0-port@0 {
 125 +               phy-handle = <&ethphy0>;
 126 +       };
 127 +};